journal article·2023-11

When to switch from heat-up to start-up in the warming-up process of a solid oxide fuel cell: A numerical study and multi-objective planning

Masoud Hami, Javad Mahmoudimehr

Publisher page

Abstract

Solid oxide fuel cells (SOFCs) at rest need to undergo warming-up process to reach normal performance. This process begins with cell heating (so called heat-up process) and continues with the activation of electrochemical reactions (so called start-up process) until the cell performance reaches steady state. This paper develops a transient numerical model to investigate the influence of the switching temperature (ST), defined as the electrolyte average temperature at the beginning of the start-up process, on the SOFC warming-up process. Also, an optimal ST is proposed by considering the different combinations of the objectives of warming-up time duration, energy efficiency and thermal shock. The results indicate that a lower ST (or an earlier onset of start-up process) results in a shorter warming-up time duration and a greater energy efficiency (as two desirable impacts), but causes a higher thermal shock (as a negative point). Using a multi-objective decision making approach (namely, linear programming technique for multi-dimensional analysis of preference), a ST of 823 K is proposed as an optimal compromise among the three mentioned objectives. However, when the energy efficiency is disregarded, a ST of 998 K is found to be optimum.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advancements in Solid Oxide Fuel Cells · Fuel Cells and Related Materials · Electrocatalysts for Energy Conversion

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (66)

Show source-provided references
1. Comparative study on bipolar plate geometry designs on the performance of proton exchange membrane fuel cells10.1016/j.fuel.2023.128389 ↗
2. A numerical simulation to effectively assess impacts of flow channels characteristics on solid oxide fuel cell performance
3. A performance assessment study on solid oxide fuel cells for reduced operating temperatures10.1016/j.ijhydene.2014.11.115 ↗
4. An overview of fuel cell technology: fundamentals and applications10.1016/j.rser.2014.01.012 ↗
5. Three‐dimensional nonisothermal modeling of solid oxide fuel cell coupling electrochemical kinetics and species transport
6. Performance enhancement of planar solid oxide fuel cell using a novel interconnector design10.1016/j.ijhydene.2021.04.001 ↗
7. Optimal identification of solid oxide fuel cell parameters using a competitive hybrid differential evolution and Jaya algorithm10.1016/j.ijhydene.2020.11.119 ↗
8. Optimization of metal-supported solid oxide fuel cells with a focus on mass transport10.1016/j.jpowsour.2022.232402 ↗
9. Numerical study of a planar solid oxide fuel cell during heat-up and start-up operation10.1021/ie100783g ↗
10. Three-dimensional micro/macroscale simulation of planar, anode-supported, intermediate-temperature solid oxide fuel cells: I. Model development for hydrogen fueled operation10.1016/j.ijhydene.2019.04.183 ↗
11. Computational model to predict thermal dynamics of planar solid oxide fuel cell stack during start-up process10.1016/j.jpowsour.2009.11.129 ↗
12. The analyses of the start-up process of a planar, anode-supported solid oxide fuel cell using three different start-up procedures10.1016/j.jpowsour.2012.08.018 ↗
13. Thermal shock resistant solid oxide fuel cell ceramic composite electrolytes10.1016/j.jallcom.2019.153490 ↗
14. Influence of the start-up rate on the electrochemical impedance of a low temperature solid oxide fuel cell fabricated by reactive sputtering10.1016/j.tsf.2019.137445 ↗
15. Dynamic-temperature operation of metal-supported solid oxide fuel cells10.1016/j.jpowsour.2018.05.094 ↗
16. Study on preheating techniques for start-up of tubular solid oxide fuel cells10.1115/1.4004504 ↗
17. A novel flow field design with flow re-distribution for advanced thermal management in Solid oxide fuel cell10.1016/j.apenergy.2022.120364 ↗
18. Comparative analysis of thermal and redox cycling for microtubular SOFCs10.1149/1.2729257 ↗
19. A global thermo-electrochemical model for SOFC systems design and engineering10.1016/S0378-7753(03)00067-3 ↗
20. The analyses of the heat-up process of a planar, anode-supported solid oxide fuel cell using the dual-channel heating strategy10.1016/j.ijhydene.2011.02.129 ↗
21. Parameter study on solid oxide fuel cell heat-up process to reaction starting temperature10.1007/s40684-019-00129-x ↗
22. Heat up impact on thermal stresses in SOFC for mobile APU applications: thermo-structural analysis
23. Simulation-based multiobjective management of transient heating process of solid oxide fuel cell10.1002/fuce.202200113 ↗
24. Optimal heat-up planning of a solid oxide fuel cell with and without hot air recycling by considering energy, time and temperature gradient10.1002/ente.202201401 ↗
25. Steady state and transient thermal stress analysis in planar solid oxide fuel cells10.1016/j.jpowsour.2004.11.073 ↗
26. Thermal start-up behaviour and thermal management SOFCs10.1016/j.jpowsour.2005.10.052 ↗
27. Numerical analysis of start-up operation of a tubular solid oxide fuel cell10.1016/j.ijhydene.2008.11.034 ↗
28. Evaluation of extruded cathode honeycomb monolith-supported SOFC under rapid start-up operation10.1016/j.electacta.2008.09.029 ↗
29. Heat-up and start-up modeling of direct internal reforming solid oxide fuel cells10.1016/j.jpowsour.2009.12.021 ↗
30. Transient heat transfer modeling of a solid oxide fuel cell operating with humidified hydrogen10.1016/j.ijhydene.2010.11.127 ↗
31. Sanjay, Computational analysis of IR-SOFC: transient, thermal stress, carbon deposition and flow dependency10.1016/j.ijhydene.2016.04.016 ↗
32. Development of 2D dynamic model for hydrogen-fed and methane-fed solid oxide fuel cells10.1016/j.jpowsour.2016.08.005 ↗
33. On the start-up transient simulation of a turbo fuel cell system10.1016/j.jpowsour.2006.02.030 ↗
34. Fast and exergy efficient start-up of micro-solid oxide fuel cell systems by using the reformer or the post-combustor for start-up heating10.1016/j.jpowsour.2008.04.020 ↗
35. Cold start dynamics and temperature sliding observer design of an automotive SOFC APU10.1016/j.jpowsour.2008.11.043 ↗
36. Start-up characteristics of segmented-in-series tubular SOFC power modules improved by catalytic combustion at cathodes10.1002/fuce.201400014 ↗
37. Start-up and operation characteristics of a flame fuel cell unit10.1016/j.apenergy.2016.06.067 ↗
38. Techno-energy-economic sensitivity analysis of hybrid system solid oxide fuel cell/gas turbine10.3934/energy.2021044 ↗
39. On the technology of solid oxide fuel cell (SOFC) energy systems for stationary power generation: a review10.3390/su142215276 ↗
40. Analysis of start-up behavior based on the dynamic simulation of an SOFC–engine hybrid system10.1016/j.enconman.2022.116384 ↗
41. Analysing thermal regime and transient by using numerical modelling for solid oxide electrolyser aided by solar radiation10.1016/j.ijthermalsci.2022.107545 ↗
42. 4E analysis and multi-objective optimization of CCHP using MOPSOA10.1177/0954408912471001 ↗
43. Soft computing based multi-objective optimization of Brayton cycle power plant with isothermal heat addition using evolutionary algorithm and decision making10.1016/j.asoc.2016.05.001 ↗
44. Comparative thermoeconomic analyses and multi-objective particle swarm optimization of geothermal combined cooling and power systems10.1016/j.enconman.2021.113921 ↗
45. 3-D model calculation for planar SOFC10.1016/S0378-7753(01)00792-3 ↗
46. Parameter study of transient carbon deposition effect on the performance of a planar solid oxide fuel cell10.1016/j.apenergy.2014.11.061 ↗
47. A comprehensive CFD model of anode-supported solid oxide fuel cells10.1016/j.electacta.2008.11.048 ↗
48. Modeling of transport, chemical and electrochemical phenomena in a cathode-supported SOFC10.1016/j.ces.2009.03.043 ↗
49. Detailed transient thermal simulation of a planar SOFC (solid oxide fuel cell) using gPROMS™10.1016/j.energy.2014.11.049 ↗
50. A lattice Boltzmann analysis of the performance and mass transport of a solid oxide fuel cell with a partially obstructed anode flow channel10.1016/j.fuel.2022.126537 ↗
51. Reduced-order transient modeling for SOFC heating and cooling10.1016/j.jpowsour.2005.11.072 ↗
52. Three-dimensional transient modeling and transport analysis of solid oxide fuel cells under electrical load change10.1016/j.enconman.2018.03.064 ↗
53. Parametric and transient analysis of non-isothermal, planar solid oxide fuel cells10.1016/j.ijhydene.2011.09.062 ↗
54. Investigation of thermal radiation effects on solid oxide fuel cell performance by a comprehensive model10.1016/j.jpowsour.2012.01.130 ↗
55. Performance study of solid oxide fuel cell with various flow field designs: numerical study10.1016/j.ijhydene.2018.09.034 ↗
56. Performance improvement of solid oxide fuel cells by combining three-dimensional CFD modeling, artificial neural network and genetic algorithm10.1016/j.enconman.2022.116026 ↗
57. Numerical investigation of the transient performance of a reversible solid oxide cell during the mode switching process10.1016/j.enconman.2022.116048 ↗
58. 2018 · 19.2
59. Incropera · 2006
60. Patankar · 1980
61. Numerical investigation of mesoscopic volumetric ablation of 3D braided charring composites10.1016/j.applthermaleng.2020.116016 ↗
62. Moukalled · 2015
63. Feasibility study on saturated water cooled solid oxide fuel cell stack10.1016/j.apenergy.2020.115803 ↗
64. Effect of non-uniform inlet flow rate on the heat-up process of a solid oxide fuel cell unit with cross-flow configuration10.1016/j.ijhydene.2016.05.260 ↗
65. A 3D CFD model for predicting the temperature distribution in a full scale APU SOFC short stack under transient operating conditions10.1016/j.apenergy.2014.08.052 ↗
66. Numerical study on the effect of bi-polar plate geometry in the SOFC heating-up process10.1063/1.5047278 ↗