journal article·1996-02

Effects of Mode Ratio, Ply Orientation and Precracking on the Delamination Toughness of a Laminated Composite

J. J. Polaha, B. D. Davidson, R. C. Hudson, A. Pieracci

Publisher page

Abstract

Results are presented from an investigation of the effects of mode ratio, interfacial ply orientation and precracking on the delamination toughness of a graphite/ epoxy composite. Delamination toughness tests were performed on specimens that exhibited growth at 00/00, 15°/15°, 15°/- 150, 30°/30° and 30°/-30° interfaces. Three mode ratios were considered. The double cantilever beam test was utilized for pure mode I, the end-notched flexure test was used for pure mode II, and the symmetrically delaminated single leg bending test was used for a mixed-mode condition, G,,IG, equal to approximately 0.4. All five interfaces were tested in both precracked and non-precracked conditions at each mode ratio. Also, for the 30°/30° and 30°/- 30° interfaces, two different stacking sequences were used to assess the effect of remote ply orientation on the perceived mode I and mode II toughness. For any mode ratio and interface angle, it was found that precracked toughness values were always lower than the corresponding nonprecracked result. No other consistent trends were observed in all of the data. For the mode I tests, the 30/30 interface exhibited the lowest toughness, for the mixed-mode tests, the 0/0 interface produced a minimum toughness, and for mode II no significant effect of interface angle on toughness was observed. These results are interpreted with the aid of recent three dimensional finite element analyses for energy release rate distributions along the delamination front for the different stacking sequences and test geometries. The accuracy of various data reduction techniques are also evaluated, and suggestions are made for future testing.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Mechanical Behavior of Composites · Fatigue and fracture mechanics · Structural Health Monitoring Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Mechanical, Aerospace and Manufacturing Engineering, Syracuse University, Syracuse, NY 13244

Department of Mechanical, Aerospace and Manufacturing Engineering, Syracuse University, Syracuse, NY 13244;University of Pisa, Department of Aerospace Engineering, 56126 Pisa, Italy.

References (46)

Show source-provided references
1. 10.1520/STP24384S10.1520/STP24384S ↗
2. 10.1016/0010-4361(84)90708-010.1016/0010-4361(84)90708-0 ↗
3. 10.1177/07316844830020010110.1177/073168448300200101 ↗
4. 10.1520/CTR10421J10.1520/CTR10421J ↗
5. 10.1520/STP24373S10.1520/STP24373S ↗
6. Polaha, J. J. · 1707
7. 7. Goetz, D. P. 1988. "Determination of the Mode I Delamination Fracture Toughness of Multi-directional Composite Laminates," Ph.D. Dissertation , Texas A&M University, Department of Mechanical Engineering, December.
8. Hudson, R. C. · 133
9. Russell, A. J. · 1982 · 279
10. Chou, I. · 132
11. 10.1007/BF0003618110.1007/BF00036181 ↗
12. 10.1016/0266-3538(93)90045-I10.1016/0266-3538(93)90045-I ↗
13. Davidson, B. D.
14. 10.2514/3.2520410.2514/3.25204 ↗
15. 10.1520/CTR10078J10.1520/CTR10078J ↗
16. 10.1016/0266-3538(93)90031-B10.1016/0266-3538(93)90031-B ↗
17. 17. Davidson, B. D. and V. Sundararaman. 1994. "A Single Leg Bending Test for Interfacial Fracture Toughness Determination," Syracuse University Department of Mechanical, Aerospace and Manufacturing Engineering Technical Report No. 94-203 (Submitted to International Journal of Fracture).
18. 10.1016/0266-3538(95)00069-010.1016/0266-3538(95)00069-0 ↗
19. 10.1520/STP36314S10.1520/STP36314S ↗
20. Charalambides, M. · International Journal of Fracture · 1992 · 54 · 26910.1007/BF00035361 ↗
21. 10.1007/BF0001812910.1007/BF00018129 ↗
22. Goodelle, J.
23. 10.1080/0021846890803088010.1080/00218468908030880 ↗
24. 10.1177/00219983900240110110.1177/002199839002401101 ↗
25. Crews, J. H. Jr. · 1242
26. 10.1177/00219983950290160210.1177/002199839502901602 ↗
27. 10.1177/00219983880220070410.1177/002199838802200704 ↗
28. Tsai, S. W. · 1980
29. 29. Davidson, B. D., R. Kruger and M. Konig. 1995. "Effect of Stacking Sequence on Energy Release Rate Distributions in Multidirectional DCB and ENF Specimens," Syracuse University Department of Mechanical, Aerospace and Manufacturing Engineering Technical Report Number 95-101 (Submitted to Engineering Fracture Mechanics).
30. 10.1007/978-1-4615-3370-2_9210.1007/978-1-4615-3370-2_92 ↗
31. Krafchak, T. M. · 859
32. 1994
33. 10.1007/978-94-011-9055-810.1007/978-94-011-9055-8 ↗
34. 10.1063/1.172909110.1063/1.1729091 ↗
35. Davidson, B. D. · 155
36. 10.1115/1.289593110.1115/1.2895931 ↗
37. Davidson, B. D. · 1994 · 43
38. 10.1016/0013-7944(87)90115-910.1016/0013-7944(87)90115-9 ↗
39. 10.1177/00219983890230050310.1177/002199838902300503 ↗
40. 10.1016/0013-7944(92)90137-410.1016/0013-7944(92)90137-4 ↗
41. 10.1177/07316844860050030210.1177/073168448600500302 ↗
42. 10.1520/STP10418S10.1520/STP10418S ↗
43. 43. Sundararaman, V. 1996. "Three New Test Methods for Studying the Fracture Mechanics of Bimaterial Interfaces"' Ph.D. Dissertation , Syracuse University, Departnent of Mechanical, Aerospace and Manufacturing Engineering, May.
44. Koudela, K. L. · 1995 · 97
45. 10.1177/00219983860200060610.1177/002199838602000606 ↗
46. Davidson, B. D.