A comparative study on the influence of the polymeric host for the operation of all-solid-state batteries at different temperatures
Source abstract
Abstract
Solid Polymer Electrolytes (SPE) are critical components to develop safe, high energy density all solid-state lithium metal batteries (ASSB), providing favorable mechanical properties and good stability vs Li-metal. Typically used poly(ethylene oxide) (PEO) based electrolytes do not allow cycling of all solid-state cells at room temperature due to the crystallization of PEO hindering the ionic transport. Increasing the ionic conductivity of SPE at lower temperature is then mandatory. This study addresses the challenge thanks to the use of Polymerized ionic liquid (PIL), poly(diallyldimethylammonium) bis(trifluoromethanesulfonyl)imide (PDADMAT) as polymeric host for producing SPE. Mixtures of PDADMAT and PEO with tetraglyme Li salt IL, LiG4TFSI, are prepared and their electrochemical properties in lithium metal batteries investigated. Through composition optimization, membranes containing 66 wt % of LiG4TFSI were selected as the best compromise in term of conduction properties (above 10 −4 S/cm at room temperature), transference number of ca. 0.4 and mechanical behavior. All-solid-state cells prepared using PDADMAT-based membranes were able to cycle at 60 °C and room temperature up to 0.425 mA/cm 2 current densities whereas POE-based cells could only sustain 60 °C cycling. The study underlines the benefit of using IL and PIL as components of SPE for the operation of high performance ASSB at room temperature.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Battery Materials and Technologies · Advancements in Battery Materials · Advanced Battery Technologies Research
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (89)
Show source-provided references
1. Toward safe lithium metal anode in rechargeable batteries: a review10.1021/acs.chemrev.7b00115 ↗
2. High rate and stable cycling of lithium metal anode10.1038/ncomms7362 ↗
3. Lithium metal anodes for rechargeable batteries10.1039/C3EE40795K ↗
4. A short review of failure mechanisms of lithium metal and lithiated graphite anodes in liquid electrolyte solutions10.1016/S0167-2738(02)00080-2 ↗
5. Polymer electrolytes for lithium polymer batteries10.1039/C6TA02621D ↗
6. Challenges and prospects of the role of solid electrolytes in the revitalization of lithium metal batteries10.1039/C6TA07384K ↗
7. Single lithium-ion conducting solid polymer electrolytes: advances and perspectives10.1039/C6CS00491A ↗
8. Composite polymer electrolytes reinforced by two-dimensional layer-double-hydroxide nanosheets for dendrite-free lithium batteries10.1016/j.ssi.2020.115275 ↗
9. Poly(ethylene oxide)-based electrolytes for lithium-ion batteries10.1039/C5TA03471J ↗
10. BlueStorage, B.
11. Issues and challenges facing rechargeable lithium batteries10.1038/35104644 ↗
12. Single-ion diblock copolymers for solid-state polymer electrolytes10.1016/j.polymer.2015.04.056 ↗
13. Salt-concentration dependence of the glass transition temperature in PEO–NaI and PEO–LiTFSI polymer electrolytes10.1021/ma401686r ↗
14. Complexes of lithium imide salts with tetraglyme and their polyelectrolyte composite materials10.1149/1.1635384 ↗
15. Promising routes to a high Li+ transference number electrolyte for lithium ion batteries10.1021/acsenergylett.7b00792 ↗
16. The importance of the lithium ion transference number in lithium/polymer cells10.1016/0013-4686(94)85091-7 ↗
17. Why are ionic liquids liquid? A simple explanation based on lattice and solvation energies10.1021/ja0619612 ↗
18. Why are ionic liquids liquid? A simple explanation based on lattice and solvation energies10.1021/ja0619612 ↗
19. Ionic liquid-based electrolytes for energy storage devices: a brief review on their limits and applications10.3390/polym12040918 ↗
20. Recent advances in innovative polymer electrolytes based on poly(ionic liquid)s10.1016/j.electacta.2015.03.038 ↗
21. Ionic-liquid-based polymer electrolytes for battery applications10.1002/anie.201504971 ↗
22. Polymeric ionic liquids: broadening the properties and applications of polyelectrolytes10.1016/j.progpolymsci.2011.05.007 ↗
23. Recent advances in solid-state polymer electrolytes and innovative ionic liquids based polymer electrolyte systems10.1016/j.coelec.2020.01.015 ↗
24. Synthesis of pyrrolidinium-based poly(ionic liquid) electrolytes with poly(ethylene glycol) side chains10.1021/cm203790z ↗
25. Ionic liquids in electrochemical energy storage10.1016/j.coelec.2018.03.005 ↗
26. Application of ionic liquids to energy storage and conversion materials and devices10.1021/acs.chemrev.6b00504 ↗
27. Designing all-polymer nanostructured solid electrolytes: advances and prospects10.1021/acsomega.9b04098 ↗
28. Sustainable, dendrite free lithium-metal electrode cycling achieved with polymer composite electrolytes based on a poly(ionic liquid) host10.1002/batt.201800120 ↗
29. Pyrrolidinium-based polymeric ionic liquids as mechanically and electrochemically stable polymer electrolytes10.1016/j.jpowsour.2008.11.115 ↗
30. Preparation and characterization of gel polymer electrolytes using poly(ionic liquids) and high lithium salt concentration ionic liquids10.1039/C7TA08233A ↗
31. Poly(Ionic liquid)s-in-salt electrolytes with Co-coordination-Assisted lithium-ion transport for safe batteries10.1016/j.joule.2019.07.008 ↗
32. The anion effect in ternary electrolyte systems using poly(diallyldimethylammonium) and phosphonium-based ionic liquid with high lithium salt concentration10.1016/j.ssi.2018.10.018 ↗
33. Poly(Ionic liquid)-based composite gel electrolyte for lithium batteries10.1002/celc.201900504 ↗
34. Polymeric ionic liquid gel electrolyte for room temperature lithium battery applications10.1016/j.electacta.2016.07.118 ↗
35. Enhanced transport and favorable distribution of Li-ion in a poly(ionic liquid) based electrolyte facilitated by Li1.3Al0.3Ti1.7(PO4)3 nanoparticles for highly-safe lithium metal batteries10.1016/j.electacta.2020.137581 ↗
36. Enhancing cation diffusion and suppressing anion diffusion via lewis-acidic polymer electrolytes10.1021/acs.jpclett.6b02662 ↗
37. Designing polymer electrolytes for safe and high capacity rechargeable lithium batteries10.1021/acs.accounts.6b00568 ↗
38. Polymer-in-“Quasi-Ionic liquid” Electrolytes for high-voltage lithium metal batteries10.1002/aenm.201902108 ↗
39. Quasi-ionic liquid enabling single-phase poly(vinylidene fluoride)-based polymer electrolytes for solid-state LiNi0.6Co0.2Mn0.2O2||Li batteries with rigid-flexible coupling interphase10.1002/smtd.202100262 ↗
40. Li+ ion transport in polymer electrolytes based on a glyme-Li salt solvate ionic liquid10.1016/j.electacta.2015.01.067 ↗
41. Polymer electrolytes containing solvate ionic liquids: a new approach to achieve high ionic conductivity, thermal stability, and a wide potential window10.1021/acs.chemmater.7b04274 ↗
42. Chemical sensor systems based on 2D and thin film materials10.1088/2053-1583/ab6e88 ↗
43. Physicochemical properties of glyme–Li salt complexes as a new family of room-temperature ionic liquids10.1246/cl.2010.753 ↗
44. Oxidative-stability enhancement and charge transport mechanism in glyme–lithium salt equimolar complexes10.1021/ja203983r ↗
45. Ionic conductivity studies of polymeric electrolytes containing lithium salt with plasticizer10.1016/j.electacta.2004.01.101 ↗
46. Ionic liquid doped PEO-based solid polymer electrolytes for lithium-ion polymer batteries10.1016/j.ijhydene.2016.04.160 ↗
47. PEO-based polymer electrolytes with ionic liquids and their use in lithium metal-polymer electrolyte batteries10.1149/1.1890701 ↗
48. Ionic liquid-based electrolyte Membranes for medium-high temperature lithium polymer batteries10.3390/membranes8030041 ↗
49. Water content in solid polymer electrolytes: the lost knowledge10.1039/D0CC03556D ↗
50. The impact of absorbed solvent on the performance of solid polymer electrolytes for use in solid-state lithium batteries10.1016/j.isci.2020.101597 ↗
51. On the importance of Li metal morphology on the cycling of lithium metal polymer cells10.1149/1945-7111/abf017 ↗
52. Phase diagrams and conductivity behavior of poly(ethylene oxide)-molten salt rubbery electrolytes10.1021/ma00103a034 ↗
53. Lithium dendrite growth mechanisms in polymer electrolytes and prevention strategies10.1039/C7CP03304D ↗
54. Correction: lithium dendrite growth mechanisms in polymer electrolytes and prevention strategies10.1039/D0CP90011G ↗
55. Thermal transitions in and structures of dried polyelectrolytes and polyelectrolyte complexes10.1002/polb.24319 ↗
56. Effect of temperature and composition on the transport and thermodynamic properties of binary mixtures of ionic liquid N-butyl-N-methylpyrrolidinium bis(trifluoromethanesulfonyl)imide and propylene carbonate10.1007/s10953-010-9562-5 ↗
57. Distinct difference in ionic transport behavior in polymer electrolytes depending on the matrix polymers and incorporated salts10.1021/jp045328j ↗
58. Polymer electrolytes: ionic transport mechanisms and relaxation coupling10.1557/mrs2000.16 ↗
59. Extrusion of polymer blend electrolytes for solid-state lithium batteries: a study of polar functional groups10.1021/acsapm.1c01466 ↗
60. Ternary polymer electrolytes containing pyrrolidinium-based polymeric ionic liquids for lithium batteries10.1016/j.jpowsour.2009.11.146 ↗
61. A quantitative study of gravity-induced convection in two-dimensional parallel electrodeposition cells10.1016/0022-0728(95)04477-9 ↗
62. Shape evolution of metals electrodeposited from binary electrolytes10.1016/S0022-0728(02)01269-X ↗
63. Solvent effects on Li ion transference number and dynamic ion correlations in glyme- and sulfolane-based molten Li salt solvates10.1039/D0CP02181D ↗
64. Effect of salt concentration on ion clustering and transport in polymer solid electrolytes: a molecular dynamics study of PEO–LiTFSI10.1021/acs.chemmater.8b01955 ↗
65. Direct determination of ionic transference numbers in ionic liquids by electrophoretic NMR10.1039/C5CP05753A ↗
66. Negative effective Li transference numbers in Li salt/ionic liquid mixtures: does Li drift in the “Wrong” direction?10.1039/C7CP08580J ↗
67. Comment on “Negative effective Li transference numbers in Li salt/ionic liquid mixtures: does Li drift in the “Wrong” direction?” by M. Gouverneur, F. Schmidt and M. Schönhoff, Phys. Chem. Chem. Phys., 2018, 20, 747010.1039/C8CP02595A ↗
68. Reply to the ‘Comment on “Negative effective Li transference numbers in Li salt/ionic liquid mixtures: does Li drift in the “Wrong” direction?”’ by K. R. Harris
69. Correction: comment on “Negative effective Li transference numbers in Li salt/ionic liquid mixtures: does Li drift in the “Wrong” direction?” by M. Gouverneur, F. Schmidt and M. Schönhoff, Phys. Chem. Chem. Phys., 2018, 20, 747010.1039/C8CP91941K ↗
70. Ion transport and the true transference number in nonaqueous polyelectrolyte solutions for lithium ion batteries10.1021/acscentsci.9b00406 ↗
71. Effect of the alkyl group on the synthesis and the electrochemical properties of N-alkyl-N-methyl-pyrrolidinium bis(trifluoromethanesulfonyl)imide ionic liquids10.1016/j.electacta.2008.09.011 ↗
72. In-situ formation of poly(ionic liquid)s with ionic liquid-based plasticizer and lithium salt in electrodes for solid-state lithium batteries10.1016/j.polymer.2019.121614 ↗
73. New horizons for inorganic solid state ion conductors10.1039/C8EE01053F ↗
74. A critical review for an accurate electrochemical stability window measurement of solid polymer and composite electrolytes10.3390/ma14143840 ↗
75. Electrochemical in situ investigations of SEI and dendrite formation on the lithium metal anode10.1039/C4CP05865H ↗
76. Dead lithium: mass transport effects on voltage, capacity, and failure of lithium metal anodes10.1039/C7TA00371D ↗
77. Dendrite-Free Li-metal battery enabled by a thin asymmetric solid electrolyte with engineered layers10.1021/jacs.7b10864 ↗
78. LiFePO4 synthesized via melt synthesis using low-cost iron precursors10.1007/s10008-015-3049-7 ↗
79. Comprehensive effort on electrode slurry preparation for better electrochemical performance of LiFePO4 battery10.1016/j.jpowsour.2020.228837 ↗
80. Exploiting materials to their full potential, a Li-ion battery electrode formulation optimization study10.1021/acsaem.0c00015 ↗
81. Effect of electrode and electrolyte thicknesses on all-solid-state battery performance analyzed with the sand equation
82. Nanostructured multi-block copolymer single-ion conductors for safer high-performance lithium batteries10.1039/C8EE02093K ↗
83. Electrochemical performance of polymer electrolytes based on Poly(vinyl alcohol)/Poly(acrylic acid) blend and Pyrrolidinium ionic liquid for lithium rechargeable batteries10.1016/j.electacta.2017.04.107 ↗
84. Temperature dependent ionic transport properties in composite solid polymer electrolytes10.1016/j.ssi.2008.01.045 ↗
85. The limited influence of transference number on the performance of nanoscale batteries10.1063/1.5142613 ↗
86. Morphology control in semicrystalline solid polymer electrolytes for lithium batteries10.1039/C9ME00028C ↗
87. Promotion of ionic conductivity of PEO-based solid electrolyte using ultrasonic vibration10.3390/polym12091889 ↗
88. Anisotropic ion transport in 2D polymer single crystal-based solid polymer electrolytes10.1016/j.giant.2020.100021 ↗
89. Confinement-entitled morphology and ion transport in ion-containing polymers10.1039/C8ME00117K ↗