3D study of the impact of aspect ratio and tilt angle on the thermoelectric generator power for waste heat recovery from a chimney
Source abstract
Abstract
Abstract In this paper, 3D study is presented for the effect of the tilt angle on the waste heat recovery from a vertical chimney by using thermoelectric generators (TEGs) cooled at their cold sides by natural convection. The aspect ratio impact (distant between two consecutive TEGs to TEG length) on the TEG performance is studied. The tilt angle changes from 0 to 15° and the aspect ratio varies from 1.5 to 4 for three vertically aligned TEGs modules mounted on the chimney wall. 3D mathematical model coupling the thermal-electric TEGs and fluid models is presented and it is programmed and solved numerically by ANSYS-Fluent software. A constructed experimental setup validates the numerical solution. The results indicate that the present mathematical model presents well the 3D results of the TEGs modules on the chimney wall. For TEGs limited number or large chimney surface area, increasing the distance between each two successive TEGs to four its length increases the TEGs output power by about 45%. Tilting the chimney wall toward the flue gases has a positive effect on the TEGs output power and tilt angle of 15° increases the uppermost TEGs power by around 5% with slight effect on the lower TEGs power.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Thermoelectric Materials and Devices · Innovative Energy Harvesting Technologies · Thermal Radiation and Cooling Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (35)
Show source-provided references
1. Jiin-Yuh Jang Y-CT. Optimization of thermoelectric generator module spacing and spreader thickness used in a waste heat recovery system. Appl. Therm. Eng. n.d.;51:677–689.10.1016/j.applthermaleng.2012.10.024 ↗
2. Lee · 2016
3. A review on heat sink for thermo-electric power generation: classifications and parameters affecting performance10.1016/j.enconman.2016.12.046 ↗
4. Constructal design of a thermoelectric device10.1016/j.ijheatmasstransfer.2005.09.028 ↗
5. A three-dimensional numerical model of thermoelectric generators in fluid power systems10.1016/j.ijheatmasstransfer.2010.08.024 ↗
6. Comparison of different modeling approaches for thermoelectric elements10.1016/j.enconman.2012.08.022 ↗
7. Muto · Differences · 2014
8. Thermoelectric generators for waste heat harvesting: a computational and experimental approach10.1016/j.enconman.2017.06.040 ↗
9. A dynamic model for thermoelectric generator applied to vehicle waste heat recovery10.1016/j.apenergy.2017.11.004 ↗
10. Study of different heat exchange technologies influence on the performance of thermoelectric generators10.1016/j.enconman.2017.11.011 ↗
11. Development of a numerical method for the performance analysis of thermoelectric generators with thermal and electric contact resistance10.1016/j.applthermaleng.2017.10.158 ↗
12. A heat transfer numerical model for thermoelectric generator with cylindrical shell and straight fins under steady-state conditions10.1016/j.applthermaleng.2014.04.018 ↗
13. A simulation framework for prediction of thermoelectric generator system performance10.1016/j.apenergy.2016.08.019 ↗
14. A numerical study on the performance of the thermoelectric module with different heat sink shapes10.1016/j.applthermaleng.2017.09.097 ↗
15. Modeling and analysis of the effect of thermal losses on thermoelectric generator performance using effective properties10.1016/j.apenergy.2017.11.096 ↗
16. Experimental investigation of the applicability of a thermoelectric generator to recover waste heat from a combustion chamber10.1016/j.apenergy.2015.04.077 ↗
17. Optimization of a waste heat recovery system with thermoelectric generators by three-dimensional thermal resistance analysis10.1016/j.enconman.2016.08.038 ↗
18. Experimental investigation on thermoelectric generator with non-uniform hot-side heat exchanger for waste heat recovery10.1016/j.enconman.2017.08.030 ↗
19. Performance investigation and design optimization of a thermoelectric generator applied in automobile exhaust waste heat recovery10.1016/j.enconman.2016.04.080 ↗
20. Dynamic performance analysis of a cascaded thermoelectric generator10.1016/j.apenergy.2017.06.108 ↗
21. Experimental and numerical study of waste heat recovery characteristics of direct contact thermoelectric generator10.1016/j.enconman.2017.03.014 ↗
22. Thermal analysis of a thermoelectric generator for light-duty diesel engines10.1016/j.apenergy.2018.05.114 ↗
23. Cylindrical thermoelectric generator with water heating system for high solar energy conversion efficiency10.1016/j.apenergy.2018.06.015 ↗
24. Versteeg · 2007
25. Effect of viscous dissipation in natural convection along a heated vertical plate10.1016/j.apm.2004.10.007 ↗
26. Thermodynamic properties of air and mixtures of nitrogen, argon, and oxygen from 60 to 2000 K at pressures to 2000 Mpa10.1063/1.1285884 ↗
27. Correlations for Nusselt number in free convection from an isothermal inclined square plate by a numerical simulation
28. Export Grade SP1848 27145 40*40mm (n.d).
29. Theoretical modeling of thermoelectric generator with particular emphasis on the effect of side surface heat transfer10.1016/j.energy.2015.12.005 ↗
30. Yaws · 1999
31. Smith · 2002
32. Indium Corp. Indalloy® 281 Bi-sn Solder Alloy (n.d).
33. Taylor · 1997
34. Thermoelectric characteristics of n-type Bi2Te3 and p-type Sb2Te3 thin films prepared by Co-evaporation and annealing for thermopile sensor applications10.2320/matertrans.M2013010 ↗
35. Bergman · 2011