Deconstructing three-dimensional (3D) structure of absorptive glass mat (AGM) separator to tailor pore dimensions and amplify electrolyte uptake
Source abstract
Abstract
Abstract Absorptive glass mat (AGM) separator is a vital technical component in valve regulated lead acid (VRLA) batteries that can be tailored for a desired application. To selectively design and tailor the AGM separator, the intricate three-dimensional (3D) structure needs to be unraveled. Herein, a toolkit of 3D analytical models of pore size distribution and electrolyte uptake expressed via wicking characteristics of AGM separators under unconfined and confined states is presented. 3D data of fiber orientation distributions obtained previously through X-ray micro-computed tomography (microCT) analysis are used as key set of input parameters. The predictive ability of pore size distribution model is assessed through the commonly used experimental set-up that usually apply high level of compressive stresses. Further, the existing analytical model of wicking characteristics of AGM separators has been extended to account for 3D characteristics, and subsequently, compared with the experimental results. A good agreement between the theory and experiments pave the way to simulate the realistic charge-discharge modes of the battery by applying cyclic loading condition. A threshold criterion describing the invariant behavior of pore size and wicking characteristics in terms of maximum permissible limit of key structural parameters during charge-discharge mode of the battery has also been proposed.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Battery Technologies Research · Advanced Battery Materials and Technologies · Advancements in Battery Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (48)
Show source-provided references
1. Why do batteries fail?10.1126/science.1253292 ↗
2. Micro-structural design and function of an improved absorptive glass mat (AGM) separator for valve-regulated lead–acid batteries10.1016/S0378-7753(01)01005-9 ↗
3. Pressure influence on the structural characteristics of modified absorptive glass mat separators: a standard contact porosimetry study10.1016/j.jpowsour.2015.04.175 ↗
4. Characterisation of separator papers for use in valve regulated lead/acid batteries10.1016/S0378-7753(01)00925-9 ↗
5. Essential characteristics for separators in valve-regulated lead–acid batteries10.1016/S0378-7753(02)00315-4 ↗
6. Saturation influences on the performance of valve-regulated lead–acid batteries10.1016/j.jpowsour.2004.10.013 ↗
7. Separator design for valve-regulated lead/acid batteries10.1016/0378-7753(94)01982-2 ↗
8. Pore size distribution of hybrid nonwoven geotextiles10.1016/j.geotexmem.2010.12.006 ↗
9. Investigation of the porous structure of battery separators using various porometric methods10.1016/j.jpowsour.2005.11.006 ↗
10. Part II: capillary size distribution10.1177/004051755802800207 ↗
11. Aerosol filters—pore size distribution in fibrous filters10.1016/0009-2509(67)80068-X ↗
12. A multiplanar model for the pore radius distribution in isotropic near-planar stochastic fibre networks10.1023/A:1023298820390 ↗
13. Theoretical and experimental opening sizes of heat-bonded geotextiles10.1177/004051758905900404 ↗
14. Granular filters and geotextile filters
15. Particle sieving in a random fiber network10.1016/S0307-904X(99)00055-4 ↗
16. Simulation of non-woven fibre mats and the application to coalescers10.1016/0009-2509(85)85052-1 ↗
17. “Density/solidity”of recombinant battery separator material—its influence on both separator and battery performance in valve-regulated lead- acid systems10.1016/j.jpowsour.2003.12.024 ↗
18. Amersorb: a new high-performance polymeric separator for lead–acid batteries10.1016/j.jpowsour.2004.10.021 ↗
19. Rate of capillary ascension of liquids10.1007/BF01461107 ↗
20. The dynamics of capillary flow10.1103/PhysRev.17.273 ↗
21. Amplification of electrolyte uptake in the absorptive glass mat (AGM) separator for valve regulated lead acid (VRLA) batteries10.1016/j.jpowsour.2016.11.027 ↗
22. An analytic solution of capillary rise restrained by gravity10.1016/j.jcis.2008.01.009 ↗
23. Investigation of the height and rate of capillary lift of electrolyte in the glass-mat separator of a sealed lead-acid battery10.1016/S0378-7753(02)00070-8 ↗
24. Fluid-transfer properties of recombinant battery separator media10.1016/S0378-7753(99)00508-X ↗
25. Effects of compression on recombinant battery separator mats in valve-regulated lead–acid batteries10.1016/S0378-7753(97)02782-1 ↗
26. Hutten · 2007
27. A review of physical properties of separators for valve-regulated lead/acid batteries10.1016/0378-7753(95)02313-5 ↗
28. Compression-recovery model of absorptive glass mat (AGM) separator guided by X-ray micro-computed tomography analysis10.1016/j.jpowsour.2017.08.055 ↗
29. Structural analysis of pore size distribution of nonwovens10.1080/00405000802442351 ↗
30. Effect of fiber orientation on pore size characteristics of nonwoven structures10.1002/app.32608 ↗
31. Modeling the compression-induced morphological behavior of nonwoven materials10.1007/s10853-011-6055-x ↗
32. Geometrical expressions of spaces in anisotropic fiber assemblies10.1177/004051757904900912 ↗
33. Pan · 2006
34. Estimation of fiber orientation and length in fiber assemblies10.1177/004051757804800601 ↗
35. Theoretical and experimental determination of the filtration opening size of geotextiles
36. Statistical geometry of pores and statistics of porous nanofibrous assemblies10.1098/rsif.2005.0039 ↗
37. Capillary pressure and liquid wicking in three-dimensional nonwoven materials10.1063/1.2965188 ↗
38. Compressional energy of the random fiber assembly part ii: evaluation10.1177/004051759206200502 ↗
39. Micromechanics of a planar hybrid fibrous network10.1177/004051759706701208 ↗
40. Liquid extrusion techniques for pore structure evaluation of nonwovens
41. Developments in absorptive glass mat separators for cycling applications and 36 V lead- acid batteries10.1016/j.jpowsour.2003.11.083 ↗
42. A modified porometry approach towards characterization of MF membranes10.1016/j.memsci.2012.07.005 ↗
43. The bubble gas transport method10.1016/B978-0-444-63776-5.00011-5 ↗
44. Relating recombination mat separator properties to sealed lead/acid battery performance10.1016/0378-7753(90)80061-H ↗
45. Charging strategies for valve-regulated lead/acid batteries in electric-vehicle applications10.1016/S0378-7753(97)02505-6 ↗
46. Effect of compression on the behaviour of lead-acid batteries10.1016/S0378-7753(00)00639-X ↗
47. Numbers of fiber-to-fiber contacts in general fiber assemblies10.1177/004051757704700104 ↗
48. Advanced separator construction for long life valve-regulated lead-acid batteries10.1016/S0378-7753(02)00688-2 ↗