journal article·2026-02Open access

Strain rate sensitivity of NASICON-type Li-ion conductors: Competing mechanism between plastic deformation and crack propagation

Kailin Chen, Lizhong Lang, Tianyi Lyu, Nuo Qu, Gaofeng Li, Yaser Abu-Lebdeh, Yu Zou

Abstract

NASICON-type lithium conductors are promising for their high ionic conductivity and thermal stability. However, their mechanical failure is one of the major challenges that impedes their usage in solid-state lithium-ion batteries. So far, their mechanical behavior under strain rates relevant to battery operation has not been fully understood. This study investigates the strain-rate-dependent mechanical behavior of two NASICON-type Li-ion conductors, Li 1.5 Al 0.5 Ge 1.5 P 3 O 12 (LAGP) and LATGP (the combination of Li 1.3 Al 0.3 Ti 1.7 P 3 O 12 (LATP) and LAGP) using nanoindentation. Averaged from at least 3 tests at a target load of 500 mN and strain rate of 0.12 s −1 , LAGP exhibits a higher Young's modulus (141.2 GPa), nanohardness (10.6 GPa), but lower toughness (0.52 MPa m 1/2 ) compared to LATGP (119.3 GPa, 9.5 GPa and 0.64 MPa m 1/2 , respectively). These differences result from variations in both atomic structures and microstructures. Both materials display decreasing hardness and increasing toughness with increasing strain rate, governed by a competition between plastic deformation and crack propagation. At low strain rates, plasticity enabled by dislocation movement dissipates stress and suppresses crack growth, while high strain rates limit plasticity, concentrating stress and promoting fracture. These findings provide mechanistic insights that guide the mechanical design and operational strategies for durable NASICON-type solid-state batteries.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Advanced Sensor and Energy Harvesting Materials · Advancements in Battery Materials · Dielectric materials and actuators

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (70)

Show source-provided references
1. Promise and reality of post-lithium-ion batteries with high energy densities10.1038/natrevmats.2016.13 ↗
2. Lithium battery chemistries enabled by solid-state electrolytes10.1038/natrevmats.2016.103 ↗
3. A solid future for battery development10.1038/nenergy.2016.141 ↗
4. Filler‐integrated composite polymer electrolyte for solid‐state lithium batteries10.1002/adma.202110423 ↗
5. Prospects of halide-based all-solid-state batteries: from material design to practical application10.1126/sciadv.adc9516 ↗
6. Solid‐state Li–Metal batteries: challenges and Horizons of oxide and sulfide solid electrolytes and their interfaces
7. New lithium-ion conductors based on the NASICON structure10.1039/a807007e ↗
8. Challenges and perspectives of NASICON-type solid electrolytes for all-solid-state lithium batteries10.1088/1361-6528/ab5be7 ↗
9. Superionic conductivity of glass-ceramics in the system Li2O-Al2O3-TiO2-P2O510.1016/S0167-2738(97)00018-0 ↗
10. Fast li+ ion conducting glass-ceramics in the system Li2O-Al2O3-TiO2-P2O510.1016/S0167-2738(97)00434-7 ↗
11. Solid-state batteries: the critical role of mechanics10.1126/science.abg5998 ↗
12. Mechanical instability of electrode-electrolyte interfaces in solid-state batteries
13. Modeling of internal mechanical failure of all-solid-state batteries during electrochemical cycling, and implications for battery design10.1039/C7TA03199H ↗
14. The strength of a constrained lithium layer10.1016/j.actamat.2023.119313 ↗
15. Dendrite initiation and propagation in lithium metal solid-state batteries10.1038/s41586-023-05970-4 ↗
16. Influence of sintering temperature on conductivity and mechanical behavior of the solid electrolyte LATP10.1016/j.ceramint.2019.04.191 ↗
17. Anisotropy of the mechanical properties of Li1.3Al0.3Ti1.7(PO4)3 solid electrolyte material10.1016/j.jpowsour.2019.226940 ↗
18. Mechanical behavior of inorganic lithium-conducting solid electrolytes10.1016/j.jpowsour.2021.230672 ↗
19. An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments10.1557/JMR.1992.1564 ↗
20. Steady-state nanoindentation creep test on β-Sn: a modified constant contact pressure method10.1557/s43578-023-01277-2 ↗
21. A new nanoindentation creep technique using constant contact pressure10.1557/jmr.2019.188 ↗
22. Nanoindentation creep testing: advantages and limitations of the constant contact pressure method10.1557/s43578-021-00445-6 ↗
23. Use of the hardness test to determine other material properties
24. Dependence of elastic stiffness on electronic band structure of nanolaminate M2AlC (M = Ti, V, Nb, and Cr) ceramics10.1103/PhysRevB.69.214111 ↗
25. Elastic modulus versus bond length in lanthanum chromite ceramics10.1016/S0955-2219(97)00143-X ↗
26. The nature of the chemical bond and the structure of molecules and crystals10.1038/148677c0 ↗
27. Recent advances of LATP and their NASICON structure as a solid‐state electrolyte for lithium‐ion batteries10.1002/adem.202300566 ↗
28. Synthesis and properties of NaSICON‐type LATP and LAGP solid electrolytes10.1002/cssc.201900725 ↗
29. Revised effective ionic radii and systematic studies of interatomic distances in halides and chalcogenides
30. Size effects in nanoindentation: an experimental and analytical study10.1007/s00707-009-0222-z ↗
31. Review of nanoindentation size effect: experiments and atomistic simulation10.3390/cryst7100321 ↗
32. Revealing the atomic-scale origin of simultaneously enhanced hardness and crack resistance in a single phase material10.1063/5.0046733 ↗
33. Structural origin of hardness and crack resistance in aluminosilicate glass
34. Structural, thermal, and mechanical characteristics of yttrium lithium borate glasses and glass–ceramics10.1007/s10854-021-07158-w ↗
35. Covalent bonds enhancing and microstructure evolution induced by carbon content in multi-component (TiZrNbMo)Cx ceramics10.1016/j.jmat.2025.101048 ↗
36. Theoretical and experimental investigations of mechanical properties for polymorphous YTaO4 ceramics10.1111/jace.16629 ↗
37. Bond-valence parameters obtained from a systematic analysis of the inorganic crystal structure database
38. Mechanical properties of NaSICON: a brief review10.1007/s11581-022-04820-z ↗
39. Davidge · 1979
40. First-principles investigation of the physical properties of wide band gap hexagonal AlPO4 compound for possible applications
41. Cracking during nanoindentation and its use in the measurement of fracture toughness10.1557/PROC-356-663 ↗
42. Measurement of fracture toughness by nanoindentation methods: recent advances and future challenges10.1016/j.cossms.2015.04.003 ↗
43. Crack deflection processes—I. Theory10.1016/0001-6160(83)90046-9 ↗
44. Porous ceramics: light in weight but heavy in energy and environment technologies10.1016/j.mser.2020.100589 ↗
45. Reinforcement by crack-tip blunting in porous ceramics10.1016/S0955-2219(03)00365-0 ↗
46. The influence of the interphase and associated interfaces on the deflection of matrix cracks in ceramic matrix composites10.1016/S1359-835X(00)00095-6 ↗
47. Toughening materials: enhancing resistance to fracture
48. Toughening of ceramics and ceramic composites through microstructure engineering: a review10.1177/09506608241308337 ↗
49. Evidence for bulk residual stress strengthening in Al2O3/SiC nanocomposites10.1111/j.1151-2916.2002.tb00400.x ↗
50. Tabatabaeian, A.; Ghasemi, A. R.; Shokrieh, M. M.; Marzbanrad, B.; Baraheni, M.; Fotouhi, M. Residual stress in engineering materials: a review. https://doi.org/10.1002/adem.202100786.10.1002/adem.202100786 ↗
51. Diffusion creep in oxide ceramics10.1016/S0955-2219(02)00105-X ↗
52. Frost · 1982
53. Irwin · 1997
54. The activation energy of dislocation movement10.1002/pssb.19650080209 ↗
55. Mechanical behavior of electrochemically lithiated silicon10.1016/j.jpowsour.2014.09.073 ↗
56. Toward all-dislocation-ceramics for high ionic conductivity produced by dry pressing at relatively low temperatures with and without ultrasound10.1063/5.0185747 ↗
57. Characteristics of creep deformation in ceramics10.1179/mst.1991.7.7.577 ↗
58. Mechanism of lithium metal penetration through inorganic solid electrolytes10.1002/aenm.201701003 ↗
59. The impact of elastic deformation on deposition kinetics at lithium/polymer interfaces10.1149/1.1850854 ↗
60. Fracture behavior of solid electrolyte LATP material based on micro-pillar splitting method10.1016/j.jeurceramsoc.2021.04.026 ↗
61. Tradeoff between the ion exchange-induced residual stress and ion transport in solid electrolytes10.1021/acs.chemmater.2c01806 ↗
62. Overcoming the trade-off between ion conduction and stability using thin composite solid electrolyte for high performance all-solid-state lithium battery10.1016/j.electacta.2022.141226 ↗
63. Breaking the trade‐off between ionic conductivity and mechanical strength in solid polymer electrolytes for high‐performance solid lithium batteries10.1002/aenm.202400808 ↗
64. Chemo-mechanical expansion of lithium electrode Materials–on the route to mechanically optimized all-solid-state batteries10.1039/C8EE00907D ↗
65. Electro) chemical expansion during cycling: monitoring the pressure changes in operating solid-state lithium batteries10.1039/C7TA02730C ↗
66. Design principles for zero-strain Li-Ion cathodes10.1016/j.joule.2022.05.018 ↗
67. Approaching practically accessible solid-state batteries: stability issues related to solid electrolytes and interfaces10.1021/acs.chemrev.9b00268 ↗
68. Wang, P.; Tan, J.; Liu, Z.; Wang, C.; Bao, C.; Xia, X.; Li, B.; Liu, Q. Accelerated 3D Percolation Network for Ultra‐High Critical Current Density of Composite Solid‐State Electrolyte. https://doi.org/10.1002/adfm.202512441.10.1002/adfm.202512441 ↗
69. Self-healing Janus interfaces for high-performance LAGP-based lithium metal batteries10.1021/acsenergylett.0c00542 ↗
70. Smart construction of multifunctional Li1.5Al0.5Ge1.5(PO4)3|Li intermediate interfaces for solid-state batteries10.1016/j.ensm.2021.12.043 ↗