journal article·2026-06Open access

Modeling and half-cell-resolved measurement of the influence of cell degradation on the anode potential of high-energy lithium-ion cells

J. Natterer, F.F. Oehler, S. O’Kane, M. Marinescu, G.J. Offer, A. Jossen

Abstract

Understanding and modeling lithium-ion battery degradation is essential for optimized use but remains a significant challenge, with various aging mechanisms proposed in recent years. Towards a holistic, physics-based model description, the complex interrelationships among aging mechanisms, parameter identification, and experimental validation are highly active research areas. This work presents findings from a one-year, 1000-cycle aging study using multi-reference electrode single-layer pouch cells with NMC-811/graphite. These were utilized to validate a physics-based degradation model based on the Doyle-Fuller-Newman framework, leveraging half-cell-resolved measurement data in a pre-plating regime. The validated model is applied to investigate the influence of different aging mechanisms on the anode’s surface potential, a key parameter for avoiding lithium plating during charging. Additionally, the effects of degradation on anode-potential limited fast charging capability are discussed. Loss of active material is identified as a key mechanism which, if not considered, results in overestimation of the anode potential. Additionally, a significant resistance increase in the cathode material, which alters cell performance during aging, was identified and empirically captured in the model. Without reference electrodes, this resistance increase could not be accurately detected and, as suggested in the literature, would likely have been misattributed to the anode in the aging model. • Single-layer pouch cells with reference electrodes underwent over 1000 cycles. • A physicochemical aging model is validated, revealing critical aging parameters. • The validated aging-sensitive model is then analyzed for the anode potential. • Key degradation mechanisms are identified and discussed for the anode potential.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Advanced Battery Technologies Research · Advancements in Battery Materials · Advanced Battery Materials and Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (96)

Show source-provided references
1. 2025
2. 2025
3. Review and performance comparison of mechanical-chemical degradation models for lithium-ion batteries10.1149/2.0281914jes ↗
4. An overview of degradation phenomena modeling in lithium-ion battery electrodes10.1016/j.coche.2016.08.008 ↗
5. A single particle model for lithium-ion batteries with electrolyte and stress-enhanced diffusion physics10.1149/2.1541704jes ↗
6. Identification of Li ion battery cell aging mechanisms by half-cell and full-cell open-circuit-voltage characteristic analysis10.1016/j.est.2019.100890 ↗
7. Change in the half-cell open-circuit potential curves of silicon–graphite and nickel-rich lithium nickel manganese cobalt oxide during cycle aging10.1016/j.jpowsour.2021.230240 ↗
8. Determination of degradation modes of lithium-ion batteries considering aging-induced changes in the half-cell open-circuit potential curve of silicon–graphite10.1016/j.jpowsour.2022.231296 ↗
9. Investigation of calendar ageing of lithium-ion battery through physical models with ex-situ validation10.1016/j.jpowsour.2024.235076 ↗
10. Critical review of the use of reference electrodes in li-ion batteries: A diagnostic perspective10.3390/batteries5010012 ↗
11. A gold micro-reference electrode for impedance and potential measurements in lithium ion batteries10.1149/2.0581610jes ↗
12. Review—reference electrodes in Li-Ion and next generation batteries: Correct potential assessment, applications and practices10.1149/1945-7111/ac429b ↗
13. Cyclable lithium and capacity loss in Li-ion cells10.1149/1.1870752 ↗
14. Synthesize battery degradation modes via a diagnostic and prognostic model10.1016/j.jpowsour.2012.07.016 ↗
15. Degradation diagnostics for lithium ion cells10.1016/j.jpowsour.2016.12.011 ↗
16. Multimodal physics-based aging model for life prediction of Li-ion batteries10.1149/1.3043429 ↗
17. Simulation and experiment on solid electrolyte interphase (SEI) morphology evolution and lithium-ion diffusion10.1149/2.0521509jes ↗
18. Revealing SEI morphology: in-depth analysis of a modeling approach10.1149/2.0121711jes ↗
19. Electrochemical modeling of linear and nonlinear aging of lithium-ion cells10.1149/1945-7111/aba44f ↗
20. Battery cycle life prediction with coupled chemical degradation and fatigue mechanics10.1149/2.049210jes ↗
21. Modeling mechanical degradation in lithium ion batteries during cycling: Solid electrolyte interphase fracture10.1016/j.jpowsour.2015.09.033 ↗
22. Modeling solid-electrolyte interphase (SEI) fracture: coupled mechanical/Chemical Degradation of the lithium ion battery10.1149/2.0841702jes ↗
23. A SEI modeling approach distinguishing between capacity and power fade10.1149/2.0321712jes ↗
24. Modeling particle versus SEI cracking in lithium-ion battery degradation: Why calendar and cycle aging cannot simply be added10.1149/1945-7111/ad76da ↗
25. Degradation of lithium ion batteries employing graphite negatives and nickel–cobalt–manganese oxide + spinel manganese oxide positives: Part 2, chemical–mechanical degradation model10.1016/j.jpowsour.2014.07.028 ↗
26. Electrochemical thermal-mechanical modelling of stress inhomogeneity in lithium-ion pouch cells10.1149/2.0122001JES ↗
27. Online adaptive anode potential-controlled fast charging of lithium-ion cells using a validated electrochemical model-based virtual reference electrode10.1016/j.jpowsour.2024.234620 ↗
28. Parametric analysis of anodic degradation mechanisms for fast charging lithium batteries with graphite anode10.1016/j.commatsci.2021.110979 ↗
29. Low-temperature charging of lithium-ion cells part I: Electrochemical modeling and experimental investigation of degradation behavior10.1016/j.jpowsour.2013.12.022 ↗
30. Understanding undesirable anode lithium plating issues in lithium-ion batteries10.1039/C6RA19482F ↗
31. Lithium plating mechanism, detection, and mitigation in lithium-ion batteries10.1016/j.pecs.2021.100953 ↗
32. Application of the differential charging voltage analysis to determine the onset of lithium-plating during fast charging of lithium-ion cells10.1016/j.jpowsour.2021.229794 ↗
33. Li plating as unwanted side reaction in commercial Li-ion cells – A review10.1016/j.jpowsour.2018.02.063 ↗
34. Mathematical modeling of the lithium deposition overcharge reaction in lithium-ion batteries using carbon-based negative electrodes10.1149/1.1392512 ↗
35. Multi-reference electrode lithium-ion pouch cell design for spatially resolved half-cell potential and impedance measurements10.1149/1945-7111/ad048d ↗
36. Dynamic cycling enhances battery lifetime10.1038/s41560-024-01675-8 ↗
37. Three-electrode setups for lithium-ion batteries: II. experimental study of different reference electrode designs and their implications for half-cell impedance spectra10.1149/2.0241702jes ↗
38. Development of durable 3-electrode lithium-ion pouch cells with LTO reference mesh: aging and performance studies10.1149/2.0851908jes ↗
39. Overpotential analysis of graphite-based Li-ion batteries seen from a porous electrode modeling perspective10.1016/j.jpowsour.2021.230345 ↗
40. Lithiation and delithiation mechanisms of gold thin film model anodes for lithium ion batteries: Electrochemical characterization10.1016/j.electacta.2015.02.184 ↗
41. Incremental capacity analysis and close-to-equilibrium OCV measurements to quantify capacity fade in commercial rechargeable lithium batteries10.1149/1.2221767 ↗
42. Differential voltage analyses of high-power, lithium-ion cells10.1016/j.jpowsour.2004.07.021 ↗
43. Peak-tracking method to quantify degradation modes in lithium-ion batteries via differential voltage and incremental capacity10.1016/j.est.2021.103669 ↗
44. Calendar aging of NCA lithium-ion batteries investigated by differential voltage analysis and Coulomb tracking10.1149/2.0091701jes ↗
45. Synthesize battery degradation modes via a diagnostic and prognostic model10.1016/j.jpowsour.2012.07.016 ↗
46. User-friendly differential voltage analysis freeware for the analysis of degradation mechanisms in Li-ion batteries10.1149/2.013209jes ↗
47. Charging powers of the electric vehicle fleet: Evolution and implications at commercial charging sites10.1016/j.apenergy.2021.117651 ↗
48. Rate dependency of incremental capacity analysis (dQ/dV) as a diagnostic tool for lithium-ion batteries10.1016/j.est.2020.101329 ↗
49. Electrochemistry of graphite intercalation compounds10.1016/S0378-7753(97)02675-X ↗
50. Surface structural disordering in graphite upon lithium intercalation/deintercalation10.1016/j.jpowsour.2009.12.034 ↗
51. Capacity fade in lithium-ion batteries and cyclic aging over various state-of-charge ranges10.3390/su11236697 ↗
52. Analysis and prediction of the open circuit potential of lithium-ion cells10.1016/j.jpowsour.2012.11.101 ↗
53. DEST: A simplified model and automated tool for loss of lithium inventory and loss of active material estimation in Li-ion batteries10.1002/celc.202300830 ↗
54. Electrode state of health estimation for lithium ion batteries considering half-cell potential change due to aging10.1149/1945-7111/ab8c83 ↗
55. Schmitt · 2023
56. Concealed cathode degradation in lithium-ion cells with a Ni-rich oxide10.1149/1945-7111/ac65b7 ↗
57. Python battery mathematical modelling (PyBaMM)10.5334/jors.309 ↗
58. Modeling of galvanostatic charge and discharge of the lithium/polymer/insertion cell10.1149/1.2221597 ↗
59. Simulation and optimization of the dual lithium ion insertion cell10.1149/1.2054684 ↗
60. Data driven analysis of lithium-ion battery internal resistance towards reliable state of health prediction10.1016/j.jpowsour.2021.230519 ↗
61. Electrochemical characterization and post-mortem analysis of aged LiMn2O4–Li(Ni0.5Mn0.3Co0.2)O2/Graphite lithium ion batteries. Part I: Cycle aging10.1016/j.jpowsour.2013.11.080 ↗
62. The transformation of graphite electrode materials in lithium-ion batteries after cycling10.1016/j.jpowsour.2015.08.055 ↗
63. Identification and quantification of ageing mechanisms in Li-ion batteries by electrochemical impedance spectroscopy10.1016/j.electacta.2022.140801 ↗
64. Electrode side reactions, capacity loss and mechanical degradation in lithium-ion batteries10.1149/2.0291510jes ↗
65. Electrolyte degradation during aging process of lithium-ion batteries: Mechanisms, characterization, and quantitative analysis10.1002/aenm.202304295 ↗
66. Identifying the mechanism of continued growth of the solid–electrolyte interphase10.1002/cssc.201800077 ↗
67. Marquis · 2020
68. Unveiling the interplay of structural and electrochemical degradation of LiNi0.85 Mn0.05 Co0.05 O2 cathode material for Li-ion batteries10.1149/1945-7111/ad6a8f ↗
69. Singlet oxygen evolution from layered transition metal oxide cathode materials and its implications for lithium-ion batteries10.1016/j.mattod.2018.03.037 ↗
70. A shrinking-core model for the degradation of high-nickel cathodes (NMC811) in Li-ion batteries: passivation layer growth and oxygen evolution10.1149/1945-7111/abdc71 ↗
71. Degradation model of high-nickel positive electrodes: Effects of loss of active material and cyclable lithium on capacity fade10.1016/j.jpowsour.2022.232461 ↗
72. Lithium-ion battery degradation: How to model it10.1039/D2CP00417H ↗
73. In situ observation of strains during lithiation of a graphite electrode10.1149/1.3377130 ↗
74. Failure progression in the solid electrolyte interphase (SEI) on silicon electrodes10.1016/j.nanoen.2019.104257 ↗
75. Numerical simulation of intercalation-induced stress in Li-ion battery electrode particles10.1149/1.2759840 ↗
76. Oxygen release and its effect on the cycling stability of LiNix Mny Coz O2 (NMC) cathode materials for Li-ion batteries10.1149/2.0021707jes ↗
77. Role of chemical and structural stabilities on the electrochemical properties of Layered LiNi1/3 Mn1/3 Co1/3 O2 cathodes10.1149/1.1954927 ↗
78. Tin and tin-based intermetallics as new anode materials for lithium-ion cells10.1016/S0378-7753(00)00585-1 ↗
79. Wrinkling and ratcheting of a thin film on cyclically deforming plastic substrate: Mechanical instability of the solid-electrolyte interphase in Li–Ion batteries10.1016/j.jmps.2018.08.006 ↗
80. Understanding Li-ion battery anode degradation and pore morphological changes through nano-resolution X-ray computed tomography10.1149/2.0681613jes ↗
81. Gradient porosity electrodes for fast charging lithium-ion batteries10.1039/D2TA01707E ↗
82. Effect of porosity on the capacity fade of a lithium-ion battery10.1149/1.1759972 ↗
83. Accelerated battery lifetime simulations using adaptive inter-cycle extrapolation algorithm10.1149/1945-7111/ac3e48 ↗
84. Practical identifiability of electrochemical P2D models for lithium-ion batteries10.1007/s10800-021-01579-5 ↗
85. Molecular dynamics simulations of lithium alkyl carbonates10.1021/jp0639142 ↗
86. Improved electrochemical performance and solid electrolyte interphase properties of electrolytes based on lithium bis(fluorosulfonyl)imide for high content silicon anodes10.1039/D2RA01233B ↗
87. Examination of graphite particle cracking as a failure mode in lithium-ion batteries: A model-experimental study10.1149/2.0281504jes ↗
88. A transmission electron microscopy study of crack formation and propagation in electrochemically cycled graphite electrode in lithium-ion cells10.1016/j.jpowsour.2011.05.079 ↗
89. Parametrization of physics-based battery models from input–output data: A review of methodology and current research10.1016/j.jpowsour.2021.230859 ↗
90. How to avoid a perfunctory sensitivity analysis10.1016/j.envsoft.2010.04.012 ↗
91. Time-dependent global sensitivity analysis of the Doyle–Fuller–Newman model10.1016/j.est.2026.121751 ↗
92. The importance of degradation mode analysis in parameterising lifetime prediction models of lithium-ion battery degradation10.1038/s41467-025-57968-3 ↗
93. Non-destructive fast charging algorithm of lithium-ion batteries based on the control-oriented electrochemical model10.1016/j.apenergy.2017.03.111 ↗
94. Modeling and simulation of inhomogeneities in a 18650 nickel-rich, silicon-graphite lithium-ion cell during fast charging10.1016/j.jpowsour.2018.11.043 ↗
95. Investigating anode potential errors of real-time capable dfn type models induced by inhomogeneity for fast charging of cylindrical lithium-ion batteries10.1149/1945-7111/ad5d1d ↗
96. Lithium plating at the cell edge induced by anode overhang during cycling in lithium-ion batteries: Part II. simulation and experimental validation10.1149/1945-7111/ad9a02 ↗