journal article·2023-12

Dynamic bolt forces during cold starts and drying processes of a PEM fuel cell

Maximilian Schmitz, Stefan Pischinger

Publisher page

Abstract

When assembling a fuel cell stack , the individual cells are attached to each other via a clamping system. The clamping system must provide high contact pressures so that the cells are sealed gas-tight and the electrical contact resistance between the cell layers and the bipolar plates is kept low. Due to swelling of the membranes and temperature expansion, the cells expand or contract during operation. For optimum functionality, the clamping system must be designed in such a way that sufficient contact pressure is always present, even at various operating points. In this study, the forces in the tie rods of the clamping system and the expansion of a stack during a cold start and during a drying process after shutdown are analyzed. It is found that the contact forces increase significantly during a cold start and the stack expands. During drying after a shutdown, it is observed that the forces decrease and the stack contracts. It is finally found that residual water content in the membranes can be qualitatively derived from the forces in the tie rods. From this, criteria are formulated when a drying process should be optimally terminated to avoid a complete dry-out of the membranes.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Fuel Cells and Related Materials · Advanced Battery Technologies Research · Electrocatalysts for Energy Conversion

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (24)

Show source-provided references
1. Töpler · 2017
2. 2015
3. Realistic accelerated stress tests for PEM fuel cells: Test procedure development based on standardized automotive driving cycles
4. Kuhlmann · 2017
5. Scholz · 2015
6. Comprehensive investigation of membrane sorption and CFD modeling of a tube membrane humidifier with experimental validation
7. A progress review on gas purge for enhancing cold start performance in PEM fuel cell10.4271/2018-01-1312 ↗
8. Numerical study of gas purge in polymer electrolyte membrane fuel cell10.1016/j.ijheatmasstransfer.2016.07.051 ↗
9. PEMFC operational and design strategies for Sub zero environments
10. 2012
11. Fundamental characterization of evaporative water removal from fuel cell diffusion media10.1016/j.jpowsour.2009.12.084 ↗
12. Study on a purge method using pressure reduction for effective water removal in polymer electrolyte membrane fuel cells10.1016/j.ijhydene.2015.05.136 ↗
13. An intelligent approach for contact pressure optimization of PEM fuel cell gas diffusion layers10.3390/app10124194 ↗
14. A study of contact pressure with thermo-mechanical coupled action for a full-dimensional PEMFC stack10.3390/su14148593 ↗
15. Investigation of the assembly for high-power proton exchange membrane fuel cell stacks through an efficient equivalent model10.1016/j.apenergy.2020.115532 ↗
16. Investigation of contact pressure distribution on gas diffusion layer of fuel cell with pneumatic endplate10.1016/j.apenergy.2020.114663 ↗
17. Experimental study of clamping effects on the performances of a single proton exchange membrane fuel cell and a 10-cell stack10.1016/j.jpowsour.2009.03.058 ↗
18. Composite endplates with pre-curvature for PEMFC (polymer electrolyte membrane fuel cell)10.1016/j.compstruct.2009.10.023 ↗
19. Composite sandwich endplates with a compliant pressure distributor for a PEM fuel cell10.1016/j.compstruct.2014.09.030 ↗
20. Simulation and experimental analysis of the clamping pressure distribution in a PEM fuel cell stack10.1016/j.ijhydene.2013.03.049 ↗
21. Investigation of contact pressure distribution over the active area of PEM fuel cell stack10.1016/j.ijhydene.2015.12.057 ↗
22. Experimental study on clamping pressure distribution in PEM fuel cells10.1016/j.jpowsour.2007.12.055 ↗
23. Simulation and in situ measurement of stress distribution in a polymer electrolyte membrane fuel cell stack10.1016/j.jpowsour.2016.08.073 ↗
24. Firat · 2016