Characterisation of the diffusion properties of metal foam hybrid flow-fields for fuel cells using optical flow visualisation and X-ray computed tomography
Source abstract
Abstract
The flow distribution behaviour of open-cell metallic foam fuel cell flow-fields are evaluated using ex-situ optical analysis and X-ray computed tomography (X-ray CT). Five different manifold designs are evaluated and flow distribution and pressure drop quantitatively evaluated with reference to applications in polymer exchange membrane fuel cells (PEMFC) and heat exchangers. A ‘hybrid’ foam flow-field is presented consisting of flow channels pressed into the foam to promote flow distribution and reduce pressure drop. Cross- and through-channel pressure drop measurements are conducted, along with X-ray CT analysis. Results using dyed water show that metallic foams provide excellent fluid distribution across the fuel cell flow-field, closely following the theoretical filling rate. The time for dye to cover 80% of the flow-field area was 61% faster with a foam flow-field then with no flow-field present. Pressure drop was seen to reduce with increasing foam inlet area to levels comparable to multi-serpentine flow-fields. The introduction of flow channels in the foam can further reduce pressure drop and provide more even filling of the foam, at the expense of increased residence time.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Fuel Cells and Related Materials · Lattice Boltzmann Simulation Studies · Heat and Mass Transfer in Porous Media
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (35)
Show source-provided references
1. Ashby · 2000
2. Porous metals and metallic foams: current status and recent developments10.1002/adem.200800241 ↗
3. Metal foams as compact high performance heat exchangers10.1016/j.mechmat.2003.02.001 ↗
4. Comparison of metal foam heat exchangers to a finned heat exchanger for low Reynolds number applications10.1016/j.ijheatmasstransfer.2015.05.013 ↗
5. Numerical investigation of the temporal evolution of particulate fouling in metal foams for air-cooled heat exchangers10.1016/j.apenergy.2016.10.044 ↗
6. Experimental hydrodynamic study of flow through metallic foams: flow regime transitions and surface roughness influence10.1016/j.mechmat.2016.05.007 ↗
7. Melting heat transfer characteristics of a composite phase change material fabricated by paraffin and metal foam10.1016/j.apenergy.2015.10.075 ↗
8. Metal foam heat exchangers for thermal management of fuel cell systems – an experimental study10.1016/j.expthermflusci.2013.07.016 ↗
9. A study on using metal foam as coolant fluid distributor in the polymer electrolyte membrane fuel cell10.1016/j.ijhydene.2015.10.122 ↗
10. Porous metal materials for polymer electrolyte membrane fuel cells – a review10.1016/j.apenergy.2012.01.073 ↗
11. Metal foams application to enhance cooling of open cathode polymer electrolyte membrane fuel cells10.1016/j.jpowsour.2015.07.022 ↗
12. Low-cost light weight high power density PEM fuel cell stack10.1016/S0013-4686(98)00143-1 ↗
13. Polymer electrolyte membrane fuel cell with metal foam in the gas flow-field of bipolar/end plates
14. Materials and design development for bipolar/end plates in fuel cells10.1016/j.jpowsour.2003.11.011 ↗
15. Modeling of polymer electrolyte membrane fuel cell with metal foam in the flow-field of the bipolar/end plates10.1016/S0378-7753(02)00540-2 ↗
16. A PEM fuel cell with metal foam as flow distributor10.1016/j.enconman.2012.03.018 ↗
17. Graphene as corrosion protection for metal foam flow distributor in proton exchange membrane fuel cells10.1016/j.ijhydene.2017.03.233 ↗
18. Experimental investigation on PEM fuel cell cold start behavior containing porous metal foam as cathode flow distributor10.1016/j.apenergy.2017.06.028 ↗
19. Metal foams as flow field and gas diffusion layer in direct methanol fuel cells10.1016/j.jpowsour.2006.12.008 ↗
20. Performance improvement in direct methanol fuel cells using a highly porous corrosion-resisting stainless steel flow field10.1016/j.ijhydene.2008.03.021 ↗
21. A new application for nickel foam in alkaline fuel cells10.1016/j.ijhydene.2009.06.035 ↗
22. Application of metal foams to high temperature PEM fuel cells10.1016/j.ijhydene.2016.06.149 ↗
23. Effects of flow field design on the performance of a PEM fuel cell with metal foam as the flow distributor10.1016/j.ijhydene.2012.05.008 ↗
24. Effects of the porous structures in the porous flow field type separators on fuel cell performances10.1016/j.ijhydene.2014.07.070 ↗
25. Performance characteristics and internal phenomena of polymer electrolyte membrane fuel cell with porous flow field10.1016/j.jpowsour.2013.03.047 ↗
26. Investigation of hot pressed polymer electrolyte fuel cell assemblies via X-ray computed tomography10.1016/j.electacta.2017.05.028 ↗
27. Effect of gas diffusion layer properties on water distribution across air-cooled, open-cathode polymer electrolyte fuel cells: a combined ex-situ X-ray tomography and in-operando neutron imaging study10.1016/j.electacta.2016.06.068 ↗
28. The effects of gas diffusion layers structure on water transportation using X-ray computed tomography based Lattice Boltzmann method10.1016/j.jpowsour.2017.12.016 ↗
29. Simulation of liquid water breakthrough in a nanotomography reconstruction of a carbon paper gas-diffusion layer10.1002/aic.12581 ↗
30. Street · 1996
31. Lide · 2015
32. Residence time measurement of an isothermal combustor flow field10.1007/s00348-011-1085-3 ↗
33. Fuel gallery residence time & heat transfer experimental technique development for gas turbine fuel injectors
34. Larminie · 2003
35. Full-field measurements of flow through a scaled metal foam replica10.1007/s00348-010-1008-8 ↗