Rotary ultrasonic machining of CFRP using cold air as coolant: feasible regions
Source abstract
Abstract
Carbon fiber reinforced plastic (CFRP) composites are in demand for a variety of applications due to their superior properties. Drilling is involved in many CFRP applications. Experiments have been successfully conducted to use rotary ultrasonic machining (RUM) for CFRP drilling. These experiments were conducted using either cutting fluids or cold air as coolant. RUM of CFRP composites without cutting fluids can eliminate problems caused by cutting fluids, such as high cost of cutting fluids and their disposal, pollution to the environment, and harm to human health. However, dry machining (machining without cutting fluids) also has its limitations, such as burning of machined surface, more friction and adhesion between tool and workpiece, and reduction in tool life. This article presents an experimental study on feasible regions in rotary ultrasonic machining of CFRP using cold air as coolant. Three criteria (burning of machined surface, delamination, and tool blockage) were used to determine feasible regions. Each of four input variables (feedrate, tool rotation speed, ultrasonic power, and cold air pressure) was changed over a wide range so that its feasible region could be found.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced Machining and Optimization Techniques · Advanced machining processes and optimization · Advanced Surface Polishing Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Industrial and Manufacturing Systems Engineering, Kansas State University, Manhattan, USA
Department of Industrial and Manufacturing Systems Engineering, Kansas State University, Manhattan, USA,
Sonic-Mill, Albuquerque, USA
References (34)
Show source-provided references
1. Gay D. · 2003
2. Tong L. · 2002
3. 10.1007/978-1-84882-831-510.1007/978-1-84882-831-5 ↗
4. 10.1016/j.ijmachtools.2005.05.02310.1016/j.ijmachtools.2005.05.023 ↗
5. Sadat AB · Machining of Advanced Materials - Presented at ASME Summer Meeting at University of California · 1995 · 208 · 41
6. 10.1016/S0261-3069(03)00062-110.1016/S0261-3069(03)00062-1 ↗
7. Lambert BK · Carbide Tool J · 1987 · 19 · 31
8. 10.1023/A:101753910083210.1023/A:1017539100832 ↗
9. 10.1201/978148227773910.1201/9781482277739 ↗
10. Schwartz MM · 1992
11. 10.1201/978142002874410.1201/9781420028744 ↗
12. 10.1177/00219983950290150310.1177/002199839502901503 ↗
13. Ruegg CH · Automot Eng-UK · 1981 · 6 · 13
14. Li ZC
15. Cong WL
16. 10.1016/S0007-8506(07)60877-410.1016/S0007-8506(07)60877-4 ↗
17. Byers JP · 2006
18. 10.1016/S0924-0136(00)00445-310.1016/S0924-0136(00)00445-3 ↗
19. Liu CX · Manuf Technol Mach Tool · 1997 · 1 · 30
20. 10.1016/S0924-0136(03)00714-310.1016/S0924-0136(03)00714-3 ↗
21. 10.1088/0022-3727/27/3/00910.1088/0022-3727/27/3/009 ↗
22. Liu J.
23. 10.1016/j.ijmachtools.2006.04.00810.1016/j.ijmachtools.2006.04.008 ↗
24. AiRtx. · 2010
25. 10.1063/1.174089310.1063/1.1740893 ↗
26. Cong WL
27. 10.1016/j.cirp.2009.03.10010.1016/j.cirp.2009.03.100 ↗
28. 10.1016/j.ijmachtools.2007.10.01510.1016/j.ijmachtools.2007.10.015 ↗
29. 10.1177/002199830809220510.1177/0021998308092205 ↗
30. 10.1115/1.290213110.1115/1.2902131 ↗
31. 10.1016/0890-6955(96)00013-210.1016/0890-6955(96)00013-2 ↗
32. 10.1016/j.jmatprotec.2007.10.05010.1016/j.jmatprotec.2007.10.050 ↗
33. 10.1016/j.compscitech.2006.10.00910.1016/j.compscitech.2006.10.009 ↗
34. Cong WL