Development of intimate contact during processing of carbon fiber reinforced Polyamide-6 tapes
Source abstract
Abstract
Contact development between the surfaces of two tapes is considered as a critical step in processing carbon fiber reinforced thermoplastic composites. In this study, the development of intimate contact between carbon fiber reinforced Polyamide-6 (PA-6) tapes is investigated experimentally using consolidation experiments and X-ray computed tomography for quantitative contact characterization. The experimental results indicate that the development of intimate contact occurs in the range of seconds even when temperatures are only slightly above the melting temperature and applied pressures is in the range of 1-4 kPa. Experimental data are compared with the results of the two analytical models proposed by Lee and Springer as well as Yang and Pitchumani. Both models overestimate the time needed to reach full contact for the PA-6 tape. In comparison to previously investigated PEEK materials, PA-6 has a relatively low viscosity and the tapes possess a resin-rich layer near the surface, which seems to influence the contact development process. Besides the assumptions made for viscosity, the sensitivity to input parameters describing the surface topology strongly influence the model results and the accuracy of predictions.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Mechanical Behavior of Composites · Fiber-reinforced polymer composites · Polymer crystallization and properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Chair of Carbon Composites, Department of Mechanical Engineering, Technical University of Munich, Garching, Germany
Experimental Physics II, Institute of Physics, University of Augsburg, Augsburg, Germany
References (24)
Show source-provided references
1. Henne F, Ehard S, Kollmannsberger A, et al. Thermoplastic in situ fiber placement for future rocket motor casings manufacturing. In: SAMPE Europe technical conference 14 , Tampere, Finland, 10–11 September 2014, pp. 46–53.
2. 10.1016/j.compositesa.2013.03.00310.1016/j.compositesa.2013.03.003 ↗
3. 10.1016/S1359-835X(01)00017-310.1016/S1359-835X(01)00017-3 ↗
4. 10.1063/1.167578910.1063/1.1675789 ↗
5. 10.1002/pen.76031240610.1002/pen.760312406 ↗
6. 10.1016/S1359-835X(00)00166-410.1016/S1359-835X(00)00166-4 ↗
7. 10.1002/adv.2017710.1002/adv.20177 ↗
8. 10.1007/978-1-4471-0171-0_410.1007/978-1-4471-0171-0_4 ↗
9. 10.1177/002199830606016210.1177/0021998306060162 ↗
10. 10.1177/00219983970310030210.1177/002199839703100302 ↗
11. 10.1016/j.compositesa.2007.05.00310.1016/j.compositesa.2007.05.003 ↗
12. 10.1177/00219983920260160210.1177/002199839202601602 ↗
13. 10.1177/00219983870210110310.1177/002199838702101103 ↗
14. 10.1023/A:101795021594510.1023/A:1017950215945 ↗
15. Dara PH and Loos AC. Thermoplastic matrix composite processing model. Technical Report 24061, Virginia Polytechnic Institute and State University, USA, 1985.
16. 10.1177/002199831347631810.1177/0021998313476318 ↗
17. 10.1364/AO.34.00020110.1364/AO.34.000201 ↗
18. 10.1109/TAU.1967.116190110.1109/TAU.1967.1161901 ↗
19. 10.1002/(SICI)1099-0488(199710)35:14<2219::AID-POLB3>3.0.CO;2-R10.1002/(SICI)1099-0488(199710)35:14<2219::AID-POLB3>3.0.CO;2-R ↗
20. 10.1002/pen.1100310.1002/pen.11003 ↗
21. 10.3139/217.297610.3139/217.2976 ↗
22. 10.1109/TSMC.1979.431007610.1109/TSMC.1979.4310076 ↗
23. Schaefer PM, Staden M, Zaremba S, et al. Material characterization for determining the consolidation properties of carbon fiber tapes with PA-6 matrix. In: International conference on composite materials 20 , Copenhagen, Denmark, 19–24 July 2015, paper no. 5201-1.
24. 10.1016/j.compositesa.2015.12.01910.1016/j.compositesa.2015.12.019 ↗