journal article·2018-04

Measurement of the through thickness compression of a battery separator

Shutian Yan, Xiaosong Huang, Xinran Xiao

Publisher page

Abstract

Abstract The mechanical integrity of the separator is critical to the reliable operation of a battery. Due to its minimal thickness, compression experiments with a single/a few layers of separator are difficult to perform. In this work, a capacitance based displacement set-up has been developed for the measurement of the through thickness direction (TTD) compression stress-strain behavior of the separator and the investigation of its interaction with the electrode. The experiments were performed for a stack of two layers of Celgard 2400 separator, NMC cathode, and separator/NMC cathode/separator stack in both dry and wet (i.e. submersed in dimethyl carbonate DMC) conditions. The experimental results reveal that the separator compression modulus can be significantly affected by the presence of DMC. The iso-stress based rule of mixtures was used to compute the compressive stress-strain curve for the stack from that of the separator and NMC layer. The computed curve agreed with the experimental curve reasonably well up to about 0.16 strain but deviated significantly to a softer response at higher strains. The results suggest that, in the stack, the TTD compressive deformation of the separator is influenced by the NMC cathode.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Battery Technologies Research · Advancements in Battery Materials · Advanced Battery Materials and Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (35)

Show source-provided references
1. Li-ion battery separators, mechanical integrity and failure mechanisms leading to soft and hard internal shorts10.1038/srep32578 ↗
2. Coupled effect of strain rate and solvent on dynamic mechanical behaviors of separators in lithium ion batteries10.1016/j.matdes.2016.01.082 ↗
3. Coupled mechanical-electrical-thermal modeling for short-circuit prediction in a lithium-ion cell under mechanical abuse10.1016/j.jpowsour.2015.04.162 ↗
4. Three dimensional structure of celgard® microporous membranes10.1016/S0376-7388(00)81364-2 ↗
5. Mechanical behavior of a battery separator in electrolyte solutions10.1016/j.jpowsour.2011.06.026 ↗
6. Rate- and temperature-dependent material behavior of a multilayer polymer battery separator10.1007/s11665-013-0743-4 ↗
7. Deformation and fracture behaviors of microporous polymer separators for lithium ion batteries10.1039/c4ra00983e ↗
8. Characterization of microporous separators for lithium-ion batteries10.1016/S0378-7753(98)00168-2 ↗
9. Mechanical properties of a battery separator under compression and tension10.1149/2.0191411jes ↗
10. Calibration and finite element simulation of pouch lithium-ion batteries for mechanical integrity10.1016/j.jpowsour.2011.10.094 ↗
11. Deformation and failure characteristics of four types of lithium-ion battery separators10.1016/j.jpowsour.2016.07.078 ↗
12. Impact modeling of cylindrical lithium-ion battery cells: a heterogeneous approach10.1016/j.jpowsour.2016.08.034 ↗
13. Nanoindentation testing of separators for lithium-ion batteries10.1016/j.jpowsour.2013.04.036 ↗
14. Mechanical characterization and constitutive description of thin-film polymeric materials
15. Novel technique for measuring through-plane modulus in thin polymer films10.1109/96.673709 ↗
16. Study of out-of-plane elastic properties of PMDA-ODA and BPDA-PDA polyimide thin films10.1016/S0040-6090(97)01024-9 ↗
17. Dual capacitor technique for measurement of through-plane modulus of thin polymer films10.1002/(SICI)1099-0488(20000615)38:12<1634::AID-POLB90>3.0.CO;2-V ↗
18. Measuring in-thickness mechanical properties of submicron polymer dielectric films
19. Measuring the through-plane elastic modulus of thin polymer films in situ10.1016/j.microrel.2007.04.006 ↗
20. Prism coupling technique investigation of elasto-optical properties of thin polymer films10.1063/1.1812823 ↗
21. Chen · 1998
22. Picosecond ultrasonics10.1109/3.40643 ↗
23. Bailey · 2013
24. Dielectric constants for quantum chemistry and li-ion batteries: solvent blends of ethylene carbonate and ethyl methyl carbonate10.1021/acs.jpcc.5b06022 ↗
25. A multiphysics model for the in situ stress analysis of the separator in a lithium-ion battery cell10.1016/j.commatsci.2013.10.002 ↗
26. Study on design and test of flexible uniform pressure loading device10.1166/asl.2011.1641 ↗
27. Development and test analysis of flexible uniform pressure loading device
28. A multi-scale approach for the stress analysis of polymeric separators in a lithium-ion battery10.1016/j.jpowsour.2010.06.020 ↗
29. Plastic Shim Stock
30. Swelling and softening of lithium-ion battery separators in electrolyte solvents10.1016/j.jpowsour.2015.06.028 ↗
31. A model for the behavior of battery separators in compression at different strain/charge rates10.1149/2.0111411jes ↗
32. Hyer · 2009
33. Multiphysics computational framework for cylindrical lithium-ion batteries under mechanical abusive loading10.1016/j.electacta.2017.10.045 ↗
34. Integrated computation model of lithium-ion battery subject to nail penetration10.1016/j.apenergy.2016.08.101 ↗
35. Computational model of 18650 lithium-ion battery with coupled strain rate and SOC dependencies10.1016/j.apenergy.2016.03.108 ↗