Fluorinated polybenzimidazole as binders for high-temperature proton exchange membrane fuel cells
Source abstract
Abstract
The performance of high-temperature proton exchange membrane fuel cells (HT-PEMFCs) is highly affected by the binders in the catalyst layer. However, the currently commonly used binders such as acidophilic polybenzimidazoles (PBIs) and hydrophobic fluorinated polymers (e.g. PTFE) could not conduct protons or facilitate rapid gas transport simultaneously. Herein, two fluorinated PBIs (F6PBI and F4PBI) are designed and synthesized as binder materials from the easily obtained monomers of hexafluoroglutaric acid (HFGA) and tetrafluoroterephthalic acid (TFPA). Combined with the good proton conductivity of PBI and high fuel permeability of PTFE, the H 2/O 2 single cell based on PA /mPBI membrane using F6PBI binder in catalyst layer exhibits a larger electrochemical surface area (ECSA) of 67 cm 2/mg Pt corresponding to a Pt-mass specific power density of 1.41 W/mg Pt . Therefore, the MEA achieved the highest peak power density of 705 mW/cm 2 at 160 °C with F6PBI binder of 5 wt% and catalyst of 0.50 mg Pt/cm 2, which is over 100 mW/cm 2 higher than MEAs using mPBI and PTFE as binder materials. And the H 2/O 2 cell using F6PBI binder exhibits good stability of more than 800 h at a current of 0.3 A/cm 2 at 160 °C.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Fuel Cells and Related Materials · Electrocatalysts for Energy Conversion · Advancements in Solid Oxide Fuel Cells
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (44)
Show source-provided references
1. A review of high-temperature proton exchange membrane fuel cell (HT-PEMFC) system10.1016/j.ijhydene.2016.06.211 ↗
2. acid-doped polybenzimidazoles: a new polymer electrolyte10.1149/1.2044337 ↗
3. Analyzing the influence of H3PO4 as catalyst poison in high temperature PEM fuel cells using in-operando X-ray absorption spectroscopy10.1021/jp311924q ↗
4. Anion resistant oxygen reduction electrocatalyst in phosphoric acid fuel cell10.1021/acscatal.8b00390 ↗
5. Mitigating phosphate anion poisoning of cathodic Pt/C catalysts in phosphoric acid fuel cells10.1021/jp309282n ↗
6. Enhanced performance of polybenzimidazole-based high temperature proton exchange membrane fuel cell with gas diffusion electrodes prepared by automatic catalyst spraying under irradiation technique10.1016/j.jpowsour.2013.05.128 ↗
7. Effect of platinum distribution in dual catalyst layer structured gas diffusion electrode on the performance of high temperature PEMFC10.1149/2.077404jes ↗
8. Role of binders in high temperature PEMFC electrode10.1149/1.3573773 ↗
9. Gas diffusion electrodes for high temperature PEM-type fuel cells: role of a polymer binder and method of the catalyst layer deposition10.1007/s10800-011-0325-9 ↗
10. Influence of catalyst layer binder on catalyst utilization and performance of fuel cell with polybenzimidazole-H3PO4 membrane10.1149/1.3098499 ↗
11. Study of the catalytic layer in polybenzimidazole-based high temperature PEMFC: effect of platinum content on the carbon support10.1002/fuce.200900088 ↗
12. The effect of electrode parameters on performance of a phosphoric acid-doped PBI membrane fuel cell10.1016/j.ijhydene.2009.11.027 ↗
13. Study of the influence of the amount of PBI-H3PO4 in the catalytic layer of a high temperature PEMFC10.1016/j.ijhydene.2009.11.091 ↗
14. Dependence of the performance of a high-temperature polymer electrolyte fuel cell on phosphoric acid-doped polybenzimidazole ionomer content in cathode catalyst layer10.1016/j.jpowsour.2007.03.082 ↗
15. Fuel cell performance using a phosphonated polysulphone ionomer (PSUgPVPA) in the PEM cathode electrode10.1149/04523.0033ecst ↗
16. A novel dual catalyst layer structured gas diffusion electrode for enhanced performance of high temperature proton exchange membrane fuel cell10.1016/j.jpowsour.2013.07.062 ↗
17. Oxygen reduction on carbon supported platinum catalysts in high temperature polymer electrolytes10.1016/S0013-4686(00)00554-5 ↗
18. Poly(vinylimidazole) radiografted PVDF nanospheres as alternative binder for high temperature PEMFC electrodes10.1016/j.jpowsour.2015.06.105 ↗
19. The stability of Pt/C catalyst in H3PO4/PBI PEMFC during high temperature life test10.1016/j.jpowsour.2006.09.069 ↗
20. Effect of vinylphosphonic acid and polymer binders with phosphate groups on performance of high-temperature polymer electrolyte membrane fuel cell10.1016/j.cattod.2019.07.046 ↗
21. Synergistically integrated phosphonated poly(pentafluorostyrene) for fuel cells10.1038/s41563-020-00841-z ↗
22. Unusual influence of binder composition and phosphoric acid leaching on oxygen mass transport in catalyst layers of high-temperature proton exchange membrane fuel cells10.1016/j.jpowsour.2020.228616 ↗
23. Influence of the polytetrafluoroethylene content on the performance of high-temperature polymer electrolyte membrane fuel cell electrodes10.1016/j.ijhydene.2016.02.156 ↗
24. Performance of phosphonated hydrocarbon ionomer in the fuel cell cathode catalyst layer10.1149/2.046303jes ↗
25. An operationally flexible fuel cell based on quaternary ammonium-biphosphate ion pairs10.1038/nenergy.2016.120 ↗
26. Phosphoric acid-doped electrodes for a PBI polymer membrane fuel cell10.1002/er.1708 ↗
27. Preparation and operation of gas diffusion electrodes for high-temperature proton exchange membrane fuel cells10.1016/j.jpowsour.2007.07.019 ↗
28. Influence of the phosphoric acid-doping level in a polybenzimidazole membrane on the cell performance of high-temperature proton exchange membrane fuel cells10.1016/j.jpowsour.2008.12.115 ↗
29. Long-term cell degradation mechanism in high-temperature proton exchange membrane fuel cells10.1016/j.jpowsour.2012.02.098 ↗
30. Durability of ABPBI-based MEAs for high temperature PEMFCs at different operating conditions10.1002/fuce.200700059 ↗
31. Membrane electrode assemblies for high-temperature polymer electrolyte fuel cells based on poly(2,5-benzimidazole) membranes with phosphoric acid impregnation via the catalyst layers10.1016/j.jpowsour.2009.03.051 ↗
32. Studies of performance degradation of a high temperature PEMFC based on H3PO4-doped PBI10.1016/j.jpowsour.2006.07.008 ↗
33. Influence of operating temperature on cell performance and endurance of high temperature proton exchange membrane fuel cells10.1016/j.jpowsour.2009.08.097 ↗
34. Characterization of gas crossover and its implications in PEM fuel cells10.1002/aic.10780 ↗
35. Thermally treated polyaniline/polybenzimidazole blend membranes: structural changes and gas transport properties10.1016/j.memsci.2017.04.062 ↗
36. Influence of catalyst layer polybenzimidazole molecular weight on the polybenzimidazole-based proton exchange membrane fuel cell performance10.1016/j.ijhydene.2013.08.011 ↗
37. Synthesis and characterization of fluorine-containing polybenzimidazole for proton conducting membranes in fuel cells10.1002/pola.23979 ↗
38. Symmetric sponge-like porous polybenzimidazole membrane for high temperature proton exchange membrane fuel cells10.1016/j.memsci.2020.118981 ↗
39. Tailoring the microporosity of polymers of intrinsic microporosity for advanced gas separation by atomic layer deposition10.1002/anie.202016901 ↗
40. Synthesis and characterization of high molecular weight hexafluoroisopropylidene-containing polybenzimidazole for high-temperature polymer electrolyte membrane fuel cells10.1002/pola.23467 ↗
41. Arylether-type polybenzimidazoles bearing benzimidazolyl pendants for high-temperature proton exchange membrane fuel cells10.1016/j.jpowsour.2018.05.011 ↗
42. Polybenzimidazoles, new thermally stable polymers - comments10.1002/pola.1996.825 ↗
43. Improving the performance of high-temperature PEM fuel cells based on PBI electrolyte10.1016/j.jpowsour.2006.01.047 ↗
44. Ionomer content effect on charge and gas transport in the cathode catalyst layer of proton-exchange membrane fuel cells10.1016/j.jpowsour.2021.229531 ↗