Mechanical and Physical Properties of Wood-Plastic Composite Panels
Source abstract
Abstract
In this research wood-plastic composite (WPC) panels were produced from high density polyethylene, MDF, and particle-board waste at 60, 70, and 80 wt% fiber loadings using the dry blend/hot press method. Physical and mechanical properties of the panels were studied and compared with conventional MDF and particle-board panels. The results indicated that the studied properties of the composites were strongly affected by the kind and proportion of the wood fiber and polymer. Maximum values of the flexural modulus of the WPC panels were reached at 70% fiber content. The flexural strength and impact strength of the WPC panels declined when fiber content increased from 60 to 80%. The flexural modulus of the WPC panels was lower than that of the virgin MDF panels but the flexural modulus of the composites with 70% fibers was close to that of particle-board panels. Flexural strength of MDF panels was noticeably higher than those of wood-plastic composites whereas the flexural modulus of particle-board panels was comparable to that of the wood-plastic composites at 80% fiber content. Furthermore, water uptake of wood-plastic samples increased with the increase in fiber content; however, it was relatively low compared with virgin MDF and particle-board panels.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Natural Fiber Reinforced Composites · Cellular and Composite Structures · Mechanical Behavior of Composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Wood and Paper Science and Technology College of Natural Resources, University of Tehran, Karaj, Iran
Department of Wood and Paper Science and Technology College of Natural Resources, University of Tehran, Karaj, Iran,
Department of Wood and Paper Science and Technology, College of Natural Resources and Marine Sciences, University of Tarbiat Modares, Noor, Iran
Department of Mechanic Engineering, Isfahan University of Technology, Isfahan, Iran
References (15)
Show source-provided references
1. Rowell, R.M., Sanadi, A.R., Caulfield, D.F. and Jacobson, R.E. ( 1997). Utilization of Natural Fibers in Plastic Composites: Problems and Opportunities. In: Leao, A. L., Carvalho, F. X. and Frollini, E. (eds), Lignocellulosic-Plastics Composites, pp. 23-51, University of Rio de Janeiro.
2. 10.1016/j.compositesa.2004.04.00410.1016/j.compositesa.2004.04.004 ↗
3. Ahmad, I. · Iran. J. Polym. Sci. Technol. · 2007 · 16 · 233
4. 10.1007/s00107-007-0176-610.1007/s00107-007-0176-6 ↗
5. Youngquist, J.A.
6. Wenger, T.H., Youngquist, J.A. and Rowell, R.M. ( 1992). In: Rowell, R. M., Laufenberg, T. L. and Rowell, J. K. (eds), Materials Interactions Relevant to Recycling of Wood-Based Materials, p. 3, Materials Research Society, Pittsburg, PA.
7. Youngquist, J.A. · 1994
8. Chow, P.
9. 10.1016/S0141-3910(03)00025-910.1016/S0141-3910(03)00025-9 ↗
10. 10.1016/j.compositesa.2003.09.01310.1016/j.compositesa.2003.09.013 ↗
11. 10.1002/app.2315910.1002/app.23159 ↗
12. 10.1002/app.2209310.1002/app.22093 ↗
13. Mirbagheri, J. · J. Polym. Sci. Technol. · 2007 · 16 · 271
14. 10.1002/app.2636310.1002/app.26363 ↗
15. Sanadi, A.R.