journal article·2025-10Open access

Dilatometry study on current rate, temperature, and pressure influence on the expansion behaviour of Si-alloy/graphite - NMC622 pouch cells

Philip Kargl, Bernhard Rasch, Franz Pichler, Christoph Stangl, Mario Marinaro, Margret Wohlfahrt-Mehrens, Alexander Thaler

Abstract

Silicon as anode material gained increased attention over the last years due to its high specific capacity and abundance. The main challenge remains the large volume change upon (de-)lithiation with the consequence of high mechanical stresses and fast degradation. A thorough understanding of the expansion behaviour is crucial for a further improvement silicon-based materials. Therefore, this article provides dilatometry data for stacked pouch cells with a Si-alloy/graphite anode and a NMC622 cathode. The focus is placed on the influence of the applied pressure, the temperature, and the current rate on the cell thickness change. Upon high-rate charging, a significantly increased cell expansion has been observed. The effect is more pronounced at low temperatures and high applied pressures and is assigned to the appearance of lithium plating. The increased cell expansion is accompanied by an excess in measured charging capacity. This effect is further investigated by conducting modified C-rate tests on fresh and aged cells. The presence of plated lithium is confirmed by a post-mortem analysis. A theory based on the appearance of soft short-circuits caused by dendrites is provided as an explanation attempt for the observed effects.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Advanced Battery Technologies Research · Advancements in Battery Materials · Advanced Battery Materials and Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (62)

Show source-provided references
1. Towards high energy density lithium battery anodes: silicon and lithium10.1039/C9SC01201J ↗
2. Lithium-ion batteries – current state of the art and anticipated developments10.1016/j.jpowsour.2020.228708 ↗
3. Diverting exploration of silicon anode into practical way: A review focused on silicon-graphite composite for lithium ion batteries10.1016/j.ensm.2020.11.028 ↗
4. The success story of graphite as a lithium-ion anode material – fundamentals, remaining challenges, and recent developments including silicon (oxide) composites10.1039/D0SE00175A ↗
5. Colossal reversible volume changes in lithium alloys10.1149/1.1388178 ↗
6. Three dimensional studies of particle failure in silicon based composite electrodes for lithium ion batteries10.1016/j.jpowsour.2014.07.001 ↗
7. Lithium ion battery degradation: what you need to know10.1039/D1CP00359C ↗
8. Mechanical damage of surface films and failure of nano-sized silicon electrodes in lithium ion batteries10.1149/2.0141701jes ↗
9. Production of high-energy li-ion batteries comprising silicon-containing anodes and insertion-type cathodes10.1038/s41467-021-25334-8 ↗
10. Recent progress and future perspective on practical silicon anode-based lithium ion batteries10.1016/j.ensm.2022.01.042 ↗
11. Near-zero volume expansion nanoporous silicon as anode for li-ion batteries10.1149/1945-7111/ac8628 ↗
12. Influence of the molecular weight of poly-acrylic acid binder on performance of si-alloy/graphite composite anodes for lithium-ion batteries10.1002/ente.201800302 ↗
13. Towards efficient binders for silicon based lithium-ion battery anodes10.1016/j.cej.2020.126807 ↗
14. Sio x -based graphite composite anode and efficient binders: practical applications in lithium-ion batteries10.1039/D0RA10283K ↗
15. Toward pre-lithiatied high areal capacity silicon anodes for lithium-ion batteries10.1016/j.electacta.2016.03.139 ↗
16. A new approach for compensating the irreversible capacity loss of high-energy si/c—lini0.5mn1.5o4 lithium-ion batteries10.1016/j.jpowsour.2017.03.051 ↗
17. Design and testing of prelithiated full cells with high silicon content10.1149/2.1161805jes ↗
18. Pre-lithiation strategies for next-generation practical lithium-ion batteries10.1002/advs.202005031 ↗
19. Mechanical methods for state determination of lithium-ion secondary batteries: A review10.1016/j.est.2020.101859 ↗
20. Developments in dilatometry for characterisation of electrochemical devices10.1002/batt.202100027 ↗
21. In situ (operando) electrochemical dilatometry as a method to distinguish charge storage mechanisms and metal plating processes for sodium and lithium ions in hard carbon battery electrodes
22. Methods for quantifying expansion in lithium-ion battery cells resulting from cycling: A review10.3390/en17071566 ↗
23. Investigating the effects of silicon and carbon components on the thickness evolution and performance degradation of silicon–carbon electrodes through electrochemical dilatometry10.1016/j.jpowsour.2024.234626 ↗
24. Damage of prismatic lithium–ion cells subject to bending: Test
25. Electrochemical dilatometry of si-bearing electrodes: Dimensional changes and experiment design10.1149/1945-7111/abd465 ↗
26. Electrochemically stable in situ dilatometry of nmc, nca and graphite electrodes for lithium-ion cells compared to xrd measurements10.1149/1945-7111/abf262 ↗
27. Correlation between voltage, strain, and impedance as a function of pressure of a nickel–rich nmc lithium–ion pouch cell10.1002/admt.202301965 ↗
28. Effects of mechanical compression on the aging and the expansion behavior of si/c-composite—nmc811 in different lithium-ion battery cell formats10.1149/2.1121915jes ↗
29. Analysis of the effect of applying external mechanical pressure on next generation silicon alloy lithium-ion cells10.1016/j.electacta.2019.03.138 ↗
30. Stress evolution and capacity fade in constrained lithium-ion pouch cells10.1016/j.jpowsour.2013.06.165 ↗
31. Study of the influence of mechanical pressure on the performance and aging of lithium-ion battery cells10.1016/j.jpowsour.2019.227148 ↗
32. Optimizing mechanical compression for cycle life and irreversible swelling of high energy and high power lithium-ion pouch cells10.1016/j.est.2023.109883 ↗
33. Temperature effect and thermal impact in lithium-ion batteries: A review10.1016/j.pnsc.2018.11.002 ↗
34. A review on temperature-dependent electrochemical properties, aging, and performance of lithium-ion cells10.3390/batteries6030035 ↗
35. Rate dependence of swelling in lithium-ion cells10.1016/j.jpowsour.2014.05.039 ↗
36. Review—lithium plating detection methods in li-ion batteries10.1149/1945-7111/abd3b8 ↗
37. Lithium plating mechanism, detection, and mitigation in lithium-ion batteries10.1016/j.pecs.2021.100953 ↗
38. Dendrite-free lithium deposition via self-healing electrostatic shield mechanism10.1021/ja312241y ↗
39. Mechanisms of dendritic growth investigated by in situ light microscopy during electrodeposition and dissolution of lithium10.1016/j.jpowsour.2014.03.029 ↗
40. Microscopic observations of the formation
41. Mechanistic understanding of li dendrites growth by in- situ/operando imaging techniques10.1016/j.jpowsour.2020.228135 ↗
42. Impact of electrochemical and mechanical interactions on lithium-ion battery performance investigated by operando dilatometry10.1016/j.jpowsour.2021.229457 ↗
43. A review of existing and emerging methods for lithium detection and characterization in li–ion and li–metal batteries10.1002/aenm.202100372 ↗
44. Understanding undesirable anode lithium plating issues in lithium-ion batteries10.1039/C6RA19482F ↗
45. Li plating as unwanted side reaction in commercial li-ion cells – a review10.1016/j.jpowsour.2018.02.063 ↗
46. Temperature dependent ageing mechanisms in lithium-ion batteries – a post-mortem study10.1016/j.jpowsour.2014.03.112 ↗
47. A new method for detecting lithium plating by measuring the cell thickness10.1016/j.jpowsour.2014.03.142 ↗
48. Lithium plating on graphite negative electrodes: Innovative qualitative and quantitative investigation methods10.1149/2.0451514jes ↗
49. Multi-directional laser scanning as innovative method to detect local cell damage during fast charging of lithium-ion cells10.1016/j.est.2016.09.002 ↗
50. Fast-charging of automotive lithium-ion cells: In-situ lithium-plating detection and comparison of different cell designs10.1149/1945-7111/abb564 ↗
51. Internal short circuit mechanisms, experimental approaches and detection methods of lithium-ion batteries for electric vehicles: A review10.1016/j.rser.2021.110790 ↗
52. Analysis of internal short-circuit in a lithium ion cell10.1016/j.jpowsour.2009.05.002 ↗
53. Mechanism
54. Direct observation of internal short circuits by lithium dendrites in cross-sectional lithium-ion in situ full cells10.1016/j.jpowsour.2022.232391 ↗
55. Exploiting self-heat in a lithium metal battery for dendrite healing10.1016/j.ensm.2019.04.013 ↗
56. Dendrite short-circuit and fuse effect on li/polymer/li cells10.1016/j.electacta.2006.02.004 ↗
57. Fusing phenomenon of lithium-ion battery internal short circuit10.1149/2.1721712jes ↗
58. The effects of defects on localized plating in lithium-ion batteries10.1149/2.1051507jes ↗
59. Elimination of voltage noise of poly (ethylene oxide)-based solid electrolytes in high-voltage lithium batteries: Linear versus network polymers10.1016/j.isci.2020.101225 ↗
60. Poly(ethylene oxide)-based electrolyte for solid-state-lithium-batteries with high voltage positive electrodes: Evaluating the role of electrolyte oxidation in rapid cell failure10.1038/s41598-020-61373-9 ↗
61. Investigation of voltage and expansion hysteresis of si-alloy-c/nmc622 pouch cells using dilatometry10.1016/j.jpowsour.2022.232042 ↗
62. Steiger · 2015