journal article·2011-02

Service life estimation of liquid silicone rubber seals in polymer electrolyte membrane fuel cell environment

Tong Cui, C.-W. Lin, C.H. Chien, Y.J. Chao, J.W. Van Zee

Journal of Power Sources· Volume 196· Issue 3
Publisher page

Abstract

Abstract Polymer electrolyte membrane fuel cell (PEMFC) is a promising power source for many applications such as automobiles. Sealing around the perimeter of the cell is required to prevent the gases/liquids inside the cell from leaking and polymers are usually used for the seal or gasket materials. They in general possess the viscoelastic property which induces stress relaxation of the material under constant strain. The stress relaxation behavior of liquid silicone rubber, a type of polymer used as seals in PEMFCs, is studied in this work. A Prony series is used to predict the compression stress relaxation curve at different strain levels. Applying the time–temperature superposition, master curves are generated and used for predicting the service life of this material as seals in PEMFCs. The estimated lives in water and in air are compared.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Fuel Cells and Related Materials · Tribology and Wear Analysis · Lubricants and Their Additives

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (21)

Show source-provided references
1. US Department of Energy, in: Hydrogen, Fuel Cells & Infrastructure Technologies Program, 2007, p. 7.
2. Patankar · Mechanics of Time-Dependent Materials · 2008 · 12 · 22110.1007/s11043-008-9059-4 ↗
3. K. Patankar, M.W. Ellis, M. Budinski, S.W. Case, Y.-H. Lai, C. Gittleman, in: The 7th International Conference on Fuel Cell Science, Engineering and Technology, Newport Beach, CA, 2009.
4. Liu · Journal of Engineering Materials and Technology-Transactions of the ASME · 2006 · 128 · 50310.1115/1.2345441 ↗
5. Bauer · Journal of Polymer Science, Part B: Polymer Physics · 2005 · 43 · 78610.1002/polb.20367 ↗
6. Husar · Journal of Power Sources · 2007 · 169 · 8510.1016/j.jpowsour.2007.01.078 ↗
7. Tian · International Journal of Hydrogen Energy · 2010 · 35 · 277210.1016/j.ijhydene.2009.05.015 ↗
8. Schulze · Journal of Power Sources · 2004 · 127 · 22210.1016/j.jpowsour.2003.09.017 ↗
9. Ronan · Materials & Design · 2007 · 28 · 151310.1016/j.matdes.2006.03.009 ↗
10. Tan · International Journal of Hydrogen Energy · 2010 · 1
11. Tan · Materials Science and Engineering a-Structural Materials Properties Microstructure and Processing · 2007 · 445 · 66910.1016/j.msea.2006.09.098 ↗
12. Tan · Materials Science and Engineering a-Structural Materials Properties Microstructure and Processing · 2008 · 496 · 46410.1016/j.msea.2008.05.052 ↗
13. Tan · Journal of Power Sources · 2007 · 172 · 78210.1016/j.jpowsour.2007.05.026 ↗
14. Junisbekov · 2003
15. A.L. Rabinovich, Introduction to the Mechanics of Reinforced Polymers, Moscow, 1970.
16. T. Alfrey, Mechanical Properties of High Polymers, Moscow, 1952.
17. Hiemenz · 2007
18. Andrews · Journal of Polymer Science · 1951 · 7 · 22110.1002/pol.1951.120070210 ↗
19. L.C.E. Struik, Physical aging in amorphous polymers and other materials, Elsevier Scientific Pub. Co., Distributors for the U.S. and Canada, Elsevier North-Holland, Amsterdam, New York, 1978.
20. ASTM D6147, in: ASTM International, West Conshohochen, PA, 2002.
21. Derham · Plastic Rubber and Composites Proceeding and Applications · 1997 · 26 · 130