journal article·2015-10

Novel light-weight, high-performance anode-supported microtubular solid oxide fuel cells with an active anode functional layer

Tong Liu, Yao Wang, Cong Ren, Shumin Fang, Yating Mao, Fanglin Chen

Publisher page

Abstract

Abstract Influence of the air-gap, the distance from the tube-in-orifice spinneret to the upper surface of the external coagulant bath during the extrusion/phase-inversion process, on the microstructure of nickel – yttria-stabilized zirconia (Ni–YSZ) hollow fibers has been systematically studied. When the air-gap is 0 cm, the obtained Ni–YSZ hollow fiber has a sandwich microstructure. However, when the air-gap is increased to 15 cm, a bi-layer Ni–YSZ hollow fiber consisting of a thin layer with small pores and a thick support with highly porous fingerlike macrovoids has been achieved. The output power density of microtubular solid oxide fuel cells (MT-SOFCs) with a cell configuration of Ni–YSZ/YSZ/YSZ–LSM increases from 594 mW cm−2 for the cells with the Ni–YSZ anode of sandwich microstructure to 832 mW cm−2 for the cells with the Ni–YSZ anode of bi-layer microstructure at 750 °C, implying that to achieve the same output power density, the weight of the cells with the bi-layer anode support can be reduced to 41.5% compared with that of the cells with the sandwich anode support. Thermal-cycling test shows no obvious degradation on the open-circuit-voltage (OCV), indicating that the MT-SOFCs have robust resistance to thermal cycling.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advancements in Solid Oxide Fuel Cells · Electronic and Structural Properties of Oxides · Catalysis and Oxidation Reactions

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (32)

Show source-provided references
1. Singhal · 2003
2. An octane-fueled solid oxide fuel cell10.1126/science.1109213 ↗
3. A novel electrode material for symmetrical SOFCs10.1002/adma.201001044 ↗
4. Materials for fuel-cell technologies10.1038/35104620 ↗
5. Impact of anode microstructure on solid oxide fuel cells10.1126/science.1176404 ↗
6. High-performance, anode-supported, microtubular SOFC prepared from single-step-fabricated, dual-layer hollow fibers10.1002/adma.201100194 ↗
7. Microstructure tailoring of the nickel oxide (NiO)-yttria stabilized zirconia (YSZ) hollow fibers towards high-performance micro-tubular solid oxide fuel cells10.1021/am5046907 ↗
8. Effect of casting slurry composition on anode support microstructure and cell performance of MT-SOFCs by phase inversion method10.1016/j.electacta.2014.10.060 ↗
9. Novel functionally graded acicular electrode for solid oxide cells fabricated by the freeze-tape-casting process10.1016/j.jpowsour.2012.03.109 ↗
10. High performance low temperature solid oxide fuel cells with novel electrode architecture10.1039/c2ra21921b ↗
11. A 1000-cell SOFC reactor for domestic cogeneration10.1016/S0378-7753(97)02756-0 ↗
12. Cycling of three solid oxide fuel cell types10.1016/j.jpowsour.2007.01.029 ↗
13. Intermediate temperature micro-tubular SOFCs with enhanced performance and thermal stability10.1016/j.elecom.2013.06.015 ↗
14. Fabrication of needle-type micro SOFCs for micro power devices10.1016/j.elecom.2008.08.016 ↗
15. Novel cathode-supported hollow fibers for light weight micro-tubular solid oxide fuel cells with an active cathode functional layer10.1039/C4TA04635H ↗
16. A dual-structured anode/Ni-mesh current collector hollow fibre for micro-tubular solid oxide fuel cells (SOFCs)10.1016/j.jpowsour.2013.11.043 ↗
17. Micro-tubular solid oxide fuel cells fabricated by phase-inversion method10.1016/j.elecom.2010.02.024 ↗
18. Microchanneled anode supports of solid oxide fuel cells10.1016/j.elecom.2014.02.013 ↗
19. A morphological study of ceramic hollow fibre membranes10.1016/j.memsci.2008.11.050 ↗
20. An investigation on dip-coating technique for fabricating anode-supported solid oxide fuel cells10.1111/ijac.12147 ↗
21. Microstructure control of oxygen permeation membranes with templated microchannels10.1039/C3TA13744A ↗
22. Fabrication and characterization of an anode-supported hollow fiber SOFC10.1016/j.jpowsour.2008.10.069 ↗
23. Single-step fabrication and characterisations of electrolyte/anode dual-layer hollow fibres for micro-tubular solid oxide fuel cells10.1016/j.memsci.2010.01.050 ↗
24. Materials for solid oxide fuel cells10.1021/cm902640j ↗
25. High performance anode-supported tubular solid oxide fuel cells fabricated by a novel slurry-casting method10.1038/srep08174 ↗
26. An anode-supported solid oxide fuel cell with spray-coated yttria-stabilized zirconia (YSZ) electrolyte film10.1016/j.ssi.2008.01.094 ↗
27. Facile one-step forming of NiO and yttrium-stabilized zirconia composite anodes with straight open pores for planar solid oxide fuel cell using phase-inversion tape casting method10.1016/j.jpowsour.2014.10.190 ↗
28. Performances of micro-tubular solid oxide cell with novel asymmetric porous hydrogen electrode10.1016/j.electacta.2010.09.052 ↗
29. Effects on microstructure of NiO–YSZ anode support fabricated by phase-inversion method10.1016/j.memsci.2010.07.044 ↗
30. Microstructure tailoring of YSZ/Ni-YSZ dual-layer hollow fibers for micro-tubular solid oxide fuel cell application10.1016/j.ijhydene.2013.03.088 ↗
31. Effect of PEG additive on anode microstructure and cell performance of anode-supported MT-SOFCs fabricated by phase inversion method10.1016/j.jpowsour.2014.12.140 ↗
32. Microtubular solid oxide fuel cells with lanthanum strontium manganite infiltrated cathodes10.1016/j.ijhydene.2015.01.060 ↗