journal article·2019-07

Mass transport in anode gas diffusion layer of direct methanol fuel cell derived from compression effect

Guangrong Deng, Liang Liang, Chenyang Li, Junjie Ge, Changpeng Liu, Zhao Jin, Wei Xing

Publisher page

Abstract

Abstract The anode gas diffusion layer plays an important role on mass transport. By adjusting the assembly pressure, the structure of gas diffusion layer can be controlled to investigate the two-phase behavior. The electrochemical test indicates that increasing the assembly pressure causes increase in mass transport resistance. Inhomogeneous compression of gas diffusion layer is observed by three-dimensional imaging technology. Based on the experimental data, a two-phase model is established. The simulated results show that the increment of surface roughness and the reduction of porosity, both derived from compression of gas diffusion layer, exacerbate CO2 blockage of the cell. Lowering polytetrafluoroethylene content of anode gas diffusion layer alleviates CO2 blockage by reducing the difference of surface tension between liquid-solid and gas-solid interface as well as the negative capillary pressure of gas diffusion layer. Thus, the peak power density climbs from 60.61 to 49.94 mW cm−2 to 74.79 and 70.47 mW cm−2 at the assembly pressure of 1.00 and 2.00 MPa, respectively. The optimal assembly pressure locates at where good contact between membrane electrode assembly and bipolar plate is achieved, with the least gas diffusion layer deformation possible.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Fuel Cells and Related Materials · Electrocatalysts for Energy Conversion · Advancements in Solid Oxide Fuel Cells

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (49)

Show source-provided references
1. Fuel cells: a new, efficient and cleaner power source10.1002/aic.690470702 ↗
2. Review and advances of direct methanol fuel cells (DMFCs) part I: design, fabrication, and testing with high concentration methanol solutions10.1016/j.jpowsour.2012.10.061 ↗
3. A review on durability issues and restoration techniques in long-term operations of direct methanol fuel cells10.1016/j.jpowsour.2015.07.094 ↗
4. Process system engineering in direct methanol fuel cell10.1016/j.ijhydene.2011.02.058 ↗
5. Heat and mass transfer characteristics of direct methanol fuel cell: experiments and model10.1016/j.egypro.2014.07.279 ↗
6. Three-dimensional Boron- and Nitrogen-codoped graphene aerogel-supported Pt nanoparticles as highly active electrocatalysts for methanol oxidation reaction10.1021/acssuschemeng.8b00425 ↗
7. A review on methanol crossover in direct methanol fuel cells: challenges and achievements10.1002/er.1889 ↗
8. Model-based design and optimization of the microscale mass transfer structure in the anode catalyst layer for direct methanol fuel cell10.1002/aic.13859 ↗
9. Green composite papers via use of natural binders and graphene for PEM fuel cell electrodes10.1021/acssuschemeng.7b02207 ↗
10. Space matters: Li+ conduction versus strain effect at FePO4/LiFePO4 interface10.1063/1.4942849 ↗
11. Interfacial strain effect on gas transport in nanostructured electrodes of solid oxide fuel cells10.1016/j.jpowsour.2015.05.030 ↗
12. Physical justification for ionic conductivity enhancement at strained coherent interfaces10.1016/j.jpowsour.2015.02.089 ↗
13. Investigation of effects of non-homogenous deformation of gas diffusion layer in a PEM fuel cell10.1002/er.3774 ↗
14. Investigation of GDL compression effects on the performance of a PEM fuel cell cathode by lattice Boltzmann method10.1016/j.jpowsour.2017.05.078 ↗
15. Investigating the effects of gas diffusion layer substrate thickness on polymer electrolyte membrane fuel cell performance via synchrotron X-ray radiography10.1016/j.electacta.2017.03.162 ↗
16. A review of the gas diffusion layer in proton exchange membrane fuel cells: durability and degradation10.1016/j.apenergy.2015.06.068 ↗
17. Stresses and their impacts on proton exchange membrane fuel cells: a review10.1016/j.ijhydene.2017.12.033 ↗
18. Measurement of effective bulk and contact resistance of gas diffusion layer under inhomogeneous compression - Part I: electrical conductivity10.1016/j.jpowsour.2016.04.110 ↗
19. Effect of assembly pressure on the performance of a bendable polymer electrolyte fuel cell based on a silver nanowire current collector10.1016/j.energy.2017.05.197 ↗
20. Investigation of contact pressure distribution over the active area of PEM fuel cell stack10.1016/j.ijhydene.2015.12.057 ↗
21. Reliability prediction of large fuel cell stack based on structure stress analysis10.1016/j.jpowsour.2017.06.041 ↗
22. Effect of compression thickness on performance of gas diffusion layer of direct methanol fuel cells10.1007/s40684-014-0027-y ↗
23. The effect of gas diffusion layer compression on gas bypass and water slug motion in parallel gas flow channels10.1002/aic.14686 ↗
24. Analysis of the clamping effects on the passive direct methanol fuel cell performance using electrochemical impedance spectroscopy10.1016/j.electacta.2016.08.080 ↗
25. Nonlinear orthotropic model of the inhomogeneous assembly compression of PEM fuel cell gas diffusion layers10.1016/j.ijhydene.2011.05.152 ↗
26. Modeling of the anode of a liquid-feed DMFC: inhomogeneous compression effects and two-phase transport phenomena10.1016/j.jpowsour.2013.06.166 ↗
27. On the effects of assembly compression on the performance of liquid-feed DMFCs under methanol-limiting conditions: a 2D numerical study10.1016/j.jpowsour.2015.02.112 ↗
28. On the effect of operating conditions in liquid-feed direct methanol fuel cells: a multiphysics modeling approach10.1016/j.energy.2016.07.074 ↗
29. Implications of inherent inhomogeneities in thin carbon fiber-based gas diffusion layers: a comparative modeling study10.1016/j.electacta.2018.09.089 ↗
30. Systemic modeling and analysis of DMFC stack for behavior prediction in system-level application10.1016/j.energy.2016.07.015 ↗
31. 2016
32. Experimental investigation of current distribution in a direct methanol fuel cell with serpentine flow-fields under various operating conditions10.1016/j.jpowsour.2009.06.052 ↗
33. Experimental investigation of current distributions in a direct methanol fuel cell with various gas diffusion layers and Nafion (R) membranes10.1016/j.jpowsour.2011.03.051 ↗
34. Capillary behavior in porous solids
35. Evaluation of capillary character in petroleum reservoir rock
36. Water flow in the gas diffusion layer of PEM fuel cells10.1016/j.memsci.2005.03.049 ↗
37. Enhancing mass transport in direct methanol fuel cell by optimizing the microstructure of anode microporous layer10.1002/aic.16193 ↗
38. Mathematical modeling of liquid-feed direct methanol fuel cells10.1149/1.1559061 ↗
39. Role of CO2 in methanol and water transport in direct methanol fuel cells, Electrochim
40. Wettability and capillary behavior of fibrous gas diffusion media for polymer electrolyte membrane fuel cells10.1016/j.jpowsour.2009.04.052 ↗
41. Flückiger · 2009
42. Characterization of direct methanol fuel cells by AC impedance spectroscopy10.1016/S0378-7753(98)00109-8 ↗
43. Impedance characteristics of the direct methanol fuel cell under various operating conditions10.1021/ef700602k ↗
44. An impedance study of an operating direct methanol fuel cell10.1016/j.jpowsour.2009.10.066 ↗
45. Impedance studies on direct methanol fuel cell anodes10.1016/S0378-7753(99)00331-6 ↗
46. Gas-diffusion-layer structural properties under compression via X-ray tomography10.1016/j.jpowsour.2016.08.020 ↗
47. Analysis of representative elementary volume and through-plane regional characteristics of carbon-fiber papers: diffusivity, permeability and electrical/thermal conductivity10.1016/j.ijheatmasstransfer.2018.07.030 ↗
48. Carbon dioxide evolution patterns in direct methanol fuel cells10.1016/S0013-4686(99)00102-4 ↗
49. In situ visualization study of CO2 gas bubble behavior in DMFC anode flow fields10.1016/j.jpowsour.2004.05.033 ↗