Study of the acetonitrile poisoning of platinum cathodes on proton exchange membrane fuel cell spatial performance using a segmented cell system
Source abstract
Abstract
Abstract Due to the wide applications of acetonitrile as a solvent in the chemical industry, acetonitrile can be present in the air and should be considered a possible pollutant. In this work, the spatial proton exchange membrane fuel cell performance exposed to air with 20 ppm CH 3 CN was studied using a segmented cell system. The injection of CH 3 CN led to performance losses of 380 mV at 0.2 A cm −2 and 290 mV at 1.0 A cm −2 accompanied by a significant change in the current density distribution. The observed local currents behavior is likely attributed to acetonitrile chemisorption and the subsequent two consecutive reduction/oxidation reactions. The hydrolysis of CH 3 CN and its intermediate imine species resulted in NH 4 + formation, which increased the high-frequency resistance of the cell and affected oxygen reduction and performance. Other products of hydrolysis can be oxidized to CO 2 under the operating conditions. The reintroduction of pure air completely recovered cell performance within 4 h at 1.0 A cm −2 , while at 0.2 A cm −2 the cell recovery was only partial. A detailed analysis of the current density distribution, its correlation with spatial electrochemical impedance spectroscopy data, possible CH 3 CN oxidation/reduction mechanisms and mitigation strategies are presented and discussed.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Electrocatalysts for Energy Conversion · Fuel Cells and Related Materials · Electrochemical Analysis and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (100+)
Show source-provided references
1. The effects of battlefield contaminants on PEMFC performance10.1016/S0378-7753(99)00341-9 ↗
2. Mepsted · 2001
3. A review of PEM hydrogen fuel cell contamination: impacts, mechanisms, and mitigation10.1016/j.jpowsour.2006.12.012 ↗
4. Effect of contaminants on polymer electrolyte membrane fuel cells10.1016/j.pecs.2010.06.003 ↗
5. The impact of air contaminants on PEMFC performance10.1016/j.jpowsour.2007.12.091 ↗
6. Effects of atmospheric trace species on the oxygen reduction reaction on the production of H2O210.1149/1.2981931 ↗
7. Effect of air contaminants on electrolyte degradation in PEMFC10.1149/1.3210634 ↗
8. The effect of ambient contamination on PEMFC performance10.1016/j.jpowsour.2006.12.103 ↗
9. Assessing durability of cathodes exposed to common air impurities10.1016/j.jpowsour.2004.06.036 ↗
10. Effects of contaminants of catalyst activity
11. The effect of mine conditions on the performance of a PEM fuel cell10.1016/j.jpowsour.2004.02.026 ↗
12. Impact of SO2 on the oxygen reduction reaction at Pt/Vulcan carbon electrocatalysts10.1149/1.2736648 ↗
13. Deactivation of Pt/VC PEMFC cathodes by SO2, H2S and COS10.1016/j.jpowsour.2008.11.072 ↗
14. Influence of SO2 concentration and relative humidity on electrode poisoning in PEMFC10.1299/jtst.7.619 ↗
15. Sulphur dioxide poisoning and recovery of Pt nanoparticles: effect of particle size10.1016/S1452-3981(23)16521-7 ↗
16. PEMFC contamination model: competitive adsorption demonstrated with NO210.1149/1.2833301 ↗
17. Effect, mechanism and recovery of NOx poisoning on oxygen reduction reaction at Pt/C catalysts10.1016/j.jpowsour.2010.07.091 ↗
18. Oxygen reduction reaction on Pt/carbon fuel cell catalyst in the presence of trace quantities of ammonium ions: an RRDE study10.1016/j.ijhydene.2011.12.040 ↗
19. Ionic transport and water vapor uptake of ammonium exchange perfluorosulfonic acid membranes10.1149/2.040203jes ↗
20. Diagnosis of contamination introduced by ammonia at the cathode in a PEMFC10.1016/j.ijhydene.2012.05.125 ↗
21. The effect of nitrogen oxides in air on the performance of PEMFC10.1016/j.electacta.2005.11.018 ↗
22. Effects of atmospheric aerosol on the performance of environmentally sustainable passive air-breathing PEM fuel cells10.1016/j.ijhydene.2012.08.132 ↗
23. Effect of ammonium ion distribution on Nafion conductivity10.1016/j.jpowsour.2010.07.080 ↗
24. Imamura · 2009
25. The effect of NaCl in the cathode air stream on PEMFC performance10.1002/fuce.200600206 ↗
26. PEMFC contamination: testing and diagnosis of toluene-induced cathode degradation10.1016/j.jpowsour.2008.07.006 ↗
27. Quantitative ranking criteria for PEMFC contaminants10.1016/j.ijhydene.2012.01.029 ↗
28. The impact of operating conditions on the performance effect of selected airborne PEMFC contaminants10.1149/05002.0635ecst ↗
29. Cell performance in a PEMFC stack during contamination10.1149/05801.0555ecst ↗
30. Anodic displacement of chemisorbed hydrogen in electrosorption of organic molecules at platinum: a new effect for characterizing chemisorption at electrodes10.1016/S0022-0728(71)80158-4 ↗
31. Electrochemisorption and reactivity of nitriles at Pt electrodes and the anodic H desorption effect10.1016/S0022-0728(72)80153-0 ↗
32. Anodic displacement of adsorbed H in electrochemisorption of organic molecules at Pt10.1039/f19726801566 ↗
33. Electrochemical behavior of acidic acetonitrile solutions at Pt and Au electrodes10.1016/S0022-0728(77)80529-9 ↗
34. Formation of ethane during the electroreduction of acetonitrile at a platinized platinum electrode. A special feature in diluted aqueous solutions10.1016/S0022-0728(80)80032-5 ↗
35. Surface structure dependence of reactive chemisorption of acetonitrile on single-crystal Pt surfaces10.1016/0022-0728(94)03539-3 ↗
36. The behavior of high polar organic solvent at Pt electrode. II. Adsorption and electrode reactions of acetonitrile10.1016/0013-4686(80)80011-9 ↗
37. Electrochemical hydrogenation of nitriles to primary amines at transition metals: A review
38. Electrocatalytic hydrogenation of nitriles to primary amines
39. Electro-oxidation and electroreduction of acetonitrile in aqueous acid solution10.1016/0022-0728(93)80487-3 ↗
40. A SNIFTIRS study of the diffuse double layer at single crystal Pt electrodes in acetonitrile10.1016/0013-4686(95)00352-5 ↗
41. The reactive chemisorption of acetonitrile on Pt (111) and Pt (100) electrodes as examined by in situ infrared spectroscopy10.1016/S0022-0728(96)04839-5 ↗
42. Electrooxidation and electroreduction of undiluted acetonitrile at Pt microelectrodes. In situ determination of water in acetonitrile10.1002/1521-4109(200105)13:8/9<621::AID-ELAN621>3.0.CO;2-2 ↗
43. Adsorption behavior of acetonitrile on Pt and Au electrodes of various structures in solution of 0.5 M H2SO410.1016/j.electacta.2009.01.047 ↗
44. Molecular oxygen reduction at Pt and Au electrodes in acetonitrile solutions10.1149/1.2119951 ↗
45. Oxygen reduction on polycrystalline Pt and Au electrodes in perchloric acid solution in the presence of acetonitrile10.1016/S1452-3981(23)18256-3 ↗
46. Inhibiting effect of acetonitrile on oxygen reduction on polycrystalline Pt electrode in sodium chloride solution10.2298/HEMIND111010097S ↗
47. Impact of acetonitrile poisoning on oxygen reduction reaction at Pt/C catalysts10.1016/j.jpowsour.2012.11.100 ↗
48. Segmented polymer electrolyte membrane fuel cells – A review10.1016/j.rser.2010.08.024 ↗
49. A printed circuit board approach to measuring current distribution in a fuel cell10.1023/A:1003206513954 ↗
50. In-situ methods for the determination of current distributions in PEM fuel cells10.1016/S0013-4686(98)00137-6 ↗
51. Oscillations in gas channels. Part I. The forgotten player in impedance spectroscopy in PEFCs10.1149/1.2435706 ↗
52. Oscillations in gas channels. Part II. Unraveling the characteristics of the low frequency loop in air-fed PEFC impedance spectra10.1149/1.2742291 ↗
53. PEMFC operation failure under severe dehydration10.1016/j.ijhydene.2011.11.059 ↗
54. Systematic study of back pressure and anode stoichiometry effects on spatial PEMFC performance distribution10.1016/j.electacta.2011.07.058 ↗
55. Systematic studies of the gas humidification effects on spatial PEMFC performance distributions10.1016/j.electacta.2012.02.111 ↗
56. Application of a segmented cell setup to detect pinhole and catalyst loading defects in proton exchange membrane fuel cells10.1016/j.electacta.2012.04.138 ↗
57. Effects of local variations of the gas diffusion layer properties on PEMFC performance using a segmented cell system10.1016/j.electacta.2012.07.031 ↗
58. Use of segmented cell operated in H2 recirculation mode to detect water accumulation in PEMFC10.1002/fuce.201200109 ↗
59. Current distribution of a PEMFC under CO poisoning10.1149/1.3210641 ↗
60. Measurement and modeling of carbon monoxide poisoning distribution within a polymer electrolyte fuel cell10.1016/j.ijhydene.2007.01.019 ↗
61. The influence of CO2, CO and air bleed on the current distribution of a polymer electrolyte fuel cell10.1016/j.ijhydene.2008.02.002 ↗
62. The influence of CO on the current density distribution of high temperature polymer electrolyte membrane fuel cells10.1016/j.electacta.2011.08.039 ↗
63. The electro-oxidation of H2, CO in a model PEN fuel cell: oscillations, chaos, pulses10.1149/2.002306jes ↗
64. Spatial PEMFC performance under CO poisoning at a low concentration using a segmented cell system10.1016/j.jpowsour.2012.07.015 ↗
65. Study of low concentration CO poisoning of Pt anode in a proton exchange membrane fuel cell using spatial electrochemical impedance spectroscopy10.1016/j.jpowsour.2014.06.146 ↗
66. A new technique for two-dimensional current distribution measurements in electrochemical cells10.1023/A:1004047412066 ↗
67. Further refinements in the segmented cell approach o diagnosing performance in polymer electrolyte fuel cells10.1016/S0378-7753(03)00533-0 ↗
68. Study of acetylene poisoning of Pt cathode on proton exchange membrane fuel cell spatial performance using a segmented cell system10.1016/j.jpowsour.2015.04.073 ↗
69. Characterization of polymer electrolyte fuel cells using AC impedance spectroscopy10.1149/1.1836485 ↗
70. Electrochemical impedance study of electrode-membrane assemblies in PEM fuel cells. I. Electro-oxidation of H2 and H2/CO mixtures on Pt-based gas-diffusion electrodes10.1149/1.1392588 ↗
71. Change of EIS during CO poisoning of the Pt and PtRu anodes in a membrane fuel cell (PEFC)10.1016/S0013-4686(03)00528-0 ↗
72. CO tolerance of commercial Pt and PtRu gas diffusion electrodes in polymer electrolyte fuel cells10.1002/fuce.200400021 ↗
73. Impedance studies on direct methanol fuel cell anodes10.1016/S0378-7753(99)00331-6 ↗
74. Impedance studies on mesocarbon microbeds supported Pt-Ru catalytic anode10.1016/S0378-7753(02)00527-X ↗
75. Electrochemical impedance spectroscopy study of methanol oxidation on nanoparticulate PtRu direct methanol fuel cell anodes: kinetics and performance evaluation10.1016/j.jpowsour.2006.08.010 ↗
76. Impedance plane display of a reaction with an adsorbed intermediate10.1016/S0022-0728(72)80477-7 ↗
77. AC impedance of faradaic reactions involving electrosorbed intermediates – I. Kinetic theory10.1016/0013-4686(87)80005-1 ↗
78. On the impedance plane displays for irreversible electrode reactions based on the stability conditions of the steady-state. I. One state variable besides electrode potential10.1016/0013-4686(90)90077-D ↗
79. Calculation, simulation and interpretation of electrochemical impedances. Part 3. Conditions for observation of low frequency inductive diagrams for a two-step electron transfer reaction with an adsorbed intermediate species10.1016/0022-0728(92)80500-4 ↗
80. On the intrinsic electrochemical nature of the inductance in EIS. A Monte Carlo simulation of the two-consecutive-step mechanism: the flat surface 2 D case10.1016/j.electacta.2008.07.023 ↗
81. Reaction mechanisms of O2 reduction/evolution reactions
82. Oxygen electrochemistry
83. Nafion perfluorinated membranes treated in Fenton media: radical species detected by ESR spectroscopy10.1021/jp037519c ↗
84. Degradation mechanism study of perfluorinated proton exchange membrane under fuel cell operating conditions10.1016/j.electacta.2007.11.010 ↗
85. Comparison of two accelerated Nafion™ degradation experiments10.1016/j.polymdegradstab.2007.10.001 ↗
86. Radical (HO•, H• and HOO•) formation and ionomer degradation in polymer electrolyte fuel cells10.1149/1.3581040 ↗
87. PEMFC cathode contamination evaluation with conductivity call
88. Mechanism of the dissociation and electroreduction of ethanol and acetaldehyde on Pt as studied by SERS10.1021/jp807350h ↗
89. Ethanol, acetaldehyde and acetic acid adsorption/electroreduction on a Pt thin film electrode under continuous electrolyte flow: an in situ ATP-FTIRS flow cell study10.1021/jp101441q ↗
90. Electrocatalysis of direct alcohol fuel cells: A quantitative DEMS studies
91. Catalytic wet oxidation of acetic acid using platinum on alumina monolith catalyst10.1016/S0920-5861(97)00122-3 ↗
92. Catalytic wet air oxidation of low molecular weight carboxylic acids using a carbon supported platinum catalyst10.1016/S0926-3373(00)00162-4 ↗
93. Ruthenium and platinum catalysts supported on Ce, Zr, Pr-O mixed oxides prepared by soft chemistry for acetic acid wet air oxidation10.1016/j.apcatb.2006.10.002 ↗
94. Oxygen reduction on Pt in aqueous sulphuric acid in the presence of ammonium10.1016/j.electacta.2005.08.011 ↗
95. A comparative study of ORR at the Pt electrode in ammonium ion-contaminated H2SO4 and HClO4 solutions10.1016/j.jpowsour.2012.07.103 ↗
96. The effect of ammonium ions on oxygen reduction and hydrogen peroxide formation on polycrystalline Pt electrodes10.1016/j.jpowsour.2007.08.067 ↗
97. S. Knights, N. Jia, C. Chuy, J. Zhang, Fuel cell reactant supply – effects of reactant contaminants, Fuel cell seminar 2005, November 14-18, 2005, Palm Spring, CA, USA, Extended abstracts, p. 121.
98. Effect of air contaminants on electrolyte degradation in PEMFCs10.1149/1.3210634 ↗
99. Effect of ammonia as potential fuel impurity on PEMFC10.1149/1.1447221 ↗
100. Effect of transient ammonia concentrations on PEMFC performance10.1149/1.1574651 ↗