The influence of cycling temperature and cycling rate on the phase specific degradation of a positive electrode in lithium ion batteries: A post mortem analysis
Source abstract
Abstract
Abstract The influence of cycling temperatures and cycling rates on the cycling stability of the positive electrode (cathode) of commercial batteries are investigated. The cathode is a mixture of LiMn2O4 (LMO), LiNi0.5Co0.2Mn0.3O2 (NCM) and LiNi0.8Co0.15Al0.05O2 (NCA). It is found that increasing the cycling temperature from 25 °C to 40 °C is detrimental to the long term cycling stability of the cathode. Contrastingly, the improved cycling stability is observed for the cathodes cycled at higher charge/discharge rate (2C/3C instead of 1C/2C). The microstructure analysis by X-ray powder diffraction reveals that a significant capacity fading and an increased overvoltage is observed for NCM and NCA in all the fatigued cathodes. After high number of cycling (above 1500 cycles), NCM becomes partially inactive. In contrast to NCM and NCA, LMO shows a good cycling stability at 25 °C. A pronounced degradation of LMO is only observed for the fatigued cathodes cycled at 40 °C. The huge capacity losses of NCM and NCA are most likely because the blended cathodes were cycled up to 4.12 V vs. the graphite anode during the cycle-life test (corresponds to 4.16 V vs. Li+/Li); which is beyond the stability limit of the layered oxides below 4.05 V vs. Li+/Li.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advancements in Battery Materials · Advanced Battery Materials and Technologies · Advanced Battery Technologies Research
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (46)
Show source-provided references
1. The kinetic effect on structural behavior of mixed LiMn2O4–LiNi1/3Co1/3Mn1/3O2 cathode materials studied by in situ time-resolved X-ray diffraction technique10.1016/j.elecom.2011.11.027 ↗
2. High-temperature storage performance of Li-Ion batteries using a mixture of Li-Mn spinel and Li-Ni-Co-Mn oxide as a positive electrode material10.1149/1.1843792 ↗
3. Investigation on the dissolution of Mn ions from LiMn2O4 cathode in the application of lithium ion batteries: first principle molecular orbital method10.1002/qua.24314 ↗
4. Capacity fade model for spinel LiMn2O4 electrode10.1149/2.026302jes ↗
5. A review of blended cathode materials for use in Li-ion batteries10.1016/j.jpowsour.2013.09.052 ↗
6. Lithium diffusion behavior and improved high rate capacity of LiNi1/3Co1/3Mn1/3O2 as cathode material for lithium batteries10.1016/j.ssi.2011.11.020 ↗
7. Structural changes and thermal stability of charged LiNi1/3Co1/3Mn1/3O2 cathode material for Li-ion batteries studied by time-resolved XRD10.1016/j.jpowsour.2008.10.130 ↗
8. Prevention of the Micro cracks generation in LiNiCoAlO2 cathode by the restriction of DOD10.1149/1.4717964 ↗
9. Ageing mechanisms in lithium-ion batteries10.1016/j.jpowsour.2005.01.006 ↗
10. Temperature dependent ageing mechanisms in Lithium-ion batteries - a Post-Mortem study10.1016/j.jpowsour.2014.03.112 ↗
11. Capacity fade of LiAlyNi1-x-yCoxO2 cathode for lithium-ion batteries during accelerated calendar and cycle life tests (surface analysis of LiAlyNi1-x-yCoxO2 cathode after cycle tests in restricted depth of discharge ranges)10.1016/j.jpowsour.2014.02.018 ↗
12. Crystal structure and multicomponent effects in Li1+xMn2−x−yAlyO4 cathode materials for Li-ion batteries10.1016/j.jpowsour.2014.03.120 ↗
13. Simulation and analysis of stress in a Li-ion battery with a blended LiMn2O4 and LiNi0.8Co0.15Al0.05O2 cathode10.1016/j.jpowsour.2013.08.113 ↗
14. Evaluation of commercial lithium-ion cells based on composite positive electrode for plug-in hybrid electric vehicle applications. Part I: initial characterizations10.1016/j.jpowsour.2011.08.077 ↗
15. Advantages of blending LiNi0.8Co0.2O2 into Li1+xMn2-xO4 cathodes10.1016/S0378-7753(01)00753-4 ↗
16. Charge-discharge characteristics and phase transitions of mixed LiNi0.8Co0.2O2 and LiMn2O4 cathode materials for lithium-ion batteries
17. Electrochemical evaluation of mixed oxide electrode for Li-ion secondary batteries: Li1.1Mn1.9O4 and LiNi0.8Co0.15Al0.05O210.1016/j.jpowsour.2005.03.031 ↗
18. Synergies in blended LiMn2O4 and Li[Ni1/3Mn1/3Co1/3]O2 positive electrodes10.1149/2.056210jes ↗
19. A novel high-throughput setup for in situ powder diffraction on coin cell batteries10.1107/S1600576715022165 ↗
20. The new material science powder difffraction beamline at ALBA synchrotron10.1017/S0885715613000900 ↗
21. Recent advances in magnetic structure determination by neutron powder diffraction10.1016/0921-4526(93)90108-I ↗
22. Ab-initio structure determination of LiSbWO6 by X-ray powder diffraction10.1016/0025-5408(88)90019-0 ↗
23. Post mortem analysis of fatigue mechanisms in LiNi0.8Co0.15Al0.05O2 - LiNi0.5Co0.2Mn0.3O2 - LiMn2O4/graphite lithium ion batteries10.1016/j.jpowsour.2016.07.010 ↗
24. Comparative issues of cathode materials for Li-Ion batteries10.3390/inorganics2010132 ↗
25. Improved high rate capacity and lithium diffusion ability of LiNi1∕3Co1∕3Mn1∕3O2 with ordered crystal structure10.1149/2.010205jes ↗
26. Chemical diffusion coefficients of lithium in LiMyMn2-yO410.1016/0167-2738(96)00213-5 ↗
27. Understanding structural changes in NMC Li-ion cells by in situ neutron diffraction10.1016/j.jpowsour.2014.01.010 ↗
28. Changes in the crystal and electronic structure of LiCoO2 and LiNiO2 upon Li intercalation and de-intercalation10.1039/b901200a ↗
29. First-principles investigation of phase stability in LixCoO210.1103/PhysRevB.58.2975 ↗
30. Fundamental degradation mechanisms of layered oxide Li-ion battery cathode materials: methodology, insights and novel approaches10.1016/j.mseb.2014.11.014 ↗
31. Identifying battery aging mechanisms in large format Li ion cells10.1016/j.jpowsour.2010.07.029 ↗
32. Capacity fade analysis of a lithium ion cell10.1016/j.jpowsour.2008.01.028 ↗
33. Studies on the cycle life of commercial lithium ion batteries during rapid charge – discharge cycling10.1016/S0378-7753(01)00821-7 ↗
34. The cathode-electrolyte interface in the Li-ion battery10.1016/j.electacta.2004.03.049 ↗
35. A new coating method for alleviating surface degradation of LiNi0.6Co0.2Mn0.2O2 cathode material: nanoscale surface treatment of primary particles10.1021/acs.nanolett.5b00045 ↗
36. A review on lithium-ion battery ageing mechanisms and estimations for automotive applications10.1016/j.jpowsour.2013.05.040 ↗
37. Electrochemical evaluation on composite cathode blends of LiMn2O4 and LiNi0.8Co0.2O210.1016/S1388-2481(01)00195-3 ↗
38. The elevated temperature performance of the LiMn2O4/C system: failure and solutions10.1016/S0013-4686(99)00209-1 ↗
39. Improved capacity retention in rechargeable 4 V lithium/lithium-manganese oxide (spinel) cells10.1016/0167-2738(94)90450-2 ↗
40. Correlation between dissolution behavior and electrochemical cycling performance for LiNi1/3Co1/3Mn1/3O2-based cells10.1016/j.jpowsour.2012.01.122 ↗
41. Unraveling the degradation process of LiNi0.8Co0.15Al0.05O2 electrodes in commercial lithium ion batteries by electronic structure investigations10.1021/acsami.5b03191 ↗
42. Surface reconstruction and chemical evolution of stoichiometric layered cathode materials for lithium-ion batteries10.1038/ncomms4529 ↗
43. Large plastic deformation in high-capacity lithium-ion batteries caused by charge and discharge10.1111/j.1551-2916.2011.04432.x ↗
44. The stability of the SEI layer, surface composition and the oxidation state of transition metals at the electrolyte-cathode interface impacted by the electrochemical cycling: X-ray photoelectron spectroscopy investigation10.1039/c2cp41134b ↗
45. Surface characterization of electrodes from high power lithium-ion batteries10.1149/1.1505636 ↗
46. Reprint of “Studies of local degradation phenomena in composite cathodes for lithium-ion batteries”10.1016/j.electacta.2007.10.009 ↗