In-situ diagnostics and degradation mapping of a mixed-mode accelerated stress test for proton exchange membranes
Source abstract
Abstract
Abstract With increasing availability of more durable membrane materials for proton exchange membrane fuel cells, there is a need for a more stressful test that combines chemical and mechanical stressors to enable accelerated screening of promising membrane candidates. Equally important is the need for in-situ diagnostic methods with sufficient spatial resolution that can provide insights into how membranes degrade to facilitate the development of durable fuel cell systems. In this article, we report an accelerated membrane stress test and a degradation diagnostic method that satisfy both needs. By applying high-amplitude cycles of electrical load to a fuel cell fed with low-RH reactant gases, a wide range of mechanical and chemical stressful conditions can be created within the cell which leads to rapid degradation of a mechanically robust Ion Power™ N111-IP membrane. Using an in-situ shorting/crossover diagnostic method on a segmented fuel cell fixture that provides 100 local current measurements, we are able to monitor the progression and map the degradation modes of shorting, thinning, and crossover leak over the entire membrane. Results from this test method have been validated by conventional metrics of fluoride release rates, physical crossover leak rates, pinhole mapping, and cross-sectional measurements.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Fuel Cells and Related Materials · Advancements in Solid Oxide Fuel Cells · Advanced Battery Technologies Research
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (22)
Show source-provided references
1. Effective Testing Matrix for Studying Membrane Durability in PEM Fuel Cells: Part I. Chemical Durability10.1149/1.2356174 ↗
2. Impact of Gas Partial Pressure on PEMFC Chemical Degradation10.1149/1.2356171 ↗
3. Kinumoto · J. Power Sources · 2006 · 158 · 122210.1016/j.jpowsour.2005.10.043 ↗
4. Inaba · Electrochemisty · 2007 · 75 · 20710.5796/electrochemistry.75.207 ↗
5. Gittleman · 2009
6. Lai · J. Fuel Cell. Sci. Technol. · 2009 · 6 · 021002-210.1115/1.2971045 ↗
7. Hygrothermal characterization of the viscoelastic properties of Gore-Select® 57 proton exchange membrane10.1007/s11043-008-9059-4 ↗
8. On the use of pressure-loaded blister tests to characterize the strength and durability of proton exchange membranes10.1115/1.3007431 ↗
9. Fatigue and creep to leak tests of proton exchange membranes using pressure-loaded blisters10.1016/j.jpowsour.2009.06.083 ↗
10. Characterizing fracture energy of proton exchange membranes (PEM) using a knife slit test10.1002/polb.21894 ↗
11. Mechanical properties of a reinforced composite polymer electrolyte membrane and its simulated performance in PEM fuel cells10.1016/j.jpowsour.2007.09.093 ↗
12. Mechanical endurance of polymer electrolyte membrane and PEM fuel cell durability10.1002/polb.20863 ↗
13. On mechanical behavior and in-plane modeling of constrained PEM fuel cell membranes subjected to hydration and temperature cycles10.1016/j.jpowsour.2007.02.025 ↗
14. An experimental investigation of humidity and temperature effects on the mechanical properties of perfluorosulfonic acid membrane10.1016/j.msea.2006.03.055 ↗
15. Durability of perfluorosulfonic acid membranes for PEM fuel cells
16. Mechanical durability characterization and modeling of ionomeric membranes
17. Conductivity, permeability, and ohmic shorting of ionomeric membranes
18. Gittleman · 2012
19. Rodgers · Chem. Rev. · 2012 · 112 · 607510.1021/cr200424d ↗
20. Gasteiger · 2003 · vol. 3 · 593
21. Neutron radiography characterization of an operating proton exchange membrane fuel cell with localized current distribution measurements10.1016/j.nima.2009.01.145 ↗
22. USFCC · 2004