journal article·2014-04Open access

Modelling thermal effects in machining of carbon fiber reinforced polymer composites

C Santiuste, J Díaz-Álvarez, X Soldani, H. Miguélez

Abstract

Machining-induced damage is commonly observed when manufacturing components based on carbon fiber reinforced polymer (CFRP) composites. Despite the importance of thermal effects in machining CFRPs, this problem has been poorly analyzed in the literature. Predictive tools are not available for thermal phenomena involved during cutting, while only few experimental studies have been found. In this paper, a three-dimensional (3D) finite element model of orthogonal machining of CFRPs including thermal effects is presented. Predicted thermal and mechanical intralaminar damage showed strong influence of fiber orientation. Thermally affected area was larger than mechanically damaged zone. This fact confirms the importance of accounting for thermal effects when modelling CFRP machining.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Advanced machining processes and optimization · Manufacturing Process and Optimization · Advanced Machining and Optimization Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Continuum Media and Structural Analysis, Universidad Carlos III de Madrid, Madrid, Spain

Department of Bioengineering and Aerospace Engineering, Universidad Carlos III de Madrid, Madrid, Spain

Department of Mechanical Engineering, Universidad Carlos III de Madrid, Madrid, Spain

References (30)

Show source-provided references
1. 10.1177/073168441141626610.1177/0731684411416266 ↗
2. 10.1016/j.compositesb.2013.09.05110.1016/j.compositesb.2013.09.051 ↗
3. 10.1177/073168441038503410.1177/0731684410385034 ↗
4. 10.1177/073168441244465310.1177/0731684412444653 ↗
5. 10.1016/j.compstruct.2011.11.02410.1016/j.compstruct.2011.11.024 ↗
6. 10.1016/j.ijmachtools.2013.03.00910.1016/j.ijmachtools.2013.03.009 ↗
7. 10.1016/S0890-6955(96)00095-810.1016/S0890-6955(96)00095-8 ↗
8. 10.1016/j.cirp.2011.03.07710.1016/j.cirp.2011.03.077 ↗
9. Haddad M · Int J Mach Mach Mater · 2013 · 13 · 289
10. 10.1177/073168441246491310.1177/0731684412464913 ↗
11. 10.1016/S0924-0136(01)00675-610.1016/S0924-0136(01)00675-6 ↗
12. 10.1016/j.compscitech.2009.09.00710.1016/j.compscitech.2009.09.007 ↗
13. 10.1016/j.compstruct.2009.09.02110.1016/j.compstruct.2009.09.021 ↗
14. 10.1016/j.compositesa.2011.04.02310.1016/j.compositesa.2011.04.023 ↗
15. 10.1016/j.compscitech.2004.09.02810.1016/j.compscitech.2004.09.028 ↗
16. 10.1016/j.compstruct.2011.05.03410.1016/j.compstruct.2011.05.034 ↗
17. 10.1177/073168441244465410.1177/0731684412444654 ↗
18. 10.1016/j.compositesa.2012.11.02010.1016/j.compositesa.2012.11.020 ↗
19. 10.1016/j.compstruct.2009.10.03510.1016/j.compstruct.2009.10.035 ↗
20. 10.1016/j.compstruct.2013.10.01410.1016/j.compstruct.2013.10.014 ↗
21. 10.1016/j.ijmachtools.2012.01.00610.1016/j.ijmachtools.2012.01.006 ↗
22. Iliescu D. Approache experimentale et numerique de l'usinage a sec des composites CARBONE/EPOXY . PhD Thesis, France, 2008.
23. Hibbit K. ABAQUS user’s manual 6.4-1 . Pawtucket, Rhode Island, USA, Sorensen Inc., 2003.
24. 10.1016/j.triboint.2010.03.01510.1016/j.triboint.2010.03.015 ↗
25. 10.1016/S0266-3538(99)00126-810.1016/S0266-3538(99)00126-8 ↗
26. 10.1016/j.compstruct.2012.01.01610.1016/j.compstruct.2012.01.016 ↗
27. 10.1016/j.compositesa.2012.10.01210.1016/j.compositesa.2012.10.012 ↗
28. 10.1016/S0263-8223(02)00045-410.1016/S0263-8223(02)00045-4 ↗
29. 10.1016/0266-3538(96)00005-X10.1016/0266-3538(96)00005-X ↗
30. 10.1016/j.ijsolstr.2012.08.01310.1016/j.ijsolstr.2012.08.013 ↗