The addition of red lead to flat plate and tubular valve regulated miners cap lamp lead–acid batteries
Source abstract
Abstract
The study looked at the use of red lead in the manufacturing of valve regulated lead acid (VRLA) miners cap lamp (MCL) batteries that were made with either flat plate or tubular positive electrodes. A problem with using only grey oxide in the manufacture of thick flat plate or tubular electrodes is the poor conversion of the active material to the desired lead dioxide. The addition of red lead to the initial starting material improves the formation efficiency but is considerably more expensive thereby increasing the cost of manufacturing. The study showed that by carefully controlling the formation conditions in terms of the voltage and temperature of a battery, good capacity performance can be achieved for cells made with flat plate electrodes that contain up to 25% red lead. The small amount of red lead in the active cured material reduces the effect of electrode surface sulphate formation and allows the battery to achieve its rated capacity within the first few cycles. Batteries made with flat plate positive electrodes that contained more that 50% red lead showed good initial capacity but had poor structural active material bonding. The study showed that MCL batteries made with tubular positive electrodes that contained less than 75% red lead resulted in a poorly formed electrode with limited capacity utilization. Pickling and soaking times of the tubular electrodes should be kept at a minimum thereby allowing higher active material utilization during subsequent capacity cycling. The study further showed that it is beneficial to use higher formation rates in order to reduce manufacturing time and to improve the active material characteristics.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Battery Technologies Research · Advanced battery technologies research · Advancements in Battery Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (17)
Show source-provided references
1. Vinal · 1955
2. Berndt · 1993
3. Sealed maintenance-free lead/acid batteries: properties and application of a new battery generation10.1016/0378-7753(88)80060-0 ↗
4. Advantages and disadvantages of valve-regulated, lead/acid batteries10.1016/0378-7753(94)01940-1 ↗
5. W.B. Brecht, The VRLA Debate Rages On, The Battery Man Jan (1995) 12.
6. Sealed lead/acid batteries for portable underground lighting10.1016/0378-7753(89)80095-3 ↗
7. Lead–acid battery pastes containing 4PbO·PbSO4 and Pb3O410.1149/1.2086354 ↗
8. A study of the preparation variable of tubular positive electrodes for lead/acid batteries10.1016/0378-7753(85)80059-8 ↗
9. Determination of optimal formation conditions for tubular positive electrodes of lead/acid batteries10.1016/0013-4686(86)85034-4 ↗
10. The influence of the pickling and curing process in the manufacturing of positive tubular electrodes on the performance of lead–acid batteries10.1016/S0378-7753(02)00693-6 ↗
11. Factors affecting the formation of lead/acid tubular positives. II. Resting and extreme conditions10.1016/0378-7753(83)80019-6 ↗
12. Investigation on soaking and formation of lead/acid battery plates with different mass structure10.1016/S0378-7753(99)00390-0 ↗
13. Calculated x-ray powder diffraction data for phases encountered in lead–acid battery plates10.1016/0378-7753(83)87015-3 ↗
14. Hehner · 1986
15. Aspects of lead/acid battery technology. 3. Plate Curing10.1016/0378-7753(93)85011-C ↗
16. Some structural and textural aspects of tribasic lead sulfate precipitation during the mixing of lead–acid battery positive paste10.1149/1.2050079 ↗
17. Influence of grid alloy and fast charge on battery cycle life and structure of the positive active mass of lead acid batteries10.1016/S0378-7753(00)00598-X ↗