Three-dimensional agglomerate model of an anion exchange membrane fuel cell using air at the cathode – A parametric study
Source abstract
Abstract
Abstract A three-dimensional agglomerate model of an anion exchange membrane fuel cell has been developed and used to perform a parametric analysis of the effects of inlet relative humidity, ionomer water uptake, platinum loading, carbon content and ionomer volume fraction on the overall fuel cell performance. Improved cell performance has been obtained when the anode relative humidity was higher compared to the cathode resulting in a significant amount of water back diffusion, as well as higher oxygen partial pressure at the cathode enhancing the oxygen mass transport. Increasing the membrane water content positively affects the overall performance of the fuel cell because of the improvement of ionic conductivity. An increase in platinum loading has been found to have a positive impact on the fuel cell performance. Carbon loading influences the thickness of the catalyst layer, directly affecting concentration and Ohmic losses in the catalyst layer. An increase in the ionomer volume fraction enhances the transportation of ions and also the diffusion of membrane water through the membrane. A decrease in the volume fraction of ionomer in the catalyst layer leads to a reduction in the membrane water content and ion diffusion rate, thus deteriorating the overall performance of the fuel cell.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Fuel Cells and Related Materials · Electrocatalysts for Energy Conversion · Advanced battery technologies research
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (48)
Show source-provided references
1. Measurements of water uptake and transport properties in anion-exchange membranes10.1016/j.ijhydene.2010.03.026 ↗
2. Mass transport and oxygen reduction kinetics at an anion exchange membrane interface: Microelectrode studies on effect of carbonate exchange10.1149/2.007202eel ↗
3. Water uptake, ionic conductivity and swelling properties of anion-exchange membrane10.1016/j.jpowsour.2013.06.095 ↗
4. Effect of anion functional groups on the conductivity and performance of anion exchange polymer membrane fuel cells10.1016/j.jpowsour.2012.03.100 ↗
5. Study on the effect of the degree of grafting on the performance of polyethylene-based anion exchange membrane for fuel cell application10.1016/j.ijhydene.2015.10.108 ↗
6. Numerical analysis on water transport in alkaline anion exchange membrane fuel cells10.5796/electrochemistry.83.80 ↗
7. Influences of flow direction, temperature and relative humidity on the performance of a representative anion exchange membrane fuel cell: a computational analysis10.1016/j.ijhydene.2016.12.003 ↗
8. Impact of low cathode humidification on alkaline membrane fuel cell performance
9. Manipulating water in high-performance hydroxide exchange membrane fuel cells through asymmetric humidification and wetproofing10.1149/2.0131506jes ↗
10. Steady state and transient simulation of anion exchange membrane fuel cells10.1016/j.jpowsour.2017.07.012 ↗
11. Review of cell performance in anion exchange membrane fuel cells10.1016/j.jpowsour.2017.07.117 ↗
12. Beyond catalysis and membranes: visualizing and solving the challenge of electrode water accumulation and flooding in AEMFCs (vol 11, pg 551, 2018)10.1039/C8EE90013B ↗
13. Importance of balancing membrane and electrode water in anion exchange membrane fuel cells10.1016/j.jpowsour.2017.05.006 ↗
14. An improved two-dimensional agglomerate cathode model to study the influence of catalyst layer structural parameters10.1016/j.electacta.2004.12.009 ↗
15. A three-dimensional agglomerate model for the cathode catalyst layer of PEM fuel cells10.1016/j.jpowsour.2007.12.085 ↗
16. A parametric study of cathode catalyst layer structural parameters on the performance of a PEM fuel cell10.1016/j.ijhydene.2009.12.111 ↗
17. A three-dimensional agglomerate model of an anion exchange membrane fuel cell
18. Li · 2005
19. A two-phase flow and non-isothermal agglomerate model for a proton exchange membrane (PEM) fuel cell10.1016/j.energy.2014.06.065 ↗
20. A two dimensional agglomerate model for a proton exchange membrane fuel cell10.1016/j.energy.2013.08.026 ↗
21. Numerical investigation of the optimal Nafion ionomer content in cathode catalyst layer: an agglomerate two-phase flow modelling10.1016/j.ijhydene.2014.03.225 ↗
22. Analytical approach to polymer electrolyte membrane fuel cell performance and optimization10.1016/j.jelechem.2007.02.028 ↗
23. Comparative degradation study of carbon supported proton exchange membrane fuel cell electrocatalysts - the influence of the platinum to carbon ratio on the degradation rate10.1016/j.jpowsour.2014.03.039 ↗
24. Catalysis for low temperature fuel cells part I: THE cathode challenges10.1595/003214002X461314 ↗
25. Effective transport coefficients in PEM fuel cell catalyst and gas diffusion layers: beyond Bruggeman approximation10.1016/j.apenergy.2009.05.006 ↗
26. Anion exchange membranes by bromination of benzylmethyl-containing poly(sulfone)s10.1021/ma902430y ↗
27. On the modeling of water transport in polymer electrolyte membrane fuel cells10.1016/j.electacta.2009.06.070 ↗
28. Transient analysis of alkaline anion exchange membrane fuel cell anode10.1016/j.ijhydene.2013.03.045 ↗
29. Three-dimensional two-phase flow model of proton exchange membrane fuel cell with parallel gas distributors10.1016/j.jpowsour.2009.11.019 ↗
30. Mass-transport phenomena in proton-exchange membrane fuel-cells using O2/He, O2/Ar, and O2/N2 mixtures .2. Theoretical-analysis10.1149/1.2055066 ↗
31. Mass-transport phenomena in proton-exchange membrane fuel-cells using O2/He, O2/Ar, and O2/N2 mixtures .1. Experimental-analysis10.1149/1.2055065 ↗
32. A mathematical-model of the solid-polymer-electrolyte fuel-cell10.1149/1.2221251 ↗
33. Pressure-dependence of the oxygen reduction reaction at the platinum Microelectrode nafion interface - electrode-kinetics and mass-transport10.1149/1.2068992 ↗
34. Water management in alkaline anion exchange membrane fuel cell anode10.1016/j.ijhydene.2012.09.074 ↗
35. Three-dimensional multiphase modeling of alkaline anion exchange membrane fuel cell10.1016/j.ijhydene.2014.01.180 ↗
36. Measurement of water uptake in thin-film Nafion and anion alkaline exchange membranes using the quartz crystal microbalance10.1016/j.memsci.2015.09.027 ↗
37. Polymer electrolyte fuel-cell model10.1149/1.2085971 ↗
38. Heat-transfer in porous-media considering phase-change and capillarity - the heat pipe effect10.1016/0017-9310(85)90082-1 ↗
39. Analysis of liquid water transport in cathode catalyst layer of PEM fuel cells10.1016/j.ijhydene.2009.12.160 ↗
40. Analysis of free-energy and entropy changes for half-cell reactions10.1149/1.2221123 ↗
41. Coupled thermal and water management in polymer electrolyte fuel cells10.1149/1.2352039 ↗
42. Highly conductive anion exchange membrane for high power density fuel-cell performance10.1021/am503870g ↗
43. Non-platinum cathode catalysts for alkaline membrane fuel cells10.1016/j.ijhydene.2011.11.143 ↗
44. Alkaline membrane fuel cells with in-situ cross-linked ionomers10.1016/j.electacta.2014.11.055 ↗
45. Effect of carbon loading in microporous layer on PEM fuel cell performance10.1016/j.jpowsour.2006.09.020 ↗
46. Effects of platinum loading on performance of proton-exchange membrane fuel cells using surface-modified Nafion (R) membranes10.1016/j.jpowsour.2006.01.071 ↗
47. Impact of ionomer content on proton exchange membrane fuel cell performance10.1002/fuce.201500138 ↗
48. Soluble polystyrene-b-poly (ethylene/butylene)-b-polystyrene based ionomer for anion exchange membrane fuel cells operating at 70 degrees C10.1002/fuce.201700176 ↗