journal article·2021-08

High pressure effect on the substructure and hardness of IF steel during martensitic transformation

Zuohua Wang, Haidong Sun, Changji Li, Ning Liu, Shuai Zhang, Pinwen Zhu, Dongli Yu, Hongwang Zhang

Acta Materialia· Volume 214
Publisher page

Abstract

No abstract is available for this record. The assistant can identify its topic from the title, but cannot infer the study’s results.

Source: Not provided · Quality: missing

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Microstructure and mechanical properties · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (54)

Show source-provided references
1. Martensite in steel: strength and structure10.1016/S0921-5093(99)00288-9 ↗
2. A laser heating device for metallographic studies
3. Effect of hydrostatic pressure on martensitic transformation10.2320/matertrans1989.38.668 ↗
4. Effects of pressure on the structure of iron-carbon martensites10.1016/0001-6160(67)90179-4 ↗
5. Martensite in interstitial-free steel obtained by ultra-high pressure10.1016/j.scriptamat.2011.10.002 ↗
6. Unprecedented strength in pure iron via high-pressure induced nanotwinned martensite10.1080/21663831.2019.1612792 ↗
7. High pressure induced ultra-hard twinned lath martensite in binary Fe-15wt.%Cr alloy10.1016/j.scriptamat.2020.06.004 ↗
8. The morphology and crystallography of lath martensite in alloy steel10.1016/j.actamat.2006.07.009 ↗
9. Characteristics of lath martensite: Part I. crystallographic and substructural features10.1007/BF02644284 ↗
10. Ber den mechanismus der stahlhrtung
11. Über den Mechanismus der α-γ Umwandlung des Eisens
12. X-ray investigation of the mechanism of the transformation from face centered cubic lattice to body centered cubic
13. Effects of transformation temperature on variant pairing of bainitic ferrite in low carbon steel10.1016/j.actamat.2011.12.018 ↗
14. The morphology and crystallography of lath martensite in Fe-C alloys10.1016/S1359-6454(02)00577-3 ↗
15. Crystallographic features of lath martensite in low-carbon steel10.1016/j.actamat.2005.11.001 ↗
16. Effect of carbon content on variant pairing of martensite in Fe–C alloys10.1016/j.actamat.2012.09.046 ↗
17. Substructures of lenticular martensites with different martensite start temperature in ferrous alloys10.1016/j.actamat.2008.09.030 ↗
18. Twinned substructure in lath martensite of water quenched Fe-0.2 %C and Fe-0.8 %C steels10.1016/j.jmst.2019.12.025 ↗
19. Microstructures and hardness of as-quenched martensites (0.1–0.5%C)10.1016/j.actamat.2011.05.061 ↗
20. Evaluation of temper softening behavior of Fe–C binary martensitic steels by nanoindentation10.1016/j.scriptamat.2003.08.025 ↗
21. Role of silicon in quenching and partitioning treatment of low-carbon martensitic stainless steel10.2355/isijinternational.52.1377 ↗
22. Effect of block size on the strength of lath martensite in low carbon steels10.1016/j.msea.2005.12.048 ↗
23. Relationship between nanohardness and microstructures in high-purity Fe-C as-quenched and quench-tempered martensite10.1557/JMR.2003.0201 ↗
24. Effect of martensitic morphology on mechanical properties of an as-quenched and tempered 25CrMo48V steel10.1016/j.msea.2011.11.078 ↗
25. Evaluation of the block boundary and sub-block boundary strengths of ferrous lath martensite using a micro-bending test10.1016/j.msea.2010.08.026 ↗
26. Micromechanical characterization of deformation behavior in ferrous lath martensite10.1016/j.jallcom.2012.01.066 ↗
27. A review of focused ion beam milling techniques for TEM specimen preparation10.1016/S0968-4328(99)00005-0 ↗
28. Microstructure of as-quenched 3.5 NiCrMoV rotor steel10.1002/mawe.19870180607 ↗
29. A simple method for observing ω-Fe electron eiffraction spots from <112>α-Fe directions of quenched Fe–C twinned martensite10.2355/isijinternational.ISIJINT-2017-270 ↗
30. Direct observation of deformation twinning under stress gradient in body-centered cubic metals10.1016/j.actamat.2018.05.061 ↗
31. Ultra grain refinement and hardening of IF-steel during accumulative roll-bonding10.1016/j.msea.2005.06.058 ↗
32. Structural characterization of ultrafine-grained interstitial-free steel prepared by severe plastic deformation10.1016/j.actamat.2015.12.039 ↗
33. Microstructure and mechanical properties after annealing of equal-channel angular pressed interstitial-free steel10.1016/j.actamat.2011.03.026 ↗
34. On the occurrence of blocky martensite in 300M steel10.1016/0025-5416(84)90137-X ↗
35. Laser surface heat treatment of AISI 4340 steel: A microstructural study10.1016/0025-5416(81)90201-9 ↗
36. On the microstructural evolution pattern toward nano-scale of an AISI304 stainless steel during high strain rate surface deformation10.1016/j.jmst.2020.01.027 ↗
37. Thermodynamics and kinetics of martensitic transformations10.1016/0502-8205(58)90005-4 ↗
38. Kinetics of the austenite→martensite transformation
39. A general mechanism of martensitic nucleation: Part II. FCC → BCC and other martensitic transformations
40. The effect of high pressure on the martensitic reaction in iron-carbon alloys10.1016/0001-6160(62)90117-7 ↗
41. Effects of pressure on phase equilibria and transformation in the iron-chromium system10.1016/0001-6160(69)90072-8 ↗
42. The lattice stability of metals—III. Iron10.1016/0001-6160(63)90157-3 ↗
43. Austentie to bainite phase transformation in the heat-affected zone of a high strength low alloy steel10.1016/j.actamat.2004.01.025 ↗
44. An approximate approach for the calculation of Ms in iron-based alloys10.1007/BF00555894 ↗
45. Pressure dependence of yielding and associated volume expansion in tempered martensite10.1016/0001-6160(75)90205-9 ↗
46. Brandes · 1992
47. The effect of pressure on diffusion10.4028/www.scientific.net/DDF.129-130.57 ↗
48. Effect of hydrostatic pressure on the kinetics of recrystallization in high-purity copper10.1016/0001-6160(62)90169-4 ↗
49. The mechanism of plastic deformation of crystals. Part I.—Theoretical
50. The deformation and ageing of mild steel: III discussion of results10.1088/0370-1301/64/9/303 ↗
51. The cleavage strength of polycrystals
52. Microstructure and strength of nickel at large strains10.1016/S1359-6454(00)00082-3 ↗
53. The plastic deformation of polycrystalline aggregates10.1080/14786436208201857 ↗
54. Dislocation density within lath martensite in Fe-C and Fe-Ni Alloys10.2355/isijinternational.43.1475 ↗