journal article·2004-11

Curvature in solid oxide fuel cells

Wenxia Li, Kathy Hasinska, Matt Seabaugh, Scott Swartz, John Lannutti

Journal of Power Sources· Volume 138· Issue 1-2
Publisher page

Abstract

At this point in history, curvature is inherent to the laminated components that comprise solid oxide fuel cells (SOFCs). Surprisingly, however, this fact has never been previously quantified in the literature. In addition, potential curvature changes associated with NiO reduction and re-oxidation during operation have not been investigated. In this report, an optical profilometer was employed to non-destructively quantify the surface curvature or cracking behavior observed on a large scale in industrially manufactured cells. This provides insights into the challenges that the component materials face as well as additional appreciation for why, in spite of a concerted effort to commercialize SOFC power generation, all currently manufactured SOFC stacks fail. Our results demonstrate that cracked electrolyte areas (caused by differential sintering) are flatter than uncracked regions. The height of the electrolyte surface ranged from 86 to 289 μm above the baseline following sintering. Reduction typically results in increases in curvature of up to 214 μm. Initial crack density appears to affect curvature evolution during reduction; the higher the crack density, the smaller the curvature increase following reduction at 600 °C. In general, however, we observed that the electrolyte layer is remarkably resistant to further cracking during these typographic changes. Following oxidation at 750 °C, large changes in curvature (up to 280 μm) are noted that appear to be related to the strength of the bond between the electrolyte and the underlying anode.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advancements in Solid Oxide Fuel Cells · Electronic and Structural Properties of Oxides · Semiconductor materials and devices

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (12)

Show source-provided references
1. Bordia · J. Am. Ceram. Soc. · 1985 · 68 · 28710.1111/j.1151-2916.1985.tb15227.x ↗
2. Evans · Acta Metall. Mater. · 1995 · 43 · 250710.1016/0956-7151(94)00444-M ↗
3. Hillman · J. Am. Ceram. Soc. · 1996 · 79 · 212710.1111/j.1151-2916.1996.tb08946.x ↗
4. Tomaszewski · J. Mater. Sci. · 2000 · 35 · 416510.1023/A:1004823429336 ↗
5. Okuyama · J. Ceram. Soc. Jpn. · 1993 · 101 · 100110.2109/jcersj.101.1001 ↗
6. Garino · Ceram. Eng. Sci. Proc. · 2002 · 23 · 75910.1002/9780470294741.ch89 ↗
7. Majumdar · J. Am. Ceram. Soc. · 1986 · 69 · 62810.1111/j.1151-2916.1986.tb04821.x ↗
8. Sørensen · J. Mater. Sci. · 1998 · 33 · 529110.1023/A:1004429829323 ↗
9. Cai · J. Am. Ceram. Soc. · 1997 · 80 · 192910.1111/j.1151-2916.1997.tb03075.x ↗
10. Selcuk · J. Mater. Sci. · 2001 · 36 · 117310.1023/A:1004833909780 ↗
11. Mori · J. Electrochem. Soc. · 1998 · 145 · 137410.1149/1.1838468 ↗
12. Stathis · J. Mater. Res. · 2002 · 17 · 95110.1557/JMR.2002.0142 ↗