journal article·2016-01

Improving the interlaminar fracture toughness of carbon/epoxy laminates by directly incorporating with porous carbon nanotube buckypaper

Ling Liu, Lulu Shen, Yexin Zhou

Publisher page

Abstract

In this study, thin carbon nanotube (CNT) buckypapers (BPs) with desired porosity were prepared by using of positive pressure filtration method. The obtained porous BP was then directly incorporated into the middle interface of a composite laminate to improve the interlaminar fracture toughness. Double cantilever beam and end-notch flexure tests were conducted to examine the influence of the obtained BP on mode I and mode II interlaminar fracture toughness ( G IC and G IIC ) of the laminates. Results have shown the porous BPs would significantly enhance the G IC and G IIC up to 74% and 82%, respectively. Improved interfacial bonding and increased large fracture surfaces were obtained for the laminate incorporated with thin CNT BPs. Similar enhancement was also detected in acoustic emission energy variation for mode II fracture and auxiliary proved the reinforcing effect of the BP.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Carbon Nanotubes in Composites · Mechanical Behavior of Composites · Smart Materials for Construction

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

School of Aerospace Engineering & Applied Mechanics, Tongji University, Shanghai, PR China

Faculty of Civil Engineering & Mechanics, Jiangsu University, Zhenjiang, PR China

References (25)

Show source-provided references
1. 10.1126/science.265.5176.121210.1126/science.265.5176.1212 ↗
2. 10.1007/s12540-011-1001-710.1007/s12540-011-1001-7 ↗
3. 10.1016/j.carbon.2006.02.03810.1016/j.carbon.2006.02.038 ↗
4. 10.1016/j.mser.2006.06.00110.1016/j.mser.2006.06.001 ↗
5. 10.1021/cr900296210.1021/cr9002962 ↗
6. 10.1016/j.carbon.2013.06.04710.1016/j.carbon.2013.06.047 ↗
7. 10.1016/j.compositesa.2003.09.02910.1016/j.compositesa.2003.09.029 ↗
8. 10.1557/JMR.2008.035610.1557/JMR.2008.0356 ↗
9. 10.1002/adfm.20090066310.1002/adfm.200900663 ↗
10. 10.1002/smll.20090195710.1002/smll.200901957 ↗
11. 10.1016/j.compstruct.2009.08.00910.1016/j.compstruct.2009.08.009 ↗
12. 10.1016/j.compositesa.2011.11.00210.1016/j.compositesa.2011.11.002 ↗
13. 10.1016/j.compstruct.2008.02.01110.1016/j.compstruct.2008.02.011 ↗
14. 10.1016/j.compscitech.2013.08.03410.1016/j.compscitech.2013.08.034 ↗
15. 10.1016/j.compscitech.2008.05.02310.1016/j.compscitech.2008.05.023 ↗
16. 10.1177/073168441037563810.1177/0731684410375638 ↗
17. 10.1016/j.carbon.2012.07.01110.1016/j.carbon.2012.07.011 ↗
18. 10.1016/0010-4361(89)90211-510.1016/0010-4361(89)90211-5 ↗
19. 10.1177/073168441454439110.1177/0731684414544391 ↗
20. 10.1177/073168441558316610.1177/0731684415583166 ↗
21. 10.1177/073168441038306510.1177/0731684410383065 ↗
22. Dzenis YA and Reneker DH. Delamination resistant composites prepared by small diameter fiber reinforcement at ply interfaces. Patent 6265333 B1, USA, 2001.
23. 10.1201/b1367210.1201/b13672 ↗
24. 10.1016/0266-3538(95)00062-310.1016/0266-3538(95)00062-3 ↗
25. 10.1016/j.compstruct.2014.01.02110.1016/j.compstruct.2014.01.021 ↗