Determination of temperature distribution of a solid oxide cell stack using regenerated fiber Bragg gratings
Source abstract
Abstract
The temperature distributions inside the solid oxide cell (SOC) stacks are conventionally monitored using thermocouples. Despite their reliability, employing a large number of thermocouples is often not practical due to their electrical conductivity and significant cabling effort. In this work, an optical fiber with an array of seven regenerated fiber Bragg grating (RFBG) sensors was integrated into a modified Jülich F10 solid oxide cell stack to address these challenges. The transient temperature profiles during heat-up and current–voltage characterization, as well as the steady state profiles during fuel cell operation under varying conditions were recorded using both the RFBG sensors and nine type-N thermocouples. The RFBG sensors provided accurate, localized temperature measurement up to 800 °C in the stack. Based on the recorded temperature profiles, the underlying causes for thermal gradient and heat dissipation of this five-layer SOC stack were analyzed and stack operating strategies were discussed. This study demonstrated the feasibility and advantages of using RFBG sensors in SOC applications and established previously inaccessible boundary conditions for stack level simulation work. • RFBG sensors conduct multipoint temperature measurement in a SOC stack. • Asynchronous heating of the stack caused thermal gradient during heat up. • RFBG sensors are more suitable for capturing transient temperature changes. • Significant temperature change during IV curve leads to incorrect estimation of ASR. • Heat conduction dominates the heat dissipation during fuel cell operation.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Gas Sensing Nanomaterials and Sensors · Advanced Fiber Optic Sensors · Transition Metal Oxide Nanomaterials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (47)
Show source-provided references
1. Performance benchmark of planar solid oxide cells based on material development and designs10.1002/ente.202001062 ↗
2. A review on solid oxide fuel cell durability: Latest progress, mechanisms, and study tools10.1016/j.rser.2022.112339 ↗
3. Analysis of solid oxide fuel and electrolysis cells operated in a real-system environment: State-of-the-health diagnostic, failure modes, degradation mitigation and performance regeneration10.1016/j.pecs.2022.101011 ↗
4. Solid oxide fuel cells (sofcs): a review of an environmentally clean and efficient source of energy10.1016/S1364-0321(02)00014-X ↗
5. Degradation analysis of an sofc short stack subject to 10,000 h of operation10.1149/1945-7111/abc843 ↗
6. Department of Energy · 2025
7. Acceleration tests: Degradation of anode-supported planar solid oxide fuel cells at elevated operating temperatures10.1016/j.jpowsour.2017.06.004 ↗
8. The influence of sulfur impurities in industrial cox gases on solid oxide electrolysis cell (soec) degradation10.1016/j.jpowsour.2023.232669 ↗
9. Origin of steam contaminants and degradation of solid-oxide electrolysis stacks10.3390/pr10030598 ↗
10. Ni migration in solid oxide cell electrodes: Review and revised hypothesis10.1002/fuce.202100072 ↗
11. Degradation mechanisms of solid oxide fuel cells under various thermal cycling conditions10.1021/acsami.1c13779 ↗
12. Study of solid oxide electrolysis cells operated in potentiostatic mode: Effect of operating temperature on durability10.1016/j.cej.2021.129260 ↗
13. Post-test characterization of a solid oxide fuel cell after more than 10 years of stack testing10.1016/j.jpowsour.2020.228770 ↗
14. Stack degradation in dependence of operation parameters; the real-sofc sensitivity analysis10.1002/fuce.200800146 ↗
15. Simulation of thermal stresses in anode-supported solid oxide fuel cell stacks. part i: Probability of failure of the cells10.1016/j.jpowsour.2008.12.050 ↗
16. Simulation of thermal stresses in anode-supported solid oxide fuel cell stacks. part ii: Loss of gas-tightness, electrical contact and thermal buckling10.1016/j.jpowsour.2008.12.039 ↗
17. Thermo-electrochemical and thermal stress analysis for an anode-supported sofc cell10.1016/j.renene.2008.02.023 ↗
18. Experimental investigation of temperature distribution over a planar solid oxide fuel cell10.1016/j.apenergy.2012.12.062 ↗
19. Measurement of the temperature distribution in a large solid oxide fuel cell short stack10.1016/j.ijhydene.2013.06.024 ↗
20. Durability test and degradation behavior of a 2.5 kw sofc stack with internal reforming of lng10.1016/j.ijhydene.2013.09.140 ↗
21. A nonlinear sliding mode observer for the estimation of temperature distribution in a planar solid oxide fuel cell10.1016/j.ijhydene.2014.10.117 ↗
22. Cell integrated multi-junction thermocouple array for solid oxide fuel cell temperature sensing: N+1 architecture10.1016/j.jpowsour.2016.03.002 ↗
23. In-situ monitoring of temperature distribution in operating solid oxide fuel cell cathode using proprietary sensory techniques versus commercial thermocouples10.1016/j.apenergy.2018.08.120 ↗
24. Parameters and their impacts on the temperature distribution and thermal gradient of solid oxide fuel cell10.1016/j.apenergy.2019.03.034 ↗
25. Performance and durability of thin film thermocouple array on a porous electrode
26. Application of infrared thermal imaging to the study of pellet solid oxide fuel cells10.1016/j.jpowsour.2006.12.098 ↗
27. Real-time thermal imaging of solid oxide fuel cell cathode activity in working condition10.1364/AO.55.007142 ↗
28. Investigating the effect of thermal gradients on stress in solid oxide fuel cell anodes using combined synchrotron radiation and thermal imaging10.1016/j.jpowsour.2015.04.104 ↗
29. Optical fiber sensors for high-temperature monitoring: A review
30. Distributed fiber sensors with high spatial resolution in extreme radiation environments in nuclear reactor cores10.1109/JLT.2021.3075630 ↗
31. Distributed optical fiber sensors with ultrafast laser enhanced rayleigh backscattering profiles for real-time monitoring of solid oxide fuel cell operations10.1038/s41598-017-09934-3 ↗
32. Regenerated fibre bragg gratings: A critical assessment of more than 20 years of investigations10.1016/j.optlastec.2020.106650 ↗
33. Generalized and wavelength-dependent temperature calibration function for multipoint regenerated fiber bragg grating sensors10.1364/OE.470093 ↗
34. In-fibre bragg grating sensors10.1088/0957-0233/8/4/002 ↗
35. Multiplexed regenerated fiber bragg gratings for high-temperature measurement10.1088/0957-0233/24/9/094010 ↗
36. Regenerated bragg grating sensor array for temperature measurements during an aluminum casting process10.1109/JSEN.2018.2837164 ↗
37. Fiber-optic multipoint sensor system with low drift for the long-term monitoring of high-temperature distributions in chemical reactors
38. In-situ high temperature and large strain monitoring during a copper casting process based on regenerated fiber bragg grating sensors10.1109/JLT.2021.3101524 ↗
39. Performance and degradation of solid oxide electrolysis cells in stack10.1149/2.0941508jes ↗
40. Performance and degradation of an soec stack with different cell components10.1016/j.electacta.2017.11.180 ↗
41. Electrochemical performance and degradation analysis of an sofc short stack following operation of more than 100, 000 hours10.1149/2.0751916jes ↗
42. MathWorks · 2025
43. Sofc stack performance under high fuel utilization10.1016/j.ijhydene.2014.11.094 ↗
44. A novel flow field design with flow re-distribution for advanced thermal management in solid oxide fuel cell10.1016/j.apenergy.2022.120364 ↗
45. Multiphysical modelling of planar solid oxide fuel cell stack layers10.1016/j.jpowsour.2019.227552 ↗
46. Heat transfer
47. VDM Metals International GmbH · 2025