Experimental and numerical study on catalyst layer of polymer electrolyte membrane fuel cell prepared with diverse drying methods
Source abstract
Abstract
Abstract High manufacturing cost is a major challenge to commercialization of the polymer electrolyte membrane fuel cell (PEMFC) technology in high volume market. Catalyst layer (CL) of PEMFC should incorporate high effective porosity, electrochemically active surface-area, gas permeability, and favorable ionomer distribution. Drying of the CL is a very significant step of electrode fabrication, and determines most of the properties mentioned above, but is rarely a subject of investigation. From various possible drying processes of CL, freeze-drying shows some beneficial properties, such as higher porosity, better ionomer distribution, and reduces the mass transport resistance significantly by allowing more reactant gas into reactive interface. In this work, the influence of diverse drying techniques on the microstructure and performance is investigated. Complementarily, a transient 2D physical continuum-model is used to investigate the effect of the structural properties on cell performance of electrodes prepared with different drying methods. A sensitivity analysis has been also performed to determine the influence of individual parameters applied in the model. Both of the experimental and simulation results stress on the fact that the freeze-drying technique not only significantly enhances the oxygen transport properties through ionomer but also improves the porosity along with the tortuosity of the CL microstructure.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Fuel Cells and Related Materials · Electrocatalysts for Energy Conversion · Advancements in Solid Oxide Fuel Cells
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (56)
Show source-provided references
1. PEM fuel cell electrodes10.1016/j.jpowsour.2003.12.055 ↗
2. Modeling and experimental diagnostics in polymer electrolyte fuel cells10.1149/1.2221120 ↗
3. Composition and performance modelling of catalyst layer in a proton exchange membrane fuel cell10.1016/S0378-7753(98)00161-X ↗
4. Analysis of the microstructure formation process and its influence on the performance of polymer electrolyte fuel-cell catalyst layers10.1002/celc.201500131 ↗
5. The priority and challenge of high-power performance of low-platinum proton-exchange membrane fuel cells10.1021/acs.jpclett.6b00216 ↗
6. Review and analysis of PEM fuel cell design and manufacturing10.1016/S0378-7753(02)00542-6 ↗
7. An evaluation of the macro-homogeneous and agglomerate model for oxygen reduction in PEMFCs10.1016/S0013-4686(98)00136-4 ↗
8. Gas diffusion electrodes and membrane electrode assemblies based on a sulfonated polysulfone for high-temperature PEMFC
9. Effect of Pt loading and catalyst type on the pore structure of porous electrodes in polymer electrolyte membrane (PEM) fuel cells10.1016/j.energy.2018.02.134 ↗
10. The air/platinum/nafion triple-phase boundary: characteristics, scaling, and implications for fuel cells10.1149/1.1701868 ↗
11. Polyacrylamide/Nafion® semi-interpenetrating networks as proton-conducting membrane of direct methanol fuel cell10.1166/sam.2014.2190 ↗
12. PEMFC catalyst layers: the role of micropores and mesopores on water sorption and fuel cell activity10.1021/am200590w ↗
13. Wang · 2015
14. Proton-Conducting membranes from nafion®/polystyrene sulfonate composite for fuel cell applications10.1166/jno.2015.1797 ↗
15. Minimizing mass-transport loss in proton exchange membrane fuel cell by freeze-drying of cathode catalyst layers10.1016/j.jpowsour.2019.04.094 ↗
16. Enveloping of catalyst powder by ionomer for dry spray coating in polymer electrolyte membrane fuel cells10.1016/j.jpowsour.2019.03.093 ↗
17. Rational design of a highly efficient Pt/graphene-Nafion® composite fuel cell electrode architecture10.1039/C4TA05399K ↗
18. Freeze-drying of nanoparticles: formulation, process and storage considerations10.1016/j.addr.2006.09.017 ↗
19. Controlling the distribution of perfluorinated sulfonic acid ionomer with elastin-like polypeptide10.1021/acsami.9b11160 ↗
20. PEMFC electrode preparation: influence of the solvent composition and evaporation rate on the catalytic layer microstructure10.1016/j.jpowsour.2005.02.048 ↗
21. Performance enhancement of PEMFC through temperature control in catalyst layer fabrication10.1016/j.electacta.2007.07.046 ↗
22. Modeling air electrodes with low platinum loading10.1149/2.0101907jes ↗
23. Fuel cell catalyst layers: a polymer science perspective10.1021/cm401445h ↗
24. Effects of cathode catalyst layer structure and properties dominating polymer electrolyte fuel cell performance10.1149/1.3624606 ↗
25. A critical review of modeling transport phenomena in polymer-electrolyte fuel cells10.1149/2.0751412jes ↗
26. Free open reference implementation of a two-phase PEM fuel cell model10.1016/j.cpc.2018.07.023 ↗
27. Microstructure of catalyst layers in PEM fuel cells redefined: a computational approach10.1007/s12678-011-0047-0 ↗
28. Review of characterization and modeling of polymer electrolyte fuel cell catalyst layer: the blessing and curse of ionomer10.1007/s11708-017-0490-6 ↗
29. Physical modeling of polymer-electrolyte membrane fuel cells: understanding water management and impedance spectra10.1016/j.jpowsour.2018.04.070 ↗
30. Optimum Nafion content in PEM fuel cell electrodes10.1016/j.electacta.2004.01.126 ↗
31. Physical chemistry of freeze‐drying: measurement of sublimation rates for frozen aqueous solutions by a microbalance technique10.1002/jps.2600720614 ↗
32. Critical freezing rate in freeze drying nanocrystal dispersions10.1016/j.jconrel.2005.12.003 ↗
33. An improved method for the calculation of pore size distribution from adsorption data10.1002/jctb.5010140302 ↗
34. On the micro-, meso-, and macroporous structures of polymer electrolyte membrane fuel cell catalyst layers10.1021/am900600y ↗
35. Effect of gas diffusion layer compression on PEM fuel cell performance10.1016/j.jpowsour.2005.11.069 ↗
36. Impact of compressive stress on MEA pore structure and its consequence on PEMFC performance10.1149/2.0291608jes ↗
37. The role of compressive stress on gas diffusion media morphology and fuel cell performance10.1021/acsaem.7b00077 ↗
38. Influence of the gas diffusion layer compression on the oxygen transport in PEM fuel cells at high water saturation levels10.1149/2.0691706jes ↗
39. Ionic conductivity of PEMFC electrodes effect of Nafion loading10.1149/1.1611493 ↗
40. Comparative investigation into the performance and durability of long and short side chain ionomers in Polymer Electrolyte Membrane Fuel Cells10.1016/j.jpowsour.2019.227078 ↗
41. Artifacts in measuring electrode catalyst area of fuel cells through cyclic voltammetry10.1149/1.2780954 ↗
42. Cooper · 2009 · 1
43. Breitkopf · 2016
44. Bird · 2006
45. A physics-based impedance model of proton exchange membrane fuel cells exhibiting low-frequency inductive loops10.1149/2.0361506jes ↗
46. Fabrication of microstructure controlled cathode catalyst layers and their effect on water management in polymer electrolyte fuel cells10.1016/j.electacta.2011.05.123 ↗
47. Porosity and catalyst utilization of thin layer cathodes in air operated PEM-fuel cells10.1023/A:1003259531775 ↗
48. Influence of the gas diffusion layer compression on the oxygen transport in PEM fuel cells at high water saturation levels10.1149/2.0691706jes ↗
49. Fuel cell catalyst layers: a polymer science perspective10.1021/cm401445h ↗
50. Electrochemical impedance of the cathode catalyst layer in polymer electrolyte fuel cells10.1016/S0022-0728(99)00335-6 ↗
51. Darling
52. Electrochemical characterization of MEAs with different Pt-loading for the efficient use of Pt10.1149/08008.0789ecst ↗
53. Characterization of ionic conductivity profiles within proton exchange membrane fuel cell gas diffusion electrodes by impedance spectroscopy10.1149/1.1390804 ↗
54. Investigation of porous structure formation of catalyst layers for proton exchange membrane fuel cells and their effect on cell performance10.1016/j.ijhydene.2016.09.078 ↗
55. Boosting fuel cell performance with accessible carbon mesopores10.1021/acsenergylett.8b00186 ↗
56. Effects of carbon supports on Pt distribution, ionomer coverage and cathode performance for polymer electrolyte fuel cells10.1016/j.jpowsour.2016.02.091 ↗