journal article·2019-12

A high-performance membrane electrode assembly for polymer electrolyte membrane fuel cell with poly(arylene ether sulfone) nanofibers as effective membrane reinforcements

Yang Zhao, Xue Li, WeiWei Li, Zhongyang Wang, Shubo Wang, Xiaofeng Xie, Vijay Ramani

Publisher page

Abstract

Abstract Direct membrane deposition was recently introduced as a novel polymer electrolyte membrane fabrication method. This method is extended to fabricate a high-performance membrane electrode assembly for polymer electrolyte membrane fuel cell with poly(arylene ether sulfone) nanofibers as effective membrane reinforcements. The nanofibers are directly electrospun onto gas diffusion electrodes. By spray-coating ionomer dispersion into the pore space of nanofiber mats, composite membranes of 15 μm thickness are fabricated. The introduction of the electrically and ionically insulating nanofibers do not hamper the cell performance. At 80 °C and 75% relative humidity, the power density of the fuel cell employing direct membrane deposition, 2.85 W cm−2, is about 1.36 times higher than that of the reference fuel cell (2.09 W cm−2) with Nafion® 211 membrane and identical catalyst. Its cell resistance (28 mΩ cm2) is much lower than that of the membrane electrode assembly fabricated by the catalyst coating membrane method (46 mΩ cm2). The performance differences between two fabrication methods are systematically analyzed by electrochemical impedance spectroscopy. Most notably, even though the thickness of the polymer electrolyte is much lower than that of Nafion® 211 (25 μm), it shows much higher internal short resistance and better durability because of the existence of reinforcement.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Fuel Cells and Related Materials · Electrocatalysts for Energy Conversion · Advanced battery technologies research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (39)

Show source-provided references
1. Enhancement of the electrochemical membrane electrode assembly in proton exchange membrane fuel cells through direct microwave treatment10.1016/j.jpowsour.2014.04.016 ↗
2. Enhanced performance of polybenzimidazole-based high temperature proton exchange membrane fuel cell with gas diffusion electrodes prepared by automatic catalyst spraying under irradiation technique10.1016/j.jpowsour.2013.05.128 ↗
3. Low platinum loading for high temperature proton exchange membrane fuel cell developed by ultrasonic spray coating technique10.1016/j.jpowsour.2014.05.086 ↗
4. Fabrication and performance of catalyst-coated membranes by layer-by-layer deposition of catalyst onto Nafion for polymer electrolyte membrane fuel cells10.1016/j.jpowsour.2011.10.116 ↗
5. Mechanical properties of catalyst coated membranes for fuel cells10.1016/j.jpowsour.2013.01.128 ↗
6. Membrane electrode assembly with enhanced platinum utilization for high temperature proton exchange membrane fuel cell prepared by catalyst coating membrane method10.1016/j.jpowsour.2014.05.014 ↗
7. Spray deposition of Nafion membranes: electrode-supported fuel cells10.1016/j.jpowsour.2016.07.059 ↗
8. Development of thin, reinforced PEMFC membranes through understanding of structure-property-performance relationships[J]10.1149/05002.0051ecst ↗
9. Direct deposition of proton exchange membranes enabling high performance hydrogen fuel cells10.1039/C5TA01341K ↗
10. Direct membrane deposition - a fast and simple technique for membrane electrode assembly manufacturing10.1149/08008.0571ecst ↗
11. Improved Pt-utilization efficiency of low Pt-loading PEM fuel cell electrodes using direct membrane deposition10.1016/j.elecom.2015.09.006 ↗
12. Directly deposited Nafion/TiO2 composite membranes for high power medium temperature fuel cells10.1039/C5RA27462A ↗
13. The reasons for the high power density of fuel cells fabricated with directly deposited membranes10.1016/j.jpowsour.2016.06.132 ↗
14. Simple fabrication of 12 μm thin nanocomposite fuel cell membranes by direct electrospinning and printing10.1016/j.jpowsour.2016.10.094 ↗
15. Electrospun sulfonated poly(ether ketone) nanofibers as proton conductive reinforcement for durable Nafion composite membranes10.1016/j.jpowsour.2017.06.080 ↗
16. Cerium oxide decorated polymer nanofibers as effective membrane reinforcement for durable, high-performance fuel cells10.1002/aenm.201602100 ↗
17. Ageing and thermal conductivity of porous transport layers used for PEM fuel cells10.1016/j.jpowsour.2012.08.027 ↗
18. Nafion/PVDF nanofiber composite membranes for regenerative hydrogen/bromine fuel cells10.1016/j.memsci.2015.04.044 ↗
19. Poly (vinylidene fluoride-co-hexafluoropropylene)/polybenzimidazole blend nanofiber supported Nafion membranes for direct methanol fuel cells10.1016/j.jpowsour.2014.01.104 ↗
20. Sulfonated poly(2,6-dimethyl-1,4-phenylene oxide) (SPPO) electrolyte membranes reinforced by electrospun nanofiber porous substrates for fuel cells10.1016/j.memsci.2010.11.017 ↗
21. Nanofiber network ion-exchange membranes10.1021/ma800551w ↗
22. SiO2/sulfonated poly ether ether ketone (SPEEK) composite nanofiber mat supported proton exchange membranes for fuel cells10.1007/s10853-013-7162-7 ↗
23. Sulfonated poly(arylene ether sulfone) nanocomposite electrolyte membrane for fuel cell applications: a review10.1016/j.ijhydene.2016.10.038 ↗
24. Polymer electrolyte fuel cell performance of poly(arylene ether ketone)-graft-crosslinked-poly(sulfonated arylene ether sulfone)10.1016/j.jpowsour.2013.08.121 ↗
25. Experimental study on the membrane electrode assembly of a proton exchange membrane fuel cell: effects of microporous layer, membrane thickness and gas diffusion layer hydrophobic treatment10.1016/j.electacta.2016.12.074 ↗
26. Preparation of graft poly(arylene ether sulfone)s-based copolymer with enhanced phase-separated morphology as proton exchange membranes via atom transfer radical polymerization10.3390/polym11081297 ↗
27. Polymer electrolyte membranes based on poly(arylene ether)s with flexible disulfophenyl pendant10.1016/j.jpowsour.2014.03.100 ↗
28. Effect of molecular weight on fibrous PVA produced by electrospinning10.1016/S0167-577X(03)00532-9 ↗
29. A fully spray-coated fuel cell membrane electrode assembly using Aquivion ionomer with a graphene oxide/cerium oxide interlayer10.1016/j.jpowsour.2017.03.085 ↗
30. Thin pore-filling membrane with highly packed-acid structure for high temperature and low humidity operating polymer electrolyte fuel cells10.1016/j.jpowsour.2018.05.013 ↗
31. Experimental diagnostics and modeling of inductive phenomena at low frequencies in impedance spectra of proton exchange membrane fuel cells10.1016/j.jpowsour.2017.08.087 ↗
32. 3 in situ and operando determination of the water content distribution in proton conducting membranes for fuel cells: a critical review10.1039/c2ee21834h ↗
33. Effect of elevated temperature and reduced relative humidity on ORR kinetics for PEM fuel cells10.1149/1.1984351 ↗
34. Analysis of oxygen-transport diffusion resistance in proton-exchange-membrane fuel cells10.1149/1.3546038 ↗
35. Influence of convection through gas-diffusion layers on limiting current in PEMFCs using a serpentine flow field10.1149/1.1789791 ↗
36. PEM fuel cell open circuit voltage (OCV) in the temperature range of 23°C to 120°C10.1016/j.jpowsour.2006.09.026 ↗
37. Effects of operating parameters on hydrogen crossover rate through Nafion® membranes in polymer electrolyte membrane fuel cells10.1016/j.renene.2013.01.046 ↗
38. Water management in novel direct membrane deposition fuel cells under low humidification10.1016/j.ijhydene.2016.05.018 ↗
39. A review of water flooding issues in the proton exchange membrane fuel cell10.1016/j.jpowsour.2007.12.068 ↗