Grid-shape electrical circuit assembled with resistance temperature detectors for multipoint temperature measurement of solid oxide fuel cells
Source abstract
Abstract
A multipoint temperature measurement technique using a grid-shape sensor array constructed with resistance temperature detectors (RTDs) is proposed to reduce the number of cables for measurement compared with the conventional approaches such as thermocouples. DC voltage is applied between a set of nodes in the circuit, and the voltage of the other selected nodes at the outer perimeter and the response current are measured as outputs. Theoretical expressions to correlate these outputs with the resistance of the RTDs are derived to obtain the temperature of the RTDs. The feasibility of the proposed method is examined by applying the method to temperature measurement of a flat plate under uniform, linear, and radial temperature distributions near room temperature. The accuracy estimated by comparing the results obtained by this proposed method with those obtained by conventional thermocouple measurement is confirmed within 0.51 K in the temperature range tested. Moreover, the proposed circuit was established to profile the temperature of a practical-size solid oxide fuel cell (SOFC) at its operating temperatures of 920–1000 K with and without power generation. Through the experiments conducted, the proposed technique is proven to be feasible for multipoint temperature measurement of operating SOFCs.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advancements in Solid Oxide Fuel Cells · Electronic and Structural Properties of Oxides · Gas Sensing Nanomaterials and Sensors
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (22)
Show source-provided references
1. The effect of temperature gradients on thermal cycling and isothermal ageing of micro-tubular solid oxide fuel cells10.1016/j.jpowsour.2009.01.097 ↗
2. Progress in material selection for solid oxide fuel cell technology: a review10.1016/j.pmatsci.2015.01.001 ↗
3. Experimental investigation of temperature distribution of planar solid oxide fuel cell: effects of gas flow, power generation, and direct internal reforming10.1016/j.ijhydene.2020.06.033 ↗
4. Cell integrated multi-junction thermocouple array for solid oxide fuel cell temperature sensing: N+ 1 architecture10.1016/j.jpowsour.2016.03.002 ↗
5. 3-D model calculation for planar SOFC10.1016/S0378-7753(01)00792-3 ↗
6. Numerical analysis of output characteristics of tubular SOFC with internal reformer10.1016/S0378-7753(01)00547-X ↗
7. A review of numerical modeling of solid oxide fuel cells10.1016/j.ijhydene.2006.11.028 ↗
8. Numerical simulation of intermediate-temperature direct-internal-reforming planar solid oxide fuel cell10.1016/j.energy.2010.03.058 ↗
9. Artificial neural network simulator for SOFC performance prediction10.1016/S0378-7753(02)00314-2 ↗
10. Artificial neural network model of a short stack solid oxide fuel cell based on experimental data10.1016/j.jpowsour.2013.08.018 ↗
11. In-situ studies of gas phase composition and anode surface temperature through a model DIR-SOFC steam–methane reformer at 973.15 K10.1016/j.ijhydene.2013.08.042 ↗
12. Temperature measurement and distribution inside planar SOFC stacks10.1002/fuce.201100127 ↗
13. Experimental investigation of temperature distribution over a planar solid oxide fuel cell10.1016/j.apenergy.2012.12.062 ↗
14. Measurement of transient temperature distribution behavior of a planar solid oxide fuel cell: effect of instantaneous switching of power generation and direct internal reforming10.1016/j.jpowsour.2020.229070 ↗
15. Review of temperature measurement10.1063/1.1305516 ↗
16. Fabrication and characterization of ITO thin film resistance temperature detector10.1016/j.vacuum.2016.07.028 ↗
17. A study on the fabrication of an RTD (resistance temperature detector) by using Pt thin film10.1007/BF02707199 ↗
18. Baker · 1998
19. Sugihara · 2020
20. Three-dimensional thermo-fluid electrochemical modeling of planar SOFC stacks10.1016/S0378-7753(02)00487-1 ↗
21. Quasi-three-dimensional numerical simulation of a solid oxide fuel cell short stack: effects of flow configurations including air-flow alternation10.1016/j.jpowsour.2018.08.002 ↗
22. 3D thermo-electro-chemo-mechanical coupled modeling of solid oxide fuel cell with double-sided cathodes10.1016/j.ijhydene.2019.10.139 ↗