Experimental analysis of special tool geometries when drilling woven and multidirectional CFRPs
Source abstract
Abstract
Drilling is one of the most frequent machining operations for carbon fiber-reinforced polymer composites, carried out prior to assembly between structural components using mechanical joining. Delamination is the main damage mechanism involved during carbon fiber-reinforced polymer composite drilling causing an elevated percentage of workpiece rejection. Tool geometry strongly influences drilling performance. In this paper, an original work dealing with the comparison between three recently developed configurations (Brad center, Step drill and Reamer drills) in terms of drilling forces and delamination both for woven and tape carbon fiber-reinforced polymers is presented. Reamer drill showed the best results concerning productivity and delamination. Strong differences were found when hole quality obtained in tape and woven composite was compared: multidirectional composite presented poorer hole quality than woven composite under the same cutting conditions. The analysis of variance was developed in order to analyze the influence of each parameter showing the importance of feed rate on surface damage.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced machining processes and optimization · Advanced Machining and Optimization Techniques · Advanced Surface Polishing Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Mechanical Engineering, Universidad Carlos III de Madrid, Madrid, Spain
References (40)
Show source-provided references
1. 10.1016/j.compstruct.2011.11.02410.1016/j.compstruct.2011.11.024 ↗
2. Davim JP · 2010
3. 10.1177/002199830934535410.1177/0021998309345354 ↗
4. 10.3166/rcma.23.357-38510.3166/rcma.23.357-385 ↗
5. 10.1177/073168441038503410.1177/0731684410385034 ↗
6. 10.1177/073168441244465410.1177/0731684412444654 ↗
7. 10.1007/978-3-642-38345-810.1007/978-3-642-38345-8 ↗
8. Davim JP · 2009
9. 10.1016/j.compstruct.2013.10.01410.1016/j.compstruct.2013.10.014 ↗
10. 10.1016/j.matdes.2007.01.01610.1016/j.matdes.2007.01.016 ↗
11. 10.1016/j.jmatprotec.2007.10.05010.1016/j.jmatprotec.2007.10.050 ↗
12. 10.1016/j.ijmachtools.2007.10.01510.1016/j.ijmachtools.2007.10.015 ↗
13. 10.1016/j.compscitech.2006.10.00910.1016/j.compscitech.2006.10.009 ↗
14. 10.1016/j.compstruct.2009.10.03510.1016/j.compstruct.2009.10.035 ↗
15. 10.1016/j.compscitech.2009.01.02510.1016/j.compscitech.2009.01.025 ↗
16. 10.1016/j.ijmachtools.2009.05.00910.1016/j.ijmachtools.2009.05.009 ↗
17. 10.1016/S1359-835X(00)00069-510.1016/S1359-835X(00)00069-5 ↗
18. 10.1016/j.compstruct.2014.06.03410.1016/j.compstruct.2014.06.034 ↗
19. 10.1016/j.cirp.2014.03.07710.1016/j.cirp.2014.03.077 ↗
20. 10.1016/S0261-3069(03)00062-110.1016/S0261-3069(03)00062-1 ↗
21. 10.1016/j.compositesb.2012.07.05710.1016/j.compositesb.2012.07.057 ↗
22. 10.1016/j.ijmachtools.2005.10.00410.1016/j.ijmachtools.2005.10.004 ↗
23. 10.1016/j.matdes.2008.03.02210.1016/j.matdes.2008.03.022 ↗
24. 10.1016/j.ijmachtools.2011.05.00410.1016/j.ijmachtools.2011.05.004 ↗
25. 10.1016/j.ijmachtools.2011.08.00910.1016/j.ijmachtools.2011.08.009 ↗
26. 10.1016/j.jmatprotec.2010.02.01110.1016/j.jmatprotec.2010.02.011 ↗
27. 10.1243/095440502151973510.1243/0954405021519735 ↗
28. Sandvik Coromant. Modern metal cutting: a practical handbook . 1st ed. North American, Sandviken, Sweden: Sandvik Coromant, 1994.
29. Ramirez C, Poulachon G, Rossi F, et al. Tool wear monitoring and hole surface quality during CFRP drilling. In: Procedia CIRP (ed.) 2nd conference on surface integrity (CSI) , Nottingham, UK, 28 May–30 May 2014, pp. 163–168.10.1016/j.procir.2014.04.028 ↗
30. 10.1016/j.triboint.2010.03.01510.1016/j.triboint.2010.03.015 ↗
31. 10.3390/ma706425810.3390/ma7064258 ↗
32. 10.1016/j.ijmachtools.2009.08.00210.1016/j.ijmachtools.2009.08.002 ↗
33. 10.1016/j.jmapro.2012.09.01910.1016/j.jmapro.2012.09.019 ↗
34. 10.3390/ma706444210.3390/ma7064442 ↗
35. 10.1177/073168441351595610.1177/0731684413515956 ↗
36. Guhring Inc. http://www.guhring.com/.
37. http://www.montanabrandtools.com/products/brad-point-drill.
38. http://superiortoolservice.com.nobullsoftware.com/Composite.aspx.
39. Ridgard C. Complex structures for manned/unmanned aerial vehicles. Low temp composite processing mechanical property data. Air Force Research Laboratory. AFRL-RX-WP-TM-2008-4054; 2008.10.21236/ADA477586 ↗
40. Varas D, Artero-Guerrero JA, Pernas-Sánchez J, et al. Analysis of high velocity impacts of steel cylinders on thin carbon/epoxy woven laminates. Compos Struct 2013; 95: 623–629.10.1016/j.compstruct.2012.08.015 ↗