journal article·2017-12

Evolution of thermal stress and failure probability during reduction and re-oxidation of solid oxide fuel cell

Yu Wang, Wenchun Jiang, Yun Luo, Yucai Zhang, Shan-Tung Tu

Publisher page

Abstract

Abstract The reduction and re-oxidation of anode have significant effects on the integrity of the solid oxide fuel cell (SOFC) sealed by the glass-ceramic (GC). The mechanical failure is mainly controlled by the stress distribution. Therefore, a three dimensional model of SOFC is established to investigate the stress evolution during the reduction and re-oxidation by finite element method (FEM) in this paper, and the failure probability is calculated using the Weibull method. The results demonstrate that the reduction of anode can decrease the thermal stresses and reduce the failure probability due to the volumetric contraction and porosity increasing. The re-oxidation can result in a remarkable increase of the thermal stresses, and the failure probabilities of anode, cathode, electrolyte and GC all increase to 1, which is mainly due to the large linear strain rather than the porosity decreasing. The cathode and electrolyte fail as soon as the linear strains are about 0.03% and 0.07%. Therefore, the re-oxidation should be controlled to ensure the integrity, and a lower re-oxidation temperature can decrease the stress and failure probability.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advancements in Solid Oxide Fuel Cells · Fuel Cells and Related Materials · Advanced ceramic materials synthesis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (50)

Show source-provided references
1. Creep analysis of solid oxide fuel cell with bonded compliant seal design10.1016/j.jpowsour.2013.06.096 ↗
2. Component interactions after long-term operation of an SOFC stack with LSM cathode10.1016/j.jpowsour.2011.10.117 ↗
3. Thermal stress analysis of a planar SOFC stack10.1016/j.jpowsour.2006.10.089 ↗
4. Long term performance degradation analysis and optimization of anode supported solid oxide fuel cell stacks10.1016/j.enconman.2016.11.045 ↗
5. Residual stresses and strength of multilayer tape cast solid oxide fuel and electrolysis half-cells10.1016/j.jpowsour.2015.04.105 ↗
6. Modeling of thermal stresses and lifetime prediction of planar solid oxide fuel cell under thermal cycling conditions10.1016/j.jpowsour.2009.10.064 ↗
7. Simulation of thermal stresses in anode-supported solid oxide fuel cell stacks. Part II: loss of gas-tightness, electrical contact and thermal buckling10.1016/j.jpowsour.2008.12.039 ↗
8. Residual stress and redox cycling of segmented-in-series solid oxide fuel cells10.1016/j.jpowsour.2011.01.022 ↗
9. Crack severity in relation to non-homogeneous Ni oxidation in anode-supported solid oxide fuel cells10.1016/j.jpowsour.2010.09.002 ↗
10. Barriers of scaling-up fuel cells: cost, durability and reliability10.1016/j.energy.2014.12.007 ↗
11. System integration, durability and reliability of fuel cells: challenges and solutions10.1016/j.apenergy.2016.12.083 ↗
12. Effect of temperature fluctuation on creep and failure probability for planar solid oxide fuel cell10.1115/1.4031697 ↗
13. Thermal stress and probability of failure analyses of functionally graded solid oxide fuel cells10.1016/j.jpowsour.2010.04.017 ↗
14. Thermal stress and probability of survival investigation in a multi-bundle integrated-planar solid oxide fuel cells IP-SOFC (integrated-planar solid oxide fuel cell)10.1016/j.energy.2014.01.017 ↗
15. Advanced measurement techniques to characterize thermo-mechanical aspects of solid oxide fuel cells10.1016/j.jpowsour.2007.07.072 ↗
16. Ni-8YSZ cermet re-oxidation of anode supported solid oxide fuel cell: from kinetics measurements to mechanical damage prediction10.1016/j.ijhydene.2012.06.019 ↗
17. Mechanical properties of NiO/Ni–YSZ composites depending on temperature, porosity and redox cycling10.1016/j.jeurceramsoc.2008.10.017 ↗
18. Mogensen, Redox stability of SOFC: thermal analysis of Ni–YSZ composites10.1016/j.ssi.2009.04.011 ↗
19. ChemInform abstract: a review of RedOx cycling of solid oxide fuel cells anode
20. Mechanical properties of tape cast nickel-based anode materials for solid oxide fuel cells before and after reduction in hydrogen10.1016/j.actamat.2004.08.023 ↗
21. Testing and improving the redox stability of Ni-based solid oxide fuel cells10.1016/j.jpowsour.2008.11.140 ↗
22. Redox cycling of Ni-Based solid oxide fuel cell anodes: a review10.1002/fuce.200600028 ↗
23. Changes in physical and mechanical properties of SOFC Ni–YSZ composites caused by redox cycling10.1149/1.2883731 ↗
24. Elastic properties of nickel-based anodes for solid oxide fuel cells as a function of the fraction of reduced NiO10.1111/j.1151-2916.2004.tb07499.x ↗
25. Evaluation of elastic properties of reduced NiO-8YSZ anode-supported bi-layer SOFC structures at elevated temperatures in ambient air and reducing environments10.1007/s10853-008-3141-9 ↗
26. Effects of anode porosity on thermal stress and failure probability of planar solid oxide fuel cell with bonded compliant seal10.1016/j.ijhydene.2016.03.117 ↗
27. Mechanical modelling of redox cycling damage in solid oxide fuel cells
28. Solid oxide fuel cells damage mechanisms due to Ni-YSZ re-oxidation: case of the anode supported cell10.1016/j.jpowsour.2009.02.089 ↗
29. Microstructural finite element modeling of redox behavior of Ni–YSZ based ceramic SOFC anodes10.1016/j.ceramint.2016.02.148 ↗
30. Time independent and time dependent probability of failure of solid oxide fuel cells by stress analysis and the Weibull method10.1016/j.jpowsour.2012.07.116 ↗
31. Stress field and failure probability analysis for the single cell of planar solid oxide fuel cells10.1016/j.jpowsour.2008.04.027 ↗
32. RedOx study of anode-supported solid oxide fuel cell10.1016/j.jpowsour.2008.12.118 ↗
33. A numerical tool to estimate SOFC mechanical degradation: case of the planar cell configuration10.1016/j.jeurceramsoc.2007.12.025 ↗
34. 3D coupled CFD/FEM modelling and experimental validation of a planar type air pre-heater used in SOFC technology10.1016/j.ijhydene.2011.02.068 ↗
35. Joint strength of a solid oxide fuel cell glass–ceramic sealant with metallic interconnect10.1016/j.jpowsour.2012.01.048 ↗
36. Thermal cycling and ageing of a glass-ceramic sealant for planar SOFCs10.1016/j.ijhydene.2011.04.083 ↗
37. Effect of aluminizing of Cr-containing ferritic alloys on the seal strength of a novel high-temperature solid oxide fuel cell sealing glass10.1016/j.jpowsour.2008.09.004 ↗
38. Durability of Ni anodes during reoxidation cycles10.1016/j.jpowsour.2010.03.049 ↗
39. Adhesion and interfacial interactions of BaO–SiO2–B2O3-based glass-ceramic seals and AISI430 interconnect for solid oxide fuel cell applications
40. Compilation of mechanical properties for the structural analysis of solid oxide fuel cell stacks, Constitutive materials of anode-supported cells10.1016/j.ceramint.2012.01.043 ↗
41. Effects of crystallization on the high-temperature mechanical properties of a glass sealant for solid oxide fuel cell10.1016/j.jpowsour.2009.12.008 ↗
42. Statistical approaches to failure for ceramic reliability assessment10.1111/j.1151-2916.1988.tb05825.x ↗
43. Ni–YSZ solid oxide fuel cell anode behavior upon redox cycling based on electrical characterization10.1111/j.1551-2916.2007.01909.x ↗
44. Accelerated creep in solid oxide fuel cell anode supports during reduction10.1016/j.jpowsour.2016.04.097 ↗
45. Characterization of time-varying macroscopic electro-chemo-mechanical behavior of SOFC subjected to Ni-sintering in cermet microstructures10.1007/s00466-015-1193-7 ↗
46. Reduction and Re-Oxidation of anodes for solid oxide fuel cells (SOFC)10.1002/9780470291184.ch56 ↗
47. The effect of pre-oxidation treatments on the oxidation tolerance of Ni-yttria-stabilized zirconia anodes in solid oxide fuel cells10.1016/j.jpowsour.2014.07.174 ↗
48. A possible solution to the mechanical degradation of Ni–yttria stabilized zirconia anode-supported solid oxide fuel cells due to redox cycling10.1016/j.jpowsour.2010.03.043 ↗
49. Unidirectional multiple cracking of coatings described through random sequential placement of rods on a line10.1016/S0040-6090(99)00714-2 ↗
50. Strength or toughness? A criterion for crack onset at a notch10.1016/S0997-7538(01)01184-6 ↗