journal article·2018-02Open access

Strain distribution and failure mode of polymer separators for Li-ion batteries under biaxial loading

Sergiy Kalnaus, Abhishek Kumar, Yanli Wang, Jianlin Li, Srdjan Simunovic, John A. Turner, Phillip Gorney

Abstract

Abstract Deformation of polymer separators for Li-ion batteries has been studied under biaxial tension by using a dome test setup. This deformation mode provides characterization of separator strength under more complex loading conditions, closer representing deformation of an electric vehicle battery during crash event, compared to uniaxial tension or compression. Two polymer separators, Celgard 2325 and Celgard 2075 were investigated by deformation with spheres of three different diameters. Strains in separators were measured in situ by using Digital Image Correlation (DIC) technique. The results show consistent rupture of separators along the machine direction coinciding with areas of high strain accumulation. The critical first principal strain for failure was independent of the sphere diameter and was determined to be approximately 34% and 43% for Celgard 2325 and Celgard 2075 respectively. These values can be taken as a criterion for internal short circuit in a battery following an out-of-plane impact. A Finite Element (FE) model was built with the anisotropic description of separator behavior, derived from tensile tests in orthogonal directions. The results of simulations predicted the response of separator rather well when compared to experimental results for various sizes of rigid sphere.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Battery Technologies Research · Polymer crystallization and properties · Recycling and Waste Management Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (23)

Show source-provided references
1. A review on the separators of liquid electrolyte Li-ion batteries10.1016/j.jpowsour.2006.10.065 ↗
2. Battery separators10.1021/cr020738u ↗
3. R.S. Baldwin, W.R. Bennett, E.K. Wong, M.R. Lewton, M.K. Harris, Battery separator characterization and evaluation procedures for NASAs advanced lithium-ion batteries, NASA/TM 2010 216099.
4. ASTM D4830/D4830M 98 · 2014
5. Doughty · 2006 · 43
6. Evaluation of mechanical abuse techniques in lithium ion batteries10.1016/j.jpowsour.2013.08.066 ↗
7. Mechanical behavior of representative volume elements of lithium-ion battery modules under various loading conditions10.1016/j.jpowsour.2013.09.128 ↗
8. Rate- and temperature-dependent material behavior of a multilayer polymer battery separator10.1007/s11665-013-0743-4 ↗
9. Mechanical properties of a battery separator under compression and tension10.1149/2.0191411jes ↗
10. Deformation and fracture behaviors of microporous polymer separators for lithium ion batteries10.1039/c4ra00983e ↗
11. Mechanical behavior of a battery separator in electrolyte solutions10.1016/j.jpowsour.2011.06.026 ↗
12. Mechanical behavior and failure mechanisms of Li-ion battery separators10.1016/j.jpowsour.2017.03.003 ↗
13. X. Zhang, E. Sahraei, K. Wang, Li-ion battery separators, mechanical integrity and failure mechanisms leading to soft and hard internal shorts, Sci. Rep. https://doi.org/10.1038/srep32578.10.1038/srep32578 ↗
14. Effect of polymer blending and drawing conditions on properties of polyethylene separator prepared for Li-ion secondary battery10.1016/S0378-7753(02)00097-6 ↗
15. Three dimensional structure of Celgard microporous membranes10.1016/S0376-7388(00)81364-2 ↗
16. Materials processing for lithium-ion batteries10.1016/j.jpowsour.2010.11.001 ↗
17. Spherical indentation of freestanding circular thin films in the membrane regime10.1016/j.jmps.2004.03.002 ↗
18. Spherical indentation of a freestanding circular membrane revisited: analytical solutions and experiments10.1016/j.jmps.2017.01.005 ↗
19. Plastic behavior and stretchability of sheet metals. Part I: a yield function for orthotropic sheets under plane stress conditions10.1016/0749-6419(89)90019-3 ↗
20. Plastic behavior and stretchability of sheet metals. Part II: effect of yield surface sape on sheet forming limit10.1016/0749-6419(89)90026-0 ↗
21. 2017
22. Bunge · 2000 · 334
23. Friction and wear characteristics of ultrahigh molecular weight polyethylene (UHMWPE) composites containing glass fibers and carbon fibers under dry and water-lubricated conditions10.1016/j.wear.2017.03.006 ↗