Effect of pressure and thermal management on stray currents in alkaline water electrolyser stacks
Source abstract
Abstract
Stray currents bypassing the active area through ports and manifolds decrease current efficiency in industrial alkaline water electrolysers (AWEs). The coupled electrical–thermal model for a 163-cell industrial stack quantifies how operating pressure and the inlet–outlet temperature difference ( Δ T ) affect stray-current losses, their inlet/outlet distribution, and current efficiency. Pressure influences conductivity through changes in void fraction and water-vapour formation. Thermal balance determines the inlet temperature and electrolyte flow rate to achieve a set Δ T . Increasing pressure compresses bubbles, reduces water-vapour mass flow, and increases outlet-side conductivity. This raises outlet-side stray-current losses, while the inlet-side share remains nearly constant. Raising Δ T lowers the inlet temperature and reduces the flow rate required to meet the outlet-temperature constraint, decreasing ionic conductivity at both the inlet and outlet. Thus, lowering pressure at fixed Δ T and raising Δ T at fixed pressure both reduce stray-current losses. Adjusting the electrolyte flow with input current can further suppress them. However, if the outlet void fraction saturates at 75 % (e.g., due to rapid gas removal), reducing pressure provides little additional benefit. In this case, the current-efficiency plateau occurs near 10 bar(a). This analysis highlights the need to manage both pressure and Δ T to design and control high-efficiency AWE stacks.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Hybrid Renewable Energy Systems · Electrocatalysts for Energy Conversion · Integrated Energy Systems Optimization
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (34)
Show source-provided references
1. Alkaline water electrolysis powered by renewable energy: a review10.3390/pr8020248 ↗
2. Hydrogen energy — Abundant, efficient, clean: A debate over the energy-system-of-change10.1016/j.ijhydene.2009.05.063 ↗
3. Off-grid solar PV –wind power–battery–water electrolyzer plant: Simultaneous optimization of component capacities and system control10.1016/j.apenergy.2023.121277 ↗
4. Dynamic energy and mass balance model for an industrial alkaline water electrolyzer plant process10.1016/j.ijhydene.2021.11.126 ↗
5. Sensitivity analysis of the process conditions affecting the shunt currents and the SEC in an industrial-scale alkaline water electrolyzer plant10.1016/j.apenergy.2024.122732 ↗
6. Modelling and study of shunt currents in an industrial alkaline water electrolyser with various number of cells in series10.1049/rpg2.70112 ↗
7. Dynamic mass- and energy-balance simulation model of an industrial-scale atmospheric alkaline water electrolyzer10.1016/j.energy.2025.135602 ↗
8. Current leakage through cascaded cells10.1149/1.3071420 ↗
9. Channel design optimization of alkaline electrolysis stacks considering the trade-off between current efficiency and pressure drop10.1016/j.jpowsour.2023.233222 ↗
10. Prediction of shunt currents in a bipolar electrolyzer stack by difference calculus10.1007/s10800-007-9330-4 ↗
11. Experimental and modeling study on energy flow of 250 kW alkaline water electrolysis system under steady state conditions and cold start process10.1016/j.fuel.2023.128799 ↗
12. Model based examination on influence of stack series connection and pipe diameters on efficiency of vanadium redox flow batteries under consideration of shunt currents10.1016/j.jpowsour.2015.01.119 ↗
13. A multi-stack simulation of shunt currents in vanadium redox flow batteries10.1016/j.jpowsour.2014.03.054 ↗
14. Shunt current analysis of vanadium redox flow battery system with multi-stack connections10.1016/j.est.2023.109233 ↗
15. Analysis of shunt currents and associated corrosion of bipolar plates in PEM fuel cells10.1016/j.jelechem.2014.09.009 ↗
16. Predicting shunt currents in stacks of bipolar plate cells10.1149/1.2108606 ↗
17. Predicting shunt currents in stacks of bipolar plate cells with conducting manifolds10.1149/1.2096069 ↗
18. Experimental determination and calculation of parasitic currents in bipolar electrolyzers with application to chlorate electrolyzer10.1149/1.2401878 ↗
19. Current losses in a bipolar cell — ii: An analysis of the Butler–Volmer regime10.1016/S0013-4686(98)00002-4 ↗
20. Optimal operating parameters for advanced alkaline water electrolysis10.1016/j.ijhydene.2022.08.075 ↗
21. Optimal configuration and pressure levels of electrolyzer plants in context of power-to-gas applications10.1016/j.apenergy.2016.01.038 ↗
22. Advanced pressurized alkaline water electrolysis at high temperatures up to 130 °C10.1016/j.ijhydene.2025.150075 ↗
23. Numerical modeling and analysis of the effect of pressure on the performance of an alkaline water electrolysis system10.1016/j.apenergy.2021.116554 ↗
24. A review of specific conductivities of potassium hydroxide solutions for various concentrations and temperatures10.1016/j.ijhydene.2006.10.062 ↗
25. Holman · 2001
26. 2007
27. Vogt · 2014 · 1
28. 2008
29. Ishii · 2011
30. Void fraction and current density distributions in a water electrolysis cell10.1149/1.2411770 ↗
31. Bubble effects on the solution IR drop in a vertical electrolyzer under free and forced convection10.1149/1.2129658 ↗
32. Existence of optimum space between electrodes on hydrogen production by water electrolysis10.1016/S0360-3199(02)00027-7 ↗
33. Ghajar · 2020
34. The effect of pipe diameter on the structure of gas/liquid flow in vertical pipes10.1016/j.ijmultiphaseflow.2009.11.010 ↗