journal article·2019-08

Polydopamine-treated three-dimensional carbon fiber-coated separator for achieving high-performance lithium metal batteries

Jeonghun Oh, Hearin Jo, Hongkyung Lee, Hee-Tak Kim, Yong Min Lee, Myung-Hyun Ryou

Publisher page

Abstract

Abstract The development of safe and high-performance lithium (Li) metal anodes has been a challenging issue that has not been addressed for decades. In this study, we have developed a thermally stable polydopamine-treated three-dimensional (3D) carbon fiber-coated separator (P3D-CFS) using an economical and environment-friendly process. P3D-CFS has a conductive coating layer that is used as a 3D hosting structure, which does not cause morphological changes in the Li metal anode. As a result, the unit cells (LiMn2O4/Li metal) employing P3D-CFS improve the cycle performance and rate capability compared to commercial polyethylene (PE) separators. P3D-CFS maintained 83.1% of the initial discharge capacity at the 400th cycle, whereas bare PE maintains only 74.3% of the initial discharge capacity after the 250th cycle (C/2 = 0.5 mA cm−2). P3D-CFS maintains 42.8% of the initial discharge capacity at a 7C rate (7 mA cm−2), whereas only 0.19% is maintained by bare PE under the same condition. Owing to the thermally stable properties of P3D-CFS, the open-circuit voltage of the unit cells (LiMn2O4/graphite) that employed P3D-CFS is maintained for over 60 min at 140 °C, whereas the unit cells that employed bare PE show a sudden voltage drop after only 3 min.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advancements in Battery Materials · Advanced Battery Materials and Technologies · Advanced Battery Technologies Research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (40)

Show source-provided references
1. Nonaqueous liquid electrolytes for lithium-based rechargeable batteries10.1021/cr030203g ↗
2. Recent progress in advanced electrode materials, separators and electrolytes for lithium batteries10.1039/C8TA05336G ↗
3. A soft non-porous separator and its effectiveness in stabilizing Li metal anodes cycling at 10 mA cm− 2 observed in situ in a capillary cell10.1039/C7TA00069C ↗
4. Review of gel-type polymer electrolytes for lithium-ion batteries10.1016/S0378-7753(98)00193-1 ↗
5. Nanostructured Sn–C composite as an advanced anode material in high‐performance Lithium‐ion batteries10.1002/adma.200700748 ↗
6. A short review of failure mechanisms of lithium metal and lithiated graphite anodes in liquid electrolyte solutions10.1016/S0167-2738(02)00080-2 ↗
7. Dendrite-free lithium deposition via self-healing electrostatic shield mechanism10.1021/ja312241y ↗
8. The synergetic effect of lithium polysulfide and lithium nitrate to prevent lithium dendrite growth10.1038/ncomms8436 ↗
9. Fluoroethylene carbonate additives to render uniform Li deposits in lithium metal batteries10.1002/adfm.201605989 ↗
10. High rate and stable cycling of lithium metal anode10.1038/ncomms7362 ↗
11. Electrolyte additive enabled fast charging and stable cycling lithium metal batteries10.1038/nenergy.2017.12 ↗
12. Non-flammable electrolyte enables Li-metal batteries with aggressive cathode chemistries10.1038/s41565-018-0183-2 ↗
13. Composite protection layers for dendrite-suppressing non-granular micro-patterned lithium metal anodes10.1016/j.electacta.2018.05.102 ↗
14. Micro‐Patterned lithium metal anodes with suppressed dendrite formation for post lithium‐ion batteries10.1002/admi.201600140 ↗
15. Study on dead-Li suppression mechanism of Li-hosting vapor-grown-carbon-nanofiber-based protective layer for Li metal anodes10.1016/j.jpowsour.2018.09.059 ↗
16. Ultrathin two-dimensional atomic crystals as stable interfacial layer for improvement of lithium metal anode10.1021/nl503125u ↗
17. An artificial solid electrolyte interphase layer for stable lithium metal anodes10.1002/adma.201504526 ↗
18. Designer interphases for the lithium-oxygen electrochemical cell10.1126/sciadv.1602809 ↗
19. Artificial soft–rigid protective layer for dendrite‐free lithium metal anode10.1002/adfm.201705838 ↗
20. A facile surface chemistry route to a stabilized lithium metal anode10.1038/nenergy.2017.119 ↗
21. Dual-phase lithium metal anode containing a polysulfide-induced solid electrolyte interphase and nanostructured graphene framework for lithium–sulfur batteries10.1021/acsnano.5b01990 ↗
22. Lithium-coated polymeric matrix as a minimum volume-change and dendrite-free lithium metal anode10.1038/ncomms10992 ↗
23. Layered reduced graphene oxide with nanoscale interlayer gaps as a stable host for lithium metal anodes10.1038/nnano.2016.32 ↗
24. Composite lithium metal anode by melt infusion of lithium into a 3D conducting scaffold with lithiophilic coating10.1073/pnas.1518188113 ↗
25. Mechanical surface modification of lithium metal: towards improved Li metal anode performance by directed Li plating10.1002/adfm.201402953 ↗
26. Accommodating lithium into 3D current collectors with a submicron skeleton towards long-life lithium metal anodes10.1038/ncomms9058 ↗
27. Lithium-metal deposition/dissolution within internal space of CNT 3D matrix results in prolonged cycle of lithium-metal negative electrode10.1016/j.carbon.2017.04.032 ↗
28. Selective deposition and stable encapsulation of lithium through heterogeneous seeded growth10.1038/nenergy.2016.10 ↗
29. Trapping lithium into hollow silica microspheres with a carbon nanotube core for dendrite-free lithium metal anodes10.1021/acs.nanolett.7b04136 ↗
30. A review on the separators of liquid electrolyte Li-ion batteries10.1016/j.jpowsour.2006.10.065 ↗
31. A review of recent developments in membrane separators for rechargeable lithium-ion batteries10.1039/C4EE01432D ↗
32. Conductive porous carbon film as a lithium metal storage medium10.1016/j.electacta.2015.06.140 ↗
33. Excellent cycle life of lithium‐metal anodes in lithium‐ion batteries with mussel‐inspired polydopamine‐coated separators10.1002/aenm.201100687 ↗
34. Mussel‐inspired polydopamine‐treated polyethylene separators for high‐power Li‐ion batteries10.1002/adma.201100303 ↗
35. A water-based Al2O3 ceramic coating for polyethylene-based microporous separators for lithium-ion batteries10.1016/j.jpowsour.2016.03.037 ↗
36. Mussel‐Inspired polydopamine‐functionalized super‐P as a conductive additive for high‐performance silicon anodes10.1002/admi.201600270 ↗
37. Mussel-inspired surface chemistry for multifunctional coatings10.1126/science.1147241 ↗
38. Reviving the lithium metal anode for high-energy batteries10.1038/nnano.2017.16 ↗
39. VGCF 3D conducting host coating on glass fiber filters for lithium metal anodes10.1039/C7CC07828E ↗
40. Stable Li metal anodes via regulating lithium plating/stripping in vertically aligned microchannels10.1002/adma.201703729 ↗