journal article·2021-11

Mitigation of mechanical membrane degradation in fuel cells – Part 2: Bonded membrane electrode assembly

D. Ramani, N.S. Khattra, Y. Singh, F.P. Orfino, M. Dutta, E. Kjeang

Publisher page

Abstract

Abstract Repetitive hygrothermal fluctuations cause mechanical membrane degradation in fuel cells, which requires mitigation for longevity. Part 1 of this work demonstrated that gas diffusion layers (GDLs) with low surface roughness can improve lifetime by reducing harmful buckling phenomena during wet/dry cycling. As a second novel mitigation approach in the present work (Part 2), the catalyst coated membrane (CCM) is bonded with the GDLs to eliminate relative motion and further curb mechanical degradation. A custom miniaturized fuel cell fixture is used within a laboratory-based X-ray computed tomography system to visualize the membrane degradation process during wet/dry cycling. Compared to a non-bonded baseline cell, membrane buckling is shown to be completely arrested with bonding and lead to a two-fold increase in lifetime. Membrane crack development is still observed as the key failure mode, preceded by cathode catalyst layer fracture. However, the root causes are related to bonding irregularities and compressive impingement of GDL fibers rather than membrane buckling. Complementary finite element simulations of a representative fuel cell assembly are carried out to fundamentally establish the favorable effect of improved CCM-GDL adhesion on membrane durability. Overall, the improved adhesion of the bonded cell provided substantial mitigation against fatigue-driven mechanical membrane degradation and failure.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Fuel Cells and Related Materials · Advanced Battery Technologies Research · Electrocatalysts for Energy Conversion

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (43)

Show source-provided references
1. Accelerated membrane durability testing of heavy duty fuel cells10.1149/2.0671501jes ↗
2. Membrane accelerated stress test development for polymer electrolyte fuel cell durability validated using field and drive cycle testing10.1149/2.0101806jes ↗
3. Microstructural and mechanical characterization of catalyst coated membranes subjected to in situ hygrothermal fatigue10.1149/2.0471514jes ↗
4. New insights into perfluorinated sulfonic-acid ionomers10.1021/acs.chemrev.6b00159 ↗
5. Deterioration of mechanical properties: a cause for fuel cell membrane failure10.1016/j.memsci.2010.02.060 ↗
6. Creep properties of catalyst coated membranes for polymer electrolyte fuel cells10.1016/j.jpowsour.2015.03.082 ↗
7. Mitigation of mechanical membrane degradation in fuel cells by controlling electrode morphology — a 4D in-situ structural characterization
8. Mitigation of mechanical membrane degradation in fuel cells – Part 1: gas diffusion layers with low surface roughness
9. Tracking the evolution of mechanical degradation in fuel cell membranes using 4D in situ visualization10.1016/j.jpowsour.2018.11.049 ↗
10. 4D in situ visualization of mechanical degradation evolution in reinforced fuel cell membranes10.1016/j.ijhydene.2020.02.013 ↗
11. Failure analysis of fuel cell electrodes using three-dimensional multi-length scale X-ray computed tomograp1
12. Morphological analyses of polymer electrolyte fuel cell electrodes with nano-scale computed tomography imaging10.1002/fuce.201300008 ↗
13. Three-dimensional phase segregation of micro-porous layers for fuel cells by nano-scale X-ray computed tomography10.1016/j.jpowsour.2016.02.001 ↗
14. X-ray tomographic analysis of porosity distributions in gas diffusion layers of proton exchange membrane fuel cells10.1016/j.electacta.2014.11.143 ↗
15. X-ray computed tomography reconstruction and analysis of polymer electrolyte membrane fuel cell porous transport layers10.1016/j.ijhydene.2012.08.077 ↗
16. 3D failure analysis of pure mechanical and pure chemical degradation in fuel cell membranes10.1149/2.0451713jes ↗
17. Characterization of membrane degradation growth in fuel cells using X-ray computed tomography10.1149/2.0251806jes ↗
18. 3D visualization of membrane failures in fuel cells10.1016/j.jpowsour.2017.01.129 ↗
19. 3D printed flow field and fixture for visualization of water distribution in fuel cells by X-ray computed tomography10.1149/2.0461613jes ↗
20. Four-dimensional joint visualization of electrode degradation and liquid water distribution inside operating polymer electrolyte fuel cells
21. 4D in situ visualization of electrode morphology changes during accelerated degradation in fuel cells by X-ray computed tomography10.1016/j.jpowsour.2017.03.058 ↗
22. High performance catalyzed membranes of ultra‐low Pt loadings for polymer electrolyte fuel cells10.1149/1.2069277 ↗
23. Microscale X-ray tomographic investigation of the interfacial morphology between the catalyst and micro porous layers in proton exchange membrane fuel cells10.1016/j.jpowsour.2016.04.031 ↗
24. Morphological features (defects) in fuel cell membrane electrode assemblies10.1016/j.jpowsour.2005.12.027 ↗
25. Water sorption and expansion of an ionomer membrane constrained by fuel cell electrodes10.1016/j.jpowsour.2014.10.040 ↗
26. Structure/property relationship of Nafion XL composite membranes10.1016/j.memsci.2016.06.004 ↗
27. Khattra NS, Lu Z, Karlsson AM, Santare MH, Busby FC, Schmiedel T. Time-dependent mechanical response of a composite PFSA membrane. J. Power Sources n.d.;228:256–269. doi:10.1016/j.jpowsour.2012.11.116.10.1016/j.jpowsour.2012.11.116 ↗
28. Mechanical properties of a reinforced composite polymer electrolyte membrane and its simulated performance in PEM fuel cells10.1016/j.jpowsour.2007.09.093 ↗
29. A structure and durability comparison of membrane electrode assembly fabrication methods: self-assembled versus hot-pressed10.1149/2.0051806jes ↗
30. Fuel · 2013
31. Importance of electrode hot-pressing conditions for the catalyst performance of proton exchange membrane fuel cells10.1016/j.apcatb.2015.02.023 ↗
32. Effects of membrane electrode assembly components on proton exchange membrane fuel cell performance10.1016/j.ijhydene.2007.08.021 ↗
33. Temperature dependent performance and in situ AC impedance of high-temperature PEM fuel cells using the nafion-112 membrane10.1149/1.2337008 ↗
34. Improvement of the proton exchange membrane fuel cell performances by optimization of the hot pressing process for membrane electrode assembly10.1007/s10008-013-2273-2 ↗
35. Investigation of hot pressed polymer electrolyte fuel cell assemblies via X-ray computed tomography10.1016/j.electacta.2017.05.028 ↗
36. Static friction force between catalyst layer and micro porous layer and its effect on deformations of membrane electrode assemblies under swelling10.1016/j.jpowsour.2014.08.103 ↗
37. 4D in situ visualization of electrode morphology changes during accelerated degradation in fuel cells by X-ray computed tomography10.1016/j.jpowsour.2017.03.058 ↗
38. Communication—effect of micro-XCT X-ray exposure on the performance of polymer electrolyte fuel cells10.1149/2.0751610jes ↗
39. Aspects of fatigue failure mechanisms in polymer fuel cell membranes10.1002/polb.22336 ↗
40. Khorasany · 2017
41. Viscoelastic stress analysis of constrained proton exchange membranes under humidity cycling10.1115/1.2971045 ↗
42. On the constitutive relations for catalyst coated membrane applied to in-situ fuel cell modeling10.1016/j.jpowsour.2013.11.087 ↗
43. Investigation of membrane degradation in polymer electrolyte fuel cells using local gas permeation analysis10.1016/j.jpowsour.2012.03.071 ↗