journal article·2022-09

Increasing the performance of all-solid-state Li batteries by infiltration of Li-ion conducting polymer into LFP-LATP composite cathode

Martin Ihrig, Enkhtsetseg Dashjav, Alexander M. Laptev, Ruijie Ye, Daniel Grüner, Mirko Ziegner, Philipp Odenwald, Martin Finsterbusch, Frank Tietz, Dina Fattakhova-Rohlfing, Olivier Guillon

Publisher page

Abstract

Polymer-ceramic composites combine the benefits of polymers and ceramics. In particular, the infiltration of the ceramic cathode with a Li-ion-conducting polymer in an all-solid-state Li-ion battery enhances the utilization of the cathode active material (CAM) and enables the application of thicker cathodes with higher storage capacity. This concept has already been validatedin our earlier work, in which a porousLiCoO2–Li6.45Al0.05La3Zr1.6Ta0.4O12 (LLZO:Al:Ta) composite cathode was fabricated by spark plasma sintering (SPS) technique. However, its performance stability was low. In the present work, the concept is modified using an LFP-LATP cathode with LiFePO4 as the CAM, Li1.5Al0.5Ti1.5(PO4)3 as the ion-conducting phase, and tapecasting with free sintering instead of SPS. Both tape-casting and free sintering are more relevant for largescale production. The sintered LFP-LATP cathode is infiltrated with the MEEP polymer and LiC2NO4F6S2 ionconducting salt. A full cell with the polymer-infiltrated cathode, LLZO:Al:Ta separator, and Li anode shows nearly full LFP utilization in the 100 μm thick cathode with an excellent area-specific storage capacity of above 3 mAh cm−2. However, after a few dozen cycles, a Li dendrite penetrates the separator leading to abrupt capacity fading. The prevention of Li dendrite formation remains a challenge for our future work.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Battery Materials and Technologies · Advancements in Battery Materials · Advanced Battery Technologies Research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (28)

Show source-provided references
1. Understanding interface stability in solid-state batteries10.1038/s41578-019-0157-5 ↗
2. Issues and challenges facing rechargeable lithium batteries10.1038/35104644 ↗
3. A solid future for battery development10.1038/nenergy.2016.141 ↗
4. Lithium battery chemistries enabled by solid-state electrolytes10.1038/natrevmats.2016.103 ↗
5. About the compatibility between high voltage spinel cathode materials and solid oxide electrolytes as a function of temperature10.1021/acsami.6b09059 ↗
6. Low-temperature sintering of fully inorganic all-solid-state batteries. – impact of interfaces on full cell performance10.1016/j.jpowsour.2020.228905 ↗
7. Compatibility study of oxide and olivine cathode materials with lithium aluminum titanium phosphate10.1007/s11581-017-2276-6 ↗
8. Microstructure, ionic conductivity, and mechanical properties of tape-cast Li1.5Al0.5Ti1.5P3O12 electrolyte sheets10.1016/j.jeurceramsoc.2020.01.017 ↗
9. Polymer–ceramic composite cathode with enhanced storage capacity manufactured by field-assisted sintering and infiltration10.1021/acsaem.1c02667 ↗
10. Study of LiCoO2/Li7La3Zr2O12:Ta interface degradation in all-solid-state lithium batteries10.1021/acsami.1c22246 ↗
11. Development and challenges of LiFePO4 cathode material for lithium-ion batteries10.1039/C0EE00029A ↗
12. The tape casting process for manufacturing low-temperature co-fired ceramic green sheets: a review10.1111/jace.15694 ↗
13. The impact of lithium tungstate on the densification and conductivity of phosphate lithium-ion conductors
14. Performance of polyphosphazene based gel polymer electrolytes in combination with lithium metal anodes10.1016/j.jpowsour.2014.09.077 ↗
15. High conductivity of mixed phase Al-substituted Li7La3Zr2O1210.1007/s10832-015-9988-7 ↗
16. Quantitative elucidation of the non-equilibrium phase transition in LiFePO4 via the intermediate phase10.1021/acs.chemmater.9b00834 ↗
17. A single-crystal X-ray, and powder neutron diffraction study on NASICON-type Li1+xAlxTi2−x(PO4)3 (0 ≤ x ≤ 0.5) crystals: implications on ionic conductivity10.1016/j.solidstatesciences.2016.08.011 ↗
18. Thermal expansion and thermally induced variations of the crystal structure of AlPO4 low cristobalite10.1127/0028-3649/2003/2003-0289 ↗
19. A mixed α/β superstructure in NASICON ionic conductors: neutron diffraction study of Li2FeTi(PO4)3 and Li2FeZr(PO4)310.1006/jssc.2000.8999 ↗
20. Conductivity, microstructure and mechanical properties of tape-cast LATP with LiF and SiO2 additives10.1007/s10853-021-06773-6 ↗
21. A new mixed valent titanium (III/IV) phosphate with a NASICON-type structure10.1016/0022-4596(91)90156-C ↗
22. The mixed-valent titanium phosphate, Li2Ti2(PO4)3, dilithium dititanium(III/IV) tris(orthophosphate)10.1107/S1600536811031606 ↗
23. All-solid-state lithium batteries based on lamellar garnet-type ceramic electrolytes10.1016/j.jpowsour.2015.09.061 ↗
24. Overcoming the interfacial limitations imposed by the solid-solid interface in solid-state batteries using ionic liquid-based interlayers
25. Water-based fabrication of a Li|Li7La3Zr2O12|LiFePO4 solid-state battery─toward green battery production10.1021/acssuschemeng.2c01349 ↗
26. Determining the limiting factor of the electrochemical stability window for PEO-based solid polymer electrolytes: main chain or terminal –OH group?10.1039/D0EE00342E ↗
27. Plating a dendrite-free lithium anode with a polymer/ceramic/polymer sandwich electrolyte10.1021/jacs.6b05341 ↗
28. NASICON Li1.2Mg0.1Zr1.9(PO4)3 solid electrolyte for an all-solid-state li-metal battery10.1002/smtd.202000764 ↗