Sliding mode observer for proton exchange membrane fuel cell: automotive application
Source abstract
Abstract
This work proposes a state observer as a tool to manage cost and durability issues for PEMFC (Proton Exchange Membrane Fuel Cell) in automotive applications. Based on a dead-end anode architecture, the observer estimates the nitrogen build-up in the anode side, as well as relative humidities in the channels. These estimated parameters can then be used at fuel cell management level to enhance the durability of the stack. This observer is based on transport equations through the membrane and it reconstructs the behavior of the water and nitrogen inside the channels without the need of additional humidity sensors to correct the estimate. The convergence of the output variables is proved with Lyapunov theory for dynamic operating conditions. The validation is made with a high-fidelity model running a WLTC (Worldwide harmonized Light vehicles Test Cycle). This observer provide the average values of nitrogen and relative humidities with sufficient precision to be used in a global real-time control scheme.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Fuel Cells and Related Materials · Electrocatalysts for Energy Conversion · Advancements in Solid Oxide Fuel Cells
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (20)
Show source-provided references
1. A review on fuel cell technologies and power electronic interface10.1016/j.rser.2009.04.004 ↗
2. Fuel processing activities at european level: a panoramic overview10.1016/j.ijhydene.2014.04.040 ↗
3. Experimental study of hydrogen purge effects on performance and efficiency of an open-cathode proton exchange membrane fuel cell system10.1016/j.jpowsour.2013.09.122 ↗
4. Degradation phenomena in pem fuel cell with dead-ended anode10.1016/j.ijhydene.2013.06.096 ↗
5. Optimization of purge cycle for dead-ended anode fuel cell operation10.1016/j.ijhydene.2013.02.022 ↗
6. Optimization study of purge cycle in proton exchange membrane fuel cell system10.1016/j.jpowsour.2012.11.153 ↗
7. Buildup of nitrogen in direct hydrogen polymer-electrolyte fuel cell stacks10.1016/j.jpowsour.2007.01.032 ↗
8. Optimization of fuel cell system operating conditions for fuel cell vehicles10.1016/j.jpowsour.2008.10.032 ↗
9. Toward the optimization of operating conditions for hydrogen polymer electrolyte fuel cells10.1016/j.jpowsour.2005.05.091 ↗
10. Model development and optimization of operating conditions to maximize PEMFC performance by response surface methodology10.1016/j.enconman.2014.12.093 ↗
11. Diagnosis of polymer electrolyte fuel cells failure modes (flooding and drying out) by neural networks modeling10.1016/j.ijhydene.2010.10.077 ↗
12. Nonlinear distributed parameter observer design for fuel cell systems10.1016/j.ijhydene.2015.05.132 ↗
13. Control by state observer of PEMFC anodic purges in dead-end operating mode10.1016/j.ifacol.2015.10.034 ↗
14. Fuel cell operation characterization using simulation10.1016/j.jpowsour.2005.08.034 ↗
15. Multi-scale coupling between two dynamical models for PEMFC aging prediction10.1016/j.ijhydene.2013.01.040 ↗
16. Development and experimental validation of a PEM fuel cell 2d-model to study heterogeneities effects along large-area cell surface10.1016/j.ijhydene.2015.05.178 ↗
17. Electrical test methods for on-line fuel cell ohmic resistance measurement10.1016/j.jpowsour.2006.02.086 ↗
18. Hedrick · 2005
19. Development of the world-wide harmonized light duty test cycle (wltc) and a possible pathway for its introduction in the european legislation10.1016/j.trd.2015.07.011 ↗
20. Nitrogen blanketing front equilibria in dead end anode fuel cell operation