Effect of packaging and cooling plates on mechanical response and failure characteristics of automotive Li-ion battery modules
Source abstract
Abstract
Abstract When a battery pack is subjected to external mechanical load, i.e. as in the case of crash, the individual cells experience significant deformations leading to the internal short circuit and possibly fire. The current investigation looks into effects of the inactive components (i.e. cooling plates and module protective enclosure) on deformation and failure of individual pouch cells. Experiments on large spherical indentation of electric vehicle battery module with and without such components have been performed. The results show that the presence of cooling plates overall reduces the force under out-of-plane indentation by approximately a factor of 1.5. It was established however that the failure in cells occurs at the same displacement of the indenter, regardless of the presence of the inactive elements in battery module structure. This underlines the necessity for formulation of the failure criterion based on critical strain, rather than critical stress measure. The findings suggest possibility of utilizing such battery modules in impact energy absorption scenarios, due to reduction in force by the cooling components. X-Ray computed tomography (XCT) has been performed on the cells as a non-destructive analysis of internal failure and the differences of failure mode induced by introduction of structural components are discussed.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Battery Technologies Research · Mechanical Failure Analysis and Simulation · Mechanical Engineering and Vibrations Research
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (37)
Show source-provided references
1. Design of electrolyte solutions for Li and Li-ion batteries: a review10.1016/j.electacta.2004.01.090 ↗
2. A review on the separators of liquid electrolyte Li-ion batteries10.1016/j.jpowsour.2006.10.065 ↗
3. ASTM D4830/D4830M 98 · 2014
4. Baldwin · 2010 · 216099
5. Rate- and temperature-dependent material behavior of a multilayer polymer battery separator10.1007/s11665-013-0743-4 ↗
6. Mechanical properties of a battery separator under compression and tension10.1149/2.0191411jes ↗
7. Deformation and fracture behaviors of microporous polymer separators for lithium ion batteries10.1039/c4ra00983e ↗
8. Mechanical behavior and failure mechanisms of Li-ion battery separators10.1016/j.jpowsour.2017.03.003 ↗
9. Mechanical behavior of a battery separator in electrolyte solutions10.1016/j.jpowsour.2011.06.026 ↗
10. A coupled penetration-tension method for evaluating the reliability of battery separators10.1149/2.012405eel ↗
11. Strain distribution and failure mode of polymer separators for Li-ion batteries under biaxial loading10.1016/j.jpowsour.2017.12.029 ↗
12. Li-ion battery separators, mechanical integrity and failure mechanisms leading to soft and hard internal shorts10.1038/srep32578 ↗
13. Mechanical behavior of representative volume elements of lithiumion battery modules under various loading conditions10.1016/j.jpowsour.2013.09.128 ↗
14. Microscale failure mechanisms leading to internal short circuit in Li-ion batteries under complex loading scenarios10.1016/j.jpowsour.2016.04.005 ↗
15. Doughty · 2006
16. UN 38.3 · 2009 · 394
17. Evaluation of mechanical abuse techniques in lithium ion batteries10.1016/j.jpowsour.2013.08.066 ↗
18. Building a ”smart nail” for penetration tests on Li-ion cells10.1016/j.jpowsour.2013.09.022 ↗
19. Internal short circuit in Li ion cells10.1016/j.jpowsour.2009.02.070 ↗
20. Experimental simulation of internal short circuit in Li-ion and Li-ion-polymer cell10.1016/j.jpowsour.2011.04.024 ↗
21. 1625-2008 · 2015
22. Study of internal short in a Li-ion cell I. Test method development using infra-red imaging technique10.1016/j.jpowsour.2013.09.145 ↗
23. Characterizing thermal runaway within lithium-ion cells by inducing and monitoring internal short circuits10.1039/C7EE00385D ↗
24. Progressive mechanical indentation of large-format Li-ion cells10.1016/j.jpowsour.2016.11.094 ↗
25. Calibration and finite element simulation of pouch lithium-ion batteries for mechanical integrity10.1016/j.jpowsour.2011.10.094 ↗
26. Characterizing and modeling mechanical properties and onset of short circuit for three types of lithium-ion pouch cells10.1016/j.jpowsour.2013.08.056 ↗
27. Computational models for simulations of lithium-ion battery cells under constrained compression tests10.1016/j.jpowsour.2013.05.022 ↗
28. Modelling of cracks developed in lithium-ion cells under mechanical loading10.1039/C5RA17865G ↗
29. Indentation of Li-ion pouch cell: effect of material homogenization on prediction of internal short circuit10.1149/2.0151613jes ↗
30. Coupled mechanical-electrical-thermal modeling for short-circuit prediction in a lithium-ion cell under mechanical abuse10.1016/j.jpowsour.2015.04.162 ↗
31. Damage of cells and battery packs due to ground impact10.1016/j.jpowsour.2014.05.078 ↗
32. Failure behaviours of 100% SOC lithium-ion battery modules under different impact loading conditions10.1016/j.engfailanal.2017.09.003 ↗
33. A review of safety-focused mechanical modeling of commercial lithium-ion batteries10.1016/j.jpowsour.2017.12.034 ↗
34. Scout and Scan Control System, v.11.1.5534.17006, Carl Zeiss X-Ray Microscopy, Pleasanton, CA 94588, USA.
35. TXM3DViewer 1.2.9, Carl Zeiss X-Ray Microscopy, Pleasanton, CA 94588, USA.
36. 2017
37. Failure of cemented granular materials under simple compression: experiments and numerical simulations10.1007/s00707-009-0160-9 ↗