Innovative design to improve the power density of a solid oxide fuel cell
Source abstract
Abstract
Abstract This paper explores the possibility of improving the power density of a solid oxide fuel cell (SOFC). A three-dimensional computational model (CFD-ACE package), with the relevant sub-models was used for the study. The performance of the SOFC was examined with a thin wall, which splits the inlet section and runs up to half the length of the flow channels. The results obtained with this (thin-walled) geometry were consistently better than those obtained with plain geometry (without the thin wall). The polarization characteristics of the thin-walled geometry indicated that the maximum power density obtained was 1.18 W cm −2 at an efficiency of around 60%. The corresponding values of maximum power density and the efficiency at which it was obtained for a plain geometry were 0.88 W cm −2 and 50%, respectively. The enhanced performance of the thin-walled geometry was attributed to a better distribution of the reactants along the length of the SOFC. Studies were also conducted to verify the performance of the thin-walled geometry over a wide range of inlet mass flow rates. They revealed a superior performance of the thin-walled geometry compared to the plain geometry. At lower inlet mass flow rates, the difference between the two in performance was small, but at higher inlet mass flow rates the difference in performance was significant.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advancements in Solid Oxide Fuel Cells · Fuel Cells and Related Materials · Electrocatalysts for Energy Conversion
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (25)
Show source-provided references
1. 2003 · vol. I
2. Modeling the performance of flattened tubular solid oxide fuel cell10.1115/1.1842783 ↗
3. SOFC power plants, the Siemens–Westinghouse approach10.1002/1615-6854(200105)1:1<78::AID-FUCE78>3.0.CO;2-Q ↗
4. Development of an auxiliary power unit with solid oxide fuel cells for automotive applications10.1002/fuce.200332107 ↗
5. SOFC technology development at Rolls-Royce10.1016/S0378-7753(99)00428-0 ↗
6. Solid State Energy Conversion Alliance, US Department of Energy, www.seca.doe.gov.
7. “Novel gas distributors and optimization for high power density in fuel cells”10.1016/j.jpowsour.2004.08.031 ↗
8. Improvement of anode performance by surface modification for solid oxide fuel cell running on hydrocarbon fuel10.1016/j.jpowsour.2004.05.002 ↗
9. Improvement of a single-chamber solid-oxide fuel cell and evaluation of new cell designs10.1149/1.1393359 ↗
10. Numerical simulation of heat transfer and fluid flow of a flat-tube high power density solid oxide fuel cell10.1115/1.1843120 ↗
11. Fabrication and characteristics of anode-supported flat-tube solid oxide fuel cell10.1016/S0378-7753(03)00431-2 ↗
12. A thermally self-sustained micro solid-oxide fuel-cell stack with high power density10.1038/nature03673 ↗
13. Singhal · 2003
14. Comparison of finite volume SOFC models for the simulation of a planar cell geometry10.1002/fuce.200400057 ↗
15. Current distribution measurements in a PEMFC with net flow geometry10.1023/B:JACH.0000015616.92074.5d ↗
16. Larminie · 2003
17. Evaluation and modeling of performance of anode-supported solid oxide fuel cell10.1016/S0378-7753(99)00444-9 ↗
18. Enhancements of the SIMPLE method for predicting incompressible fluid flows10.1080/01495728408961817 ↗
19. Patankar · 1980
20. CFD Research Corp., 2002. CFD-ACE(U)™User Manual, version 2002. Huntsville, Alabama.
21. Fuel composition and diluent effect on gas transport and performance of anode-supported SOFCs10.1149/1.1579480 ↗
22. Comparison of the performance of Cu–CeO2–YSZ and Ni–YSZ Composite SOFC Anodes With H2, CO, and Syngas10.1016/j.jpowsour.2004.09.022 ↗
23. Current–voltage characteristics and impedance analysis of solid oxide fuel cells for mixed H2 and CO gases10.1149/1.1435357 ↗
24. Performance evaluation of anode-supported solid oxide fuel cells with thin YSZ electrolyte10.1016/j.ijhydene.2004.01.009 ↗
25. Generalized model of planar SOFC repeat element for design optimization10.1016/j.jpowsour.2003.11.088 ↗