An efficient carbon resistant composite Ni0.6Zn0.4O2-δ-GDC anode for biogas fuelled solid oxide fuel cell
Source abstract
Abstract
Abstract This paper describes the fabrication of Ni0.6Zn0.4-Gd0.2Ce0.8O2-δ (NiZn-GDC) via a two-step wet chemical synthesis technique. This composite was found to be more thermally stable and carbon resistive under the intense reducing environment of biogas. This was confirmed by different characterization techniques. The maximum power density Pmax, was achieved at 600 °C as 820 mW/cm2 and 548 mW/cm2 with hydrogen and biogas, respectively. Different characterization techniques have been performed, such as X-ray diffractometry (XRD), scanning electron microscopy (SEM/EDX), UV–visible spectroscopy, and Raman spectroscopy. The XRD pattern by Rietveld refinement showed two-phase structures of the anode composite with an average crystallite size of 25 − 35 nm before and after reduction with methane. The optical band gap ( E g o p t ) of NiZn-GDC was calculated to be 2.24eV from the Tauc plot using absorbance data. The Nyquist plot was also drawn to study the AC electrochemical impedance spectra (EIS) of the nanocomposite anode from 450 °C to 600 °C in air. The maximum DC conductivity of 1.37 S/cm was observed at a temperature of 600 °C using the four-probe DC technique.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advancements in Solid Oxide Fuel Cells · Electronic and Structural Properties of Oxides · Gas Sensing Nanomaterials and Sensors
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (91)
Show source-provided references
1. Fuel cells, an alternative to standard sources of energy10.1016/S1364-0321(01)00015-6 ↗
2. Fuel cells: the expectations for an environmental-friendly and sustainable source of energy10.1016/j.rser.2011.07.100 ↗
3. Development of anode material based on La-substituted SrTiO3 perovskites doped with manganese and/or gallium for SOFC10.1016/j.jpowsour.2008.11.132 ↗
4. Carbon tolerance, electrochemical performance and stability of solid oxide fuel cells with Ni/yttria stabilized zirconia anodes impregnated with Sn and operated with methane10.1016/j.jpowsour.2012.04.062 ↗
5. Solid oxide fuel cells (SOFCs): a review of an environmentally clean and efficient source of energy10.1016/S1364-0321(02)00014-X ↗
6. Improved oxidation of hydrocarbons with new electrodes in high temperature fuel cells10.1002/1615-6854(200112)1:3/4<205::AID-FUCE205>3.0.CO;2-5 ↗
7. Process flow model of solid oxide fuel cell system supplied with sewage biogas
8. Evaluating the performance of non-precious metal based catalysts for sulfur-tolerance during the dry reforming of biogas10.1016/j.fuel.2013.12.016 ↗
9. Activity and stability enhancement of Ni-MCM-41 catalysts by Rh incorporation for hydrogen from dry reforming of methane10.1016/j.ijhydene.2009.12.109 ↗
10. Influence of the operating parameters over dry reforming of methane to syngas10.1016/j.ijhydene.2013.05.135 ↗
11. Effect of synthesis route of mesoporous zirconia based Ni catalysts on coke minimization in conversion of biogas to synthesis gas10.1016/j.ijhydene.2015.01.023 ↗
12. The effect of impregnation strategy on methane dry reforming activity of Ce promoted Pt/ZrO210.1016/j.ijhydene.2009.09.005 ↗
13. Impact of barium and lanthanum incorporation to supported Pt and Rh on α-Al2O3 in the dry reforming of methane10.1016/j.fuel.2012.02.068 ↗
14. Dry reforming of methane using Pd-based membrane reactors fabricated from different substrates10.1016/j.memsci.2013.02.029 ↗
15. Production of synthesis gas via methane reforming with CO2 on noble metals and small amount of noble-(Rh-) promoted Ni catalysts10.1016/j.ijhydene.2005.06.010 ↗
16. Ni, Co and bimetallic Ni–Co catalysts for the dry reforming of methane10.1016/j.apcata.2009.09.026 ↗
17. Co and Ni supported on CeO2 as selective bimetallic catalyst for dry reforming of methane10.1016/j.ijhydene.2012.08.006 ↗
18. Ru incorporated Ni–MCM-41 mesoporous catalysts for dry reforming of methane: effects of Mg addition, feed composition and temperature10.1016/j.ijhydene.2011.01.120 ↗
19. Effect of cobalt (nickel) content on the catalytic performance of molybdenum carbides in dry-methane reforming10.1016/j.fuproc.2009.09.011 ↗
20. Integrating biomass gasification with solid oxide fuel cells: effect of real product gas tars, fluctuations and particulates on Ni-GDC anode10.1016/j.ijhydene.2008.03.020 ↗
21. Electrode materials and reaction mechanisms in solid oxide fuel cells: a brief review10.1007/s10008-008-0611-6 ↗
22. Recent anode advances in solid oxide fuel cells10.1016/j.jpowsour.2007.06.086 ↗
23. Alternative anode materials for solid oxide fuel cells10.1016/j.jpowsour.2007.08.011 ↗
24. Novel SOFC anodes for the direct electrochemical oxidation of hydrocarbon10.1016/S0378-7753(01)01021-7 ↗
25. Preparation and performance of a Cu–CeO2–ScSZ composite anode for SOFCs running on ethanol fuel10.1016/j.jpowsour.2006.10.056 ↗
26. Electrode materials and reaction mechanisms in solid oxide fuel cells: a brief review. III. Recent trends and selected methodological aspects10.1007/s10008-011-1341-8 ↗
27. Synthesis and electrical characterisation of the tetragonal tungsten bronze type phases, (Ba/Sr/Ca/La) 0 6MxNb1− xO3− δ (M= Mg, Ni, Mn, Cr, Fe, In, Sn): evaluation as potential anode materials for solid oxide fuel cells10.1016/S0167-2738(99)00127-7 ↗
28. A highly conductive oxide anode for solid oxide fuel cells10.1149/1.3505101 ↗
29. Synthesis and characterization of (La0.75Sr0.25)Cr0.5Mn0.5O3−δ, a redox-stable, efficient perovskite anode for SOFCs10.1149/1.1639161 ↗
30. Lanthanum chromite based catalysts for oxidation of methane directly on SOFC anodes10.1006/jcat.2001.3286 ↗
31. Double perovskites as anode materials for solid-oxide fuel cells10.1126/science.1125877 ↗
32. Electrical conduction behavior of La, Co co-doped SrTiO3 perovskite as anode material for solid oxide fuel cells10.1016/j.ijhydene.2009.05.079 ↗
33. Synthesis, crystal structure, and transport properties of La1− xCaxCr0. 5Ti0. 5O3− δ10.1016/S0167-2738(03)00103-6 ↗
34. Sulfur poisoning of Ni-based anodes for solid oxide fuel cells in H/C-based fuels10.1016/j.apcata.2014.08.015 ↗
35. Ni–M (M= Sn and Sb) intermetallic-based catalytic functional layer as a built-in safeguard for hydrocarbon-fueled solid oxide fuel cells10.1039/C5TA05498B ↗
36. Cu-Ni cermet anodes for direct oxidation of methane in solid-oxide fuel cells10.1149/1.1445170 ↗
37. Novel SOFC anodes for the direct electrochemical oxidation of hydrocarbons10.1016/S0021-9517(02)00121-5 ↗
38. Evaluation of carbon deposition behavior on the nickel/yttrium-stabilized zirconia anode-supported fuel cell fueled with simulated syngas10.1016/j.jpowsour.2010.11.095 ↗
39. Carbon tolerant Ni–Au SOFC electrodes operating under internal steam reforming conditions10.1016/j.jcat.2008.07.011 ↗
40. Fuel-cell technology: running on natural gas10.1038/23144 ↗
41. Performance of alternative oxide anodes for the electrochemical oxidation of hydrogen and methane in solid oxide fuel cells10.1002/fuce.200500216 ↗
42. A solid oxide fuel cell with a gadolinia-doped ceria anode: preparation and performance10.1016/S0167-2738(99)00111-3 ↗
43. Reactivity of ceria, Gd-and Nb-doped ceria to methane10.1016/S0926-3373(01)00299-5 ↗
44. Steam reforming of methane under water deficient conditions over gadolinium-doped ceria10.1016/j.apcatb.2008.11.003 ↗
45. Synthesis and characterization of NiO/GDC–GDC dual nano-composite powders for high-performance methane fueled solid oxide fuel cells10.1016/j.ijhydene.2012.04.140 ↗
46. Electrochemical promotion of bulk lattice-oxygen extraction for syngas generation over Ni-GDC anodes in direct-methane SOFCs10.1016/j.cej.2007.03.015 ↗
47. On the active surface state of nickel‐ceria solid oxide fuel cell anodes during methane electrooxidation10.1002/aenm.201200727 ↗
48. Ir/Ce0. 9Gd0. 1O2− x as a new potential anode component in solid oxide fuel cells integrating the concept of gradual internal reforming of methane10.1016/j.cattod.2010.03.066 ↗
49. Sn-doped Ni/YSZ anode catalysts with enhanced carbon deposition resistance for an intermediate temperature SOFC10.1016/j.apcatb.2010.03.029 ↗
50. Performance and life-time behaviour of NiCu–CGO anodes for the direct electro-oxidation of methane in IT-SOFCs10.1016/j.jpowsour.2006.10.078 ↗
51. Catalytic activity of bimetallic nickel alloys for solid-oxide fuel cell anode reactions from density-functional theory10.1016/j.jpowsour.2011.01.007 ↗
52. Propane reforming on Ni–Ru/GDC catalyst: H2 production for IT-SOFCs under SR and ATR conditions10.1016/j.apcata.2007.10.006 ↗
53. Catalytic behavior of Pd–Ni/composite anode for direct oxidation of methane in SOFCs10.1149/1.2136079 ↗
54. Bimetallic Ni-Rh catalysts with low amounts of Rh for the steam and autothermal reforming of n-butane for fuel cell applications10.1016/j.apcata.2010.03.013 ↗
55. An intermediate-temperature solid oxide fuel cell providing higher performance with hydrocarbons than with hydrogen10.1149/1.1508551 ↗
56. Open-and closed-circuit study of an intermediate temperature SOFC directly fueled with simulated biogas mixtures10.1016/j.jpowsour.2005.12.069 ↗
57. Electrochemical and thermal characterization of doped ceria electrolyte with lanthanum and zirconium10.1016/j.ceramint.2018.01.048 ↗
58. Low temperature processing of dense samarium-doped CeO2 ceramics: sintering and intermediate temperature ionic conductivity10.1007/s11581-007-0123-x ↗
59. Electrical and microstructural characterization of ceramic gadolinium-doped ceria electrolytes for ITSOFCs by sol-gel route
60. October. Catalytic performance of Ni/MgO catalyst in methane dry reforming
61. Significantly improved catalytic performance of Ni-based MgO catalyst in steam reforming of phenol by inducing mesostructure10.3390/catal5041721 ↗
62. Nitrogen‐doped carbon nanocages as efficient metal‐free electrocatalysts for oxygen reduction reaction10.1002/adma.201202424 ↗
63. BaZr 0.1 Ce 0.7 Y 0.1 Yb 0.1 O 3− δ enhanced coking-free on-cell reforming for direct-methane solid oxide fuel cells10.1039/C4TA01989J ↗
64. Synthesis, physicochemical and catalytic properties of Ni/PrCeZrO catalysts for water-gas shift reaction
65. Sulphur tolerance of Au-modified Ni/GDC during catalytic methane steam reforming10.1039/C8CY00107C ↗
66. Low temperature solid oxide fuel cells with hierarchically porous cathode nano-network10.1016/j.nanoen.2014.05.010 ↗
67. Effect of Zn doping on structural and some optical studies of nano NiO films prepared by sol-gel technique10.56431/p-3qf04c ↗
68. Characteristics of Al-doped ZnO: Ni films grown on glass by sol–gel dip coating technique10.1016/j.jscs.2015.10.004 ↗
69. Charge transfer drives anomalous phase transition in ceria10.1038/s41467-018-07526-x ↗
70. Low-frequency Raman scattering from CeO2 nanoparticles10.1007/s00339-007-4345-6 ↗
71. Raman scattering in nanosized nickel oxide NiO
72. Electrochemical performance and carbon deposition resistance of M-BaZr0.1Ce0.7Y0.1Yb0.1O3-δ (M= Pd, Cu, Ni or NiCu) anodes for solid oxide fuel cells10.1038/srep07667 ↗
73. BaZr 0.1 Ce 0.7 Y 0.1 Yb 0.1 O 3− δ enhanced coking-free on-cell reforming for direct-methane solid oxide fuel cells10.1039/C4TA01989J ↗
74. Carbon-tolerant Ni-based cermet anodes modified by proton conducting yttrium-and ytterbium-doped barium cerates for direct methane solid oxide fuel cells10.1039/C5TA06488K ↗
75. Single-component and three-component fuel cells10.1016/j.jpowsour.2011.03.078 ↗
76. High performance p-type thermoelectric oxide based on NiO10.1016/S0167-577X(00)00122-1 ↗
77. Fabrication of CuO–ZnO nanowires on a stainless steel mesh for highly efficient photocatalytic applications10.1039/c0cc04985a ↗
78. Ceramic technology: oxide-ion conductors by design10.1038/35009177 ↗
79. Review article: materials for fuel-cell technologies10.1038/35104620 ↗
80. Structure/performance relations for Ni/Yttria‐stabilized zirconia anodes for solid oxide fuel cells10.1149/1.1393220 ↗
81. Reaction of hydrogen/water mixtures on nickel‐zirconia cermet electrodes: II. AC polarization characteristics10.1149/1.1392038 ↗
82. Materials and reaction mechanisms at anode/electrolyte interfaces for SOFCs10.1016/j.ssi.2006.01.013 ↗
83. Direct conversion of biomass to electricity with solid oxide fuel cell technology10.11113/aej.v3.15384 ↗
84. Feasibility of direct-biogas SOFC10.1016/j.ijhydene.2008.07.101 ↗
85. Internal reforming SOFC running on biogas10.1016/j.ijhydene.2010.05.064 ↗
86. Cannock landfill gas powering a small tubular solid oxide fuel cell—a case study10.1016/S0378-7753(99)00417-6 ↗
87. Sofc running on biogas: identification and experimental validation of "safe" operating conditions10.1149/1.3205629 ↗
88. Experimental investigation of direct internal reforming of biogas in solid oxide fuel cells10.1016/j.ijhydene.2009.12.146 ↗
89. Fe alloying effect on the performance of the Ni anode in hydrogen fuel10.1016/j.ssi.2008.12.011 ↗
90. Electrochemical performance and carbon resistance comparison between tin, copper and silver-doped nickel/yttria-stabilized zirconia anodes SOFCs operated with biogas10.1149/2.1011906jes ↗
91. Improved performance and durability of anode supported SOFC operating on biogas10.1149/06801.2503ecst ↗