Simulation of the water and heat management in proton exchange membrane fuel cells
Source abstract
Abstract
A non-isothermal and three-dimensional numerical model of a PEM fuel cell was developed to compute the water and heat management. Transport of water in the polymer membrane, phase change of water in the cathode porous medium and capillary flow to the gas channels were determined. Influences of these phenomena on fuel cells and conditions that may affect their performance have been numerically evaluated. Output variables are velocity, temperature, mass fraction, current density, voltage loss, water content of the polymer membrane, saturation and liquid flow fields. Cell voltage and total current density of PEM fuel cell were computed as well. Results show that there may be severe mass transfer limitations depending either on the design or on the water management of the cell. For the chosen conditions, the polymer membrane can keep and even increase its water content, as long as inlet flows are injected at 100% relative humidity. In case the fuel cell is operated under dehydrating conditions, the decrease of the water content of the polymer electrolyte may affect the performance. The variations of temperature were small. However, temperature plays an important role in the cathode reaction rate of the cell and in the dehydration of the polymer membrane. Numerical results and experimental data were found to be in good agreement.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Fuel Cells and Related Materials · Electrocatalysts for Energy Conversion · Advanced battery technologies research
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (23)
Show source-provided references
1. Simulation und Messung thermofluiddynamischer Vorgänge zur Optimierung des Flowfields von PEM-Brennstoffzellen
2. Two-phase modeling and flooding prediction of polymer electrolyte fuel cells10.1149/1.1850339 ↗
3. Fundamental models for fuel cell engineering10.1021/cr020718s ↗
4. Two-phase flow and transport in the air cathode of proton exchange membrane fuel cells10.1016/S0378-7753(00)00662-5 ↗
5. A two-dimensional, two-phase, multicomponent, transient model for the cathode of a proton exchange membrane fuel cell using conventional gas distributors10.1149/1.1415032 ↗
6. A 3D multiphase, multicomponent model of the cathode and anode of a PEM fuel cell10.1149/1.1621412 ↗
7. Effective diffusivity and water-saturation distribution in single- and two-layer PEMFC diffusion medium10.1016/S0017-9310(03)00305-3 ↗
8. Ordinary and transition regime diffusion in random fiber structures10.1002/aic.690390304 ↗
9. Bird · 1960
10. Polymer electrolyte fuel cell model10.1149/1.2085971 ↗
11. W. Neubrand, Modellierung und Simulation von Electromembranverfahren, Dissertation, Universität Stuttgart, Germany, 1999.
12. Water uptake by and transport through Nafion 117 membranes10.1149/1.2056194 ↗
13. Water uptake of perfluorosulfonic acid membranes from liquid water and water vapour10.1149/1.2054951 ↗
14. A mathematical model and optimization of the cathode catalyst layer structure in PEM fuel cells10.1016/j.electacta.2004.01.113 ↗
15. Investigation of mass-transport limitations in the solid polymer fuel cell cathode10.1149/1.1456916 ↗
16. Composition and performance modeling of a catalyst layer in a proton exchange membrane fuel cell10.1016/S0378-7753(98)00161-X ↗
17. Mass transport in gas-diffusion electrodes: a diagnostic tool for fuel-cell cathodes10.1149/1.1838202 ↗
18. Modeling the PEM fuel cell cathode10.1023/A:1018476612810 ↗
19. Mathematical model of the solid polymer electrolyte fuel cell10.1149/1.2221251 ↗
20. Temperature dependence of the electrode kinetics of oxygen reduction at the Platinum/Nafion interface—a microelectrode investigation10.1149/1.2221258 ↗
21. Patankar · 1980
22. Modeling polymer electrolyte fuel cells with large density and velocity changes10.1149/1.1851059 ↗
23. A novel polymer electrolyte fuel cell for laboratory investigations and in situ contact resistance measurements10.1016/S0013-4686(01)00510-2 ↗