Local Buckling of Pultruded FRP Beams-Analysis and Design
Source abstract
Abstract
An investigation of the local compression flange buckling and failure of pultruded fiber-reinforced plastic (FRP) beams is described in this paper. Results of tests on commercially produced pultruded E-glass/polyester and E-glass/vinylester composite material wide-flange I-beams are described. The beams were tested in a four-point bending configuration in a specially designed fixture which was designed to cause local buckling and ultimate failure of the compression flange of the beams and to avoid global lateraltorsional buckling and local web failure. All beams were monitored with strain gages and LVDTs. Buckling loads, failure loads, buckling stresses, deflections and failure modes are reported. Standard and "customized" pultruded beams in the 8 inch (203 mm) series were tested. Based on an analysis of the performance of the standard 8 x 8 x 3/8 in. (203 x 203 x 9.5 mm) beams, two 8 x 8 x 3/8 in. (203 x 203 x 9.5 mm) beams were "customized." In these "customized" beams the fillet region at the flange and web intersection was altered in order to increase its strength and the rotational stiffness. Analysis of the test results of the customized beams indicated that significant increases in load carrying capacity of pultruded beams can be achieved with minor geometry and fiber architecture modifications to the standard beams. A discussion of the differences in buckling and failure characteristics of the beams based on their resins, sizes, and custom modifications is provided.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Structural Behavior of Reinforced Concrete · Structural Analysis of Composite Materials · Mechanical Behavior of Composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Civil Engineering, 7he Catholic University of America, Washington, DC 20064
References (18)
Show source-provided references
1. 10.1520/JTE11531J10.1520/JTE11531J ↗
2. 10.1061/(ASCE)0899-1561(1990)2:2(118)10.1061/(ASCE)0899-1561(1990)2:2(118) ↗
3. Bank, L. C. · Civil Engineering · 1993 · 63 · 64
4. Bank, L. C. · Plastics and Plastic Composites: Material Properties, Part Performance, and Process Simulation · 1991 · 29 · 371
5. Bank, L. C. · 1993
6. Bank, L. C.
7. 10.1061/(ASCE)0899-1561(1991)3:4(292)10.1061/(ASCE)0899-1561(1991)3:4(292) ↗
8. 10.1061/(ASCE)0899-1561(1993)5:3(339)10.1061/(ASCE)0899-1561(1993)5:3(339) ↗
9. Creative Pultrusions · 1988
10. Magnell, C. · CI on Composites · 1993 · 2
11. 10.1061/(ASCE)0733-9445(1992)118:7(1937)10.1061/(ASCE)0733-9445(1992)118:7(1937) ↗
12. Mottram, J. T. · The Structural Engineer · 1991 · 69 · 211
13. 10.1016/0010-4361(92)90108-710.1016/0010-4361(92)90108-7 ↗
14. Scott, D. W. · 1992 · 572
15. 15. Schweitzer, J. 1992. Personal communication.
16. Tarricone, P. · Civil Engineering · 1993 · 62
17. Yoon, S. J. · 1992 · 309
18. 18. Zureick, A. 1993. Personal communication