Chemo-thermal stress in all-solid-state batteries: Impact of cathode active materials and microstructure
Source abstract
Abstract
The transition from conventional lithium-ion to all-solid-state lithium batteries (ASSBs) promises enhanced safety and higher energy density but also gives rise to new challenges, like capacity degradation due to enhanced mechanical stresses. This study addresses the often-overlooked residual (thermal) mechanical stress arising during manufacturing, which can significantly contribute to the overall mechanical stress. While stress evolution during battery operation is often only associated with the de-/lithiation-induced stresses from the active material, we introduce a “chemo-thermal stress” description. By this integration of thermal and chemical stresses, we developed a more accurate level to simulate real-life conditions, especially for all-solid-state batteries. This holistic approach demonstrated for the first time, that thermal stresses from manufacturing can reduce the induced mechanical stress in LiCoO 2 (LCO) during delithiation, resulting in the total chemo-thermal stress being approximately 43 % lower. In contrast, residual thermal stress exacerbates chemical stress in Li 0.5 NCM955 and Li 0.1 NCM955, leading to a principal stress increases of approximately 42 % and 15 %, respectively. We also examine the impact of microstructural design parameters, particularly the solid volume fraction of the cathode active material (CAM) and relative density, on the induced mechanical stresses within CAM and the solid electrolyte (SE). Our investigation reveals that the volume change in cathode active materials, a primary contributor to induced mechanical stress in ASSBs, is not a reliable factor for predicting final stresses in actual full battery cells. Additionally, our findings highlight LCO's superior mechanical behavior compared to Li 0.5 NCM955 and Li 0.1 NCM955, attributed to lower overall stress and prevalent compressive stress, which mitigates failure risks in oxide materials. • Chemo-thermal stress includes thermal and chemical stresses. • Thermal stress significantly impacts Chemo-thermal stress in ASSBs. • LCO shows ∼43 % lower chemo-thermal stress than chemical stress. • Li 0.5 NCM955 and Li 0.1 NCM955 show ∼42 % and ∼15 % higher chemo-thermal stresses. • CAM volume change is not a reliable indicator of mechanical stress levels.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Advancements in Battery Materials · Advanced Battery Materials and Technologies · Advanced Battery Technologies Research
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (73)
Show source-provided references
1. High capacity garnet-based all-solid-state lithium batteries: fabrication and 3D-microstructure resolved modeling10.1021/acsami.8b06705 ↗
2. Enhancement of the Li+ conductivity of Li3AlF6 for stable all-solid-state lithium-ion batteries10.1021/acsaem.4c00115 ↗
3. Review—practical challenges hindering the development of solid state Li ion batteries10.1149/2.1571707jes ↗
4. A solid future for battery development10.1038/nenergy.2016.141 ↗
5. Composite polymer electrolytes with Li7La3Zr2O12 garnet-type nanowires as ceramic fillers: mechanism of conductivity enhancement and role of doping and morphology10.1021/acsami.7b03806 ↗
6. Investigating the dendritic growth during full cell cycling of garnet electrolyte in direct contact with Li metal10.1021/acsami.6b13925 ↗
7. Grain boundary modification to suppress lithium penetration through garnet-type solid electrolyte10.1016/j.jpowsour.2017.07.088 ↗
8. Characterizing the Li–Li7La3Zr2O12 interface stability and kinetics as a function of temperature and current density10.1016/j.jpowsour.2015.10.053 ↗
9. Interphase formation on lithium solid electrolytes—an in situ approach to study interfacial reactions by photoelectron spectroscopy10.1016/j.ssi.2015.06.001 ↗
10. Impedance characterization reveals mixed conducting interphases between sulfidic superionic conductors and lithium metal electrodes10.1016/j.jpowsour.2017.03.103 ↗
11. Direct observation of the interfacial instability of the fast ionic conductor Li10GeP2S12 at the lithium metal anode10.1021/acs.chemmater.6b00610 ↗
12. Modeling and simulation of 2D lithium-ion solid state battery10.1002/er.3344 ↗
13. The effect of stress on battery-electrode capacity10.1149/2.0371704jes ↗
14. Modeling of internal mechanical failure of all-solid-state batteries during electrochemical cycling, and implications for battery design10.1039/C7TA03199H ↗
15. Deformation and stress in electrode materials for Li-ion batteries10.1016/j.pmatsci.2014.02.001 ↗
16. Interfacial incompatibility and internal stresses in all-solid-state lithium ion batteries10.1002/aenm.201901810 ↗
17. Fracture behavior in battery materials
18. Lithium intercalation cells without metallic lithium: and10.1149/1.2100521 ↗
19. Nagaura · 1990 · vol. 9 · 209
20. Characterization of thin‐film rechargeable lithium batteries with lithium cobalt oxide cathodes10.1149/1.1837188 ↗
21. High capacity surface-modified LiCoO2 cathodes for lithium-ion batteries10.1149/1.1526782 ↗
22. Electrochemical stability of thin-film LiCoO2 cathodes by aluminum-oxide coating10.1021/cm0201403 ↗
23. Cathode materials review10.1063/1.4878478 ↗
24. Favorable electrochemical performance of LiMn2O4/LiFePO4 composite electrodes attributed to composite solid electrolytes for all-solid-state lithium batteries10.1021/acs.langmuir.0c03274 ↗
25. Exploiting the degradation mechanism of NCM523 graphite lithium‐ion full cells operated at high voltage10.1002/cssc.202002113 ↗
26. High-rate layered cathode of lithium-ion batteries through regulating three-dimensional agglomerated structure10.3390/en13071602 ↗
27. Between scylla and charybdis: balancing among structural stability and energy density of layered NCM cathode materials for advanced lithium-ion batteries10.1021/acs.jpcc.7b06363 ↗
28. High-capacity layered cathodes for next-generation electric vehicles10.1021/acsenergylett.9b00652 ↗
29. Improve safety of high energy density LiNi1/3Co1/3Mn1/3O2/graphite battery using organosilicon electrolyte10.1016/j.electacta.2018.11.036 ↗
30. A method of increasing the energy density of layered Ni-rich Li[Ni1−2xCoxMnx]O2 cathodes (x = 0.05, 0.1, 0.2)10.1039/C8TA10438G ↗
31. Layered cathode materials Li [Nix Li (1/3 − 2x/3) Mn (2/3 − x/3)] O 2 for lithium-ion batteries10.1149/1.1407994 ↗
32. Novel lithium insertion material of LiCo1/3Ni1/3Mn1/3O2 for advanced lithium-ion batteries10.1016/S0378-7753(03)00173-3 ↗
33. High-voltage positive electrode materials for lithium-ion batteries10.1039/C6CS00875E ↗
34. Nickel‐rich and lithium‐rich layered oxide cathodes: progress and perspectives10.1002/aenm.201501010 ↗
35. Comparative study of the electrochemical performance of LiNi0.5Co0.2Mn0.3O2 and LiNi0.8Co0.1Mn0.1O2 cathode materials for lithium ion batteries10.1016/j.ssi.2018.10.020 ↗
36. Thermal analysis of nickel cobalt lithium manganese with varying nickel content used for lithium ion batteries10.1016/j.tca.2017.06.022 ↗
37. Preparation of hierarchical LiNixCoyMnzO2 from solvothermal [NixCoyMnz](OH) 2 via regulating the ratio of Ni, Co, and Mn and its excellent properties for lithium‐ion battery cathode10.1002/jccs.202000051 ↗
38. High-rate cycling performance and surface analysis of LiNi1-xCox/2Mnx/2O2 (x=2/3, 0.4, 0.2) cathode materials, Mater
39. Review on oxygen release mechanism and modification strategy of nickel-rich NCM cathode materials for lithium-ion batteries: recent advances and future directions10.1021/acs.energyfuels.3c04636 ↗
40. Fast lithium ion conduction in garnet-type Li7La3Zr2O1210.1002/anie.200701144 ↗
41. High conductivity of mixed phase Al-substituted Li7La3Zr2O1210.1007/s10832-015-9988-7 ↗
42. Structure and dynamics of the fast lithium ion conductor “Li 7 La 3 Zr 2 O 12”10.1039/c1cp22108f ↗
43. Li7La3Zr2O12 interface modification for Li dendrite prevention10.1021/acsami.6b00831 ↗
44. Temperature effects on cycling stability of Li plating/stripping on Ta-doped Li7La3Zr2O1210.1016/j.jpowsour.2017.01.009 ↗
45. Crystal chemistry and stability of “Li7La3Zr2O12” garnet: a fast lithium-ion conductor10.1021/ic101914e ↗
46. Cubic phases of garnet-type Li 7 La 3 Zr 2 O 12: the role of hydration10.1039/c3ta11996c ↗
47. About the compatibility between high voltage spinel cathode materials and solid oxide electrolytes as a function of temperature10.1021/acsami.6b09059 ↗
48. Chemical compatibility between garnet-like solid state electrolyte Li6. 75La3Zr1. 75Ta0. 25O12 and major commercial lithium battery cathode materials10.1016/j.jmat.2016.04.003 ↗
49. Cathode-electrolyte material interactions during manufacturing of inorganic solid-state lithium batteries10.1007/s10832-016-0062-x ↗
50. First-principles studies on cation dopants and Electrolyte|Cathode interphases for lithium garnets10.1021/acs.chemmater.5b01023 ↗
51. Mechanism study on the interfacial stability of a lithium garnet-type oxide electrolyte against cathode materials10.1021/acsaem.8b01035 ↗
52. Solid-state Li–metal batteries: challenges and horizons of oxide and sulfide solid electrolytes and their interfaces
53. All-solid-state Li batteries with NCM–garnet-based composite cathodes: the impact of NCM composition on material compatibility10.1021/acsaem.2c00533 ↗
54. Impact of Ni–Mn–Co–Al-based cathode material composition on the sintering with garnet solid electrolytes for all-solid-state batteries10.1021/acs.chemmater.3c01573 ↗
55. Microstructural parameters governing the mechanical stress and conductivity of all-solid-state lithium-ion-battery cathodes10.1016/j.est.2023.107784 ↗
56. The influence of hafnium impurities on the electrochemical performance of tantalum substituted Li7La3Zr2O12 solid electrolytes10.1007/s11581-021-04300-w ↗
57. Evaluation of scalable synthesis methods for aluminum-substituted Li7La3Zr2O12 solid electrolytes10.3390/ma14226809 ↗
58. A sinter-free future for solid-state battery designs10.1039/D2EE00279E ↗
59. Modelling electro-chemical induced stresses in all-solid-state batteries: anisotropy effects in cathodes and cell design optimisation10.1016/j.jpowsour.2020.229430 ↗
60. A new algorithm for three-dimensional Voronoi tessellation10.1016/0021-9991(83)90087-6 ↗
61. BB: an R package for solving a large system of nonlinear equations and for optimizing a high-dimensional nonlinear objective function
62. Projector augmented-wave method10.1103/PhysRevB.50.17953 ↗
63. Efficient iterative schemes for ab initio total-energy calculations using a plane-wave basis set10.1103/PhysRevB.54.11169 ↗
64. Generalized gradient approximation made simple10.1103/PhysRevLett.77.3865 ↗
65. Phase-field modeling of stress generation in polycrystalline LiCoO210.1016/j.ssi.2018.02.013 ↗
66. Modelling electro-chemically induced stresses in all-solid-state batteries: screening electrolyte and cathode materials in composite cathodes10.1039/D3TA01729J ↗
67. Mechanical properties of the solid electrolyte Al-substituted Li7La3Zr2O12 (LLZO) by utilizing micro-pillar indentation splitting test10.1016/j.jeurceramsoc.2018.02.032 ↗
68. Room temperature elastic moduli and Vickers hardness of hot-pressed LLZO cubic garnet10.1007/s10853-012-6687-5 ↗
69. Elastic properties of the solid electrolyte Li7La3Zr2O12 (LLZO)10.1021/acs.chemmater.5b03854 ↗
70. Effect of pressure on the structural properties and Raman modes of ${\mathrm{LiCoO}}_{210.1103/PhysRevB.72.224102 ↗
71. Structure and electron density analysis of electrochemically and chemically delithiated LiCoO2 single crystals10.1016/j.jssc.2006.10.018 ↗
72. A numerical method for computing the overall response of nonlinear composites with complex microstructure10.1016/S0045-7825(97)00218-1 ↗
73. Computational homogenization of elasticity on a staggered grid10.1002/nme.5008 ↗