journal article·2022-04Open access

Correlating the initial gas evolution and structural changes to cycling performance of Co-free Li-rich layered oxide cathode

Hieu Quang Pham, Łukasz Kondracki, Mohamed Tarik, Sigita Trabesinger

Abstract

Alternatives to Lithium-rich layered oxides xLi2MnO3∙(1−x)LiNi1−y−zCoyMnzO2 (LR-NCMs) are needed, despite them being promising high-capacity cathode materials for next generation of high-energy batteries, because these materials contain toxic Co in their structure and their practical applications are restricted by prominent capacity and voltage fade, caused by structural transformation upon long-term cycling. To address these issues, a search for a low-cost, Co-free Li-rich cathode materials with a better surface structural stability than LR-NCMs is ongoing. One of such compounds is Li1.16Ni0.19Fe0.18Mn0.46O2 (LNFM). Our as-synthesized LNFM cathode not only delivers a high specific capacity of 229 mAh g−1 with the capacity retention of 83% in half-cell and 81% in a full-cells but also a stable average discharge voltage, even when cycled at C/5 rate to upper cutoff potential of 4.8 V vs Li+/Li in additive-free electrolyte. Both operando and post mortem characterization was used to understand the structural changes, gas evolution and oxygen redox processes of LNFM material, as well as to understand cathode−electrolyte interfacial reactions and their correlation to the improved electrochemical performance. The gained understanding will help designing new high-capacity Co-free cathode materials, meeting the performance requirements for future high-energy density batteries.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Advancements in Battery Materials · Advanced Battery Materials and Technologies · Advanced Battery Technologies Research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (70)

Show source-provided references
1. Issues and challenges facing rechargeable lithium batteries10.1038/35104644 ↗
2. Building better batteries10.1038/451652a ↗
3. Comments on the structural complexity of lithium-rich Li1+xM1-xO2 electrodes (M = Mn, Ni, Co) for lithium batteries10.1016/j.elecom.2006.06.030 ↗
4. Li2MnO3-stabilized LiMO2 (M = Mn, Ni, Co) electrodes for lithium-ion batteries10.1039/b702425h ↗
5. Alkylated LixSiyOz coating for stabilization of Li-rich layered oxide cathodes10.1016/j.ensm.2020.08.015 ↗
6. Understanding long-term cycling performance of Li1.2Ni0.15Mn0.55Co0.1O2–graphite lithium-ion cells10.1149/2.002305jes ↗
7. Understanding the interfacial phenomena of a 4.7 V and 55○C Li-ion battery with Li-rich layered oxide cathode and graphite anode and its correlation to high-energy cycling performance10.1016/j.jpowsour.2016.05.038 ↗
8. Toward 5 V lithium-ion battery: exploring the limit of charge cut-off voltage of Li-rich layered oxide cathode and high-voltage interfacial processes
9. Performance enhancement of 4.8 V Li1.2Mn0.525Ni0.175Co0.1O2 battery cathode using fluorinated linear carbonate as a high-voltage additive10.1149/2.1141412jes ↗
10. Fluorinated polyimide as a novel high-voltage binder for high-capacity cathode of lithium-ion batteries10.1002/adfm.201704690 ↗
11. Non-flammable organic liquid electrolyte for high-safety and high-energy density Li-ion batteries10.1016/j.jpowsour.2018.09.075 ↗
12. Countering the voltage decay in high capacity xLi2MnO3•(1–x)LiMO2 electrodes (M=Mn, Ni, Co) for Li+-Ion batteries10.1149/2.080206jes ↗
13. Quantifying hysteresis and voltage fade in xLi2MnO3•(1-x)LiMn0.5Ni0.5O2 electrodes as a function of Li2MnO3 content10.1149/2.049403jes ↗
14. Influence of cationic substitutions on the first charge and reversible capacities of lithium-rich layered oxide cathodes10.1039/c3ta11703k ↗
15. Effect of Fe in suppressing the discharge voltage decay of high capacity Li-rich cathodes for Li-ion batteries10.1007/s10008-015-2790-2 ↗
16. A cobalt-free Li(Li0.17Ni0.17Fe0.17Mn0.49)O2 cathode with more oxygen-involving charge compensation for lithium-ion batteries10.1002/cssc.201900241 ↗
17. Elucidating the effect of iron doping on the electrochemical performance of cobalt-free lithium-rich layered cathode materials
18. The effects of TiO2 coating on the electrochemical performance of Li[Li0.2Mn0.54Ni0.13Co0.13]O2 cathode material for lithium-ion battery10.1016/j.ssi.2008.01.091 ↗
19. Surface coating of lithium–manganese-rich layered oxides with delaminated MnO2 nanosheets as cathode materials for Li-ion batteries10.1039/c3ta15206e ↗
20. Influence of Ru substitution on Li-rich 0.55Li2MnO3·0.45LiNi1/3Co1/3Mn1/3O2 cathode for Li-ion batteries10.1016/j.electacta.2012.06.118 ↗
21. Synthesis, characterisation and electrochemical intercalation kinetics of nanostructured aluminium-doped Li[Li0.2Mn0.54Ni0.13Co0.13]O2 cathode material for lithium ion battery10.1016/j.electacta.2012.08.074 ↗
22. 3-cyano-5-fluorobenzenzboronic acid as an electrolyte additive for enhancing the cycling stability of Li1.2Mn0.54Ni0.13Co0.13O2 cathode at high voltage10.1016/j.jallcom.2020.154491 ↗
23. 1,3,5-Trihydroxybenzene as a film-forming additive for high-voltage positive electrode, Electrochem
24. Achieving high structure and voltage stability in cobalt-free Li-rich layered oxide cathodes via selective dual-cation doping10.1016/j.ensm.2020.07.035 ↗
25. Charge-compensation in 3d-transition-metal-oxide intercalation cathodes through the generation of localized electron holes on oxygen10.1038/nchem.2471 ↗
26. GSAS-II: the genesis of a modern open-source all purpose crystallography software package10.1107/S0021889813003531 ↗
27. Peng · 2016
28. Multifunctional electrolyte additive for improved interfacial stability in Ni-rich layered oxide full-cells10.1016/j.ensm.2020.08.026 ↗
29. Cross‐talk‐suppressing electrolyte additive enabling high voltage performance of Ni‐rich layered oxides in Li‐ion batteries
30. In situ X-ray diffraction characterisation of Fe0.5TiOPO4 and Cu0.5TiOPO4 as electrode material for sodium-ion batteries10.1016/j.electacta.2015.06.105 ↗
31. In-situ structural studies of manganese spinel-based cathode materials10.1016/j.electacta.2017.01.015 ↗
32. Online electrochemical mass spectrometry of high energy lithium nickel cobalt manganese oxide/graphite half- and full-cells with ethylene carbonate and fluoroethylene carbonate based electrolytes10.1149/2.0801606jes ↗
33. Differential electrochemical mass spectrometry study of the interface of x Li2MnO3·(1- x)LiMO2 (M = Ni, Co, and Mn) material as a positive electrode in li-ion batteries10.1021/cm502201z ↗
34. Operando monitoring of early Ni-mediated surface reconstruction in layered lithiated Ni-Co-Mn oxides10.1021/acs.jpcc.7b02303 ↗
35. Important aspects for reliable electrochemical impedance spectroscopy measurements of Li-ion battery electrodes10.1149/2.1061501jes ↗
36. Al doping for mitigating the capacity fading and voltage decay of layered Li and Mn-rich cathodes for Li-ion batteries10.1002/aenm.201502398 ↗
37. A comparative study on the oxidation state of lattice oxygen among Li1.14Ni0.136Co0.136Mn0.544O2, Li2MnO3, LiNi0.5Co0.2Mn0.3O2 and LiCoO2 for the initial charge-discharge10.1039/C5TA02161H ↗
38. Revealing the mitigation of intrinsic structure transformation and oxygen evolution in a layered Li1.2Ni0.2Mn0.6O2 cathode using restricted charging protocols10.1016/j.jpowsour.2017.05.089 ↗
39. Suppressing capacity fading and voltage decay of Li-rich layered cathode material by a surface nano-protective layer of CoF2 for lithium-ion batteries10.1016/j.jpowsour.2016.09.028 ↗
40. Influence of synthesis technique on the structural and electrochemical properties of “cobalt-free”, layered type Li1+x(Mn0.4Ni0.4Fe0.2)1-xO2 (0 < x < 0.4) cathode material for lithium secondary battery10.1016/j.electacta.2013.06.142 ↗
41. Raman microscopy of lithium-manganese-rich transition metal oxide cathodes10.1149/2.0361501jes ↗
42. A comparative study on electrochemical cycling stability of lithium rich layered cathode materials Li1.2Ni0.13M0.13Mn0.54O2 where M = Fe or Co10.1016/j.jpowsour.2016.05.107 ↗
43. The synthesis and electrochemical properties of xLi2MnO3-(1-x)MO2 (M = Mn1/3Ni1/3Fe1/3) via co-precipitation method, Electrochim
44. Electrochemical activation of novel Fe-based Li-rich cathode material for lithium-ion batteries10.1016/j.jallcom.2018.01.161 ↗
45. Structure and interface design enable stable Li-rich cathode10.1021/jacs.0c02302 ↗
46. Synthesis and electrochemical characterization of Fe and Ni substituted Li2MnO3 - an effective means to use Fe for constructing “co-free” Li2MnO3 based positive electrode material10.1016/j.jpowsour.2010.12.060 ↗
47. Porous lithium rich Li1.2Mn0.54Ni0.22Fe0.04O2 prepared by microemulsion route as a high capacity and high rate capability positive electrode material, Electrochim
48. Suppressing the voltage-fading of layered lithium-rich cathode materials via an aqueous binder for Li-ion batteries10.1039/C5CC10534J ↗
49. Voltage fade of layered oxides: its measurement and impact on energy density10.1149/2.034311jes ↗
50. Decoupling the voltage hysteresis of Li-rich cathodes : electrochemical monitoring
51. Electrochemical and rate performance study of high-voltage lithium-rich composition: Li1.2Mn0.525Ni0.175Co0.1O210.1016/j.jpowsour.2011.10.019 ↗
52. Electrochemical and structural characterization of carbon coated Li1.2Mn0.56Ni0.16Co0.08O2 and Li1.2Mn0.6Ni0.2O2 as cathode materials for Li-ion batteries10.1016/j.electacta.2014.06.055 ↗
53. Evidence of reversible oxygen participation in anomalously high capacity Li- and Mn-rich cathodes for Li-ion batteries10.1016/j.nanoen.2015.12.027 ↗
54. Structural transformation of a lithium-rich Li1.2Co0.1Mn0.55Ni0.15O2 cathode during high voltage cycling resolved by in situ X-ray diffraction10.1016/j.jpowsour.2012.11.144 ↗
55. In situ and ex situ XRD investigation of Li[CrxLi1/3−x/3Mn2/3−2x/3]O2 (x=1/3) cathode material10.1149/1.1584439 ↗
56. Different oxygen redox participation for bulk and surface: a possible global explanation for the cycling mechanism of Li1.20Mn0.54Co0.13Ni0.13O210.1016/j.jpowsour.2013.02.075 ↗
57. New insight into structural transformation in Li-rich manganese- based layered oxide during the initial charging10.1039/C5TA01849H ↗
58. In situ X-ray diffraction study of layered Li-Ni-Mn-Co oxides: effect of particle size and structural stability of core-shell materials10.1021/acs.chemmater.5b03500 ↗
59. Mitigating voltage decay of Li-rich cathode material via increasing Ni content for lithium-ion batteries10.1021/acsami.6b06733 ↗
60. Electrochemical activation of Li2MnO3 at elevated temperature investigated by in situ Raman microscopy10.1016/j.electacta.2013.07.130 ↗
61. Ex situ and in situ Raman microscopic investigation of the differences between stoichiometric LiMO2 and high-energy xLi2MnO3·(1-x)LiMO2 (M = Ni, Co, Mn)10.1016/j.electacta.2014.03.004 ↗
62. Structural evolution of NM (Ni and Mn) lithium-rich layered material revealed by in-situ electrochemical Raman spectroscopic study10.1016/j.jpowsour.2016.01.065 ↗
63. In situ Raman spectroscopy of layered solid solution Li2MnO3-LiMO2 (M = Ni, Mn, Co)10.1016/j.jpowsour.2012.06.083 ↗
64. Oxygen release and surface degradation of Li- and Mn-rich layered oxides in variation of the Li2MnO3 content10.1149/2.0691811jes ↗
65. Tuning electrochemical properties of Li-rich layered oxide cathodes by adjusting Co/Ni ratios and mechanism investigation using in situ X-ray diffraction and online continuous flow differential electrochemical mass spectrometry10.1021/acsami.8b00919 ↗
66. The role of oxygen release from Li- and Mn-rich layered oxides during the first cycles investigated by on-line electrochemical mass spectrometry10.1149/2.1001702jes ↗
67. Toward high-performance Li(NixCoyMnz)O2 cathodes: facile fabrication of an artificial polymeric interphase using functional polyacrylates10.1039/C8TA03954B ↗
68. Residual lithium carbonate predominantly accounts for first cycle CO2 and CO outgassing of Li-stoichiometric and Li-rich layered transition-metal oxides10.1021/jacs.7b08461 ↗
69. Tunable and robust phosphite-derived surface film to protect lithium-rich cathodes in lithium-ion batteries10.1021/acsami.5b01770 ↗
70. Effect of lithium bis(oxalato)borate additive on electrochemical performance of Li1.17Ni0.17Mn0.5Co0.17O2 cathodes for lithium-ion batteries10.1149/2.0211414jes ↗