Evaluation of the intergranular crack growth resistance of ultrafine grained tungsten materials
Source abstract
Abstract
Abstract The brittleness of tungsten at room temperature represents a severe challenge particularly for structural applications. Tungsten composites, consisting of foils or wires, overcome this low ductility by utilizing the remarkable mechanical properties of ultrafine grained tungsten materials. A comprehensive understanding of the fracture behaviour of these ultrafine grained tungsten materials is therefore essential for a further development of high performance structural composites. However, the dimensions of specimens used for classical fracture toughness experiments are not applicable to test all important crack growth directions in the case of thin foils and wires, especially, in the direction of the presumably lowest fracture toughness, which is along their characteristically elongated microstructure. Femtosecond laser processing allows to fabricate micro single leg bending specimens, which enable to properly evaluate the fracture toughness in this orientation. The fracture toughness value at crack initiation found for the foil is 2.4 MPa m , whereas for the wire a value of 5.3 MPa m was determined. In both cases the results are significantly below the values reported for other orientations. This strongly anisotropic fracture behaviour is responsible for the reduced brittle to ductile transition temperature and the delamination induced toughening for crack orientations perpendicular to the elongated ultrafine grained structure. The distinct difference of the fracture toughness at crack initiation and the R-curve between wire and foil specimens could be primarily explained by the morphologies of the fracture surfaces, exhibiting significantly different roughnesses of the evolving crack paths.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and mechanical properties · Advanced materials and composites · Advanced Surface Polishing Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (39)
Show source-provided references
1. Recent progress in research on tungsten materials for nuclear fusion applications in europe10.1016/j.jnucmat.2012.08.018 ↗
2. Development of advanced high heat flux and plasma-facing materials10.1088/1741-4326/aa6f71 ↗
3. Lassner · 1999
4. Methods for improving ductility of tungsten - a review10.1016/j.ijrmhm.2018.04.012 ↗
5. Ductilisation of tungsten (w): tungsten laminated composites10.1016/j.ijrmhm.2017.07.013 ↗
6. Enhanced toughness and stable crack propagation in a novel tungsten fibre-reinforced tungsten composite produced by chemical vapour infiltration10.1088/0031-8949/2014/T159/014031 ↗
7. Behavior of tungsten fiber-reinforced tungsten based on single fiber push-out study10.1016/j.nme.2016.04.010 ↗
8. Chemically deposited tungsten fibre-reinforced tungsten the way to a mock-up for divertor applications10.1016/j.nme.2016.03.005 ↗
9. Fracture toughness investigations of tungsten alloys and spd tungsten alloys10.1016/j.jnucmat.2007.03.079 ↗
10. Mechanical behavior and dynamic failure of high-strength ultrafine grained tungsten under uniaxial compression
11. Effect of low-temperature rolling on the tensile behavior of commercially pure tungsten10.1016/j.msea.2008.01.013 ↗
12. Fracture toughness of polycrystalline tungsten alloys10.1016/j.ijrmhm.2010.04.007 ↗
13. Anisotropic fracture behaviour and brittle-to-ductile transition of polycrystalline tungsten10.1080/14786435.2010.504198 ↗
14. Tensile behaviour of drawn tungsten wire used in tungsten fibre-reinforced tungsten composites10.1088/1402-4896/aa891d ↗
15. Tungsten foil laminate for structural divertor applications tensile test properties of tungsten foil10.1016/j.jnucmat.2012.12.003 ↗
16. Fracture toughness evaluation of UFG tungsten foil10.1016/j.ijrmhm.2018.06.008 ↗
17. The effect of heat treatments on pure and potassium doped drawn tungsten wires: Part II Fracture properties10.1016/j.msea.2018.09.029 ↗
18. Utke · 2011
19. The use of femtosecond laser ablation as a novel tool for rapid micro-mechanical sample preparation10.1016/j.matdes.2017.02.012 ↗
20. Cold rolled tungsten (W) plates and foils: evolution of the microstructure10.1016/j.ijrmhm.2016.06.020 ↗
21. Improved fracture behavior and microstructural characterization of thin tungsten foils10.1016/j.nme.2016.06.003 ↗
22. The effect of heat treatments on pure and potassium doped drawn tungsten wires: Part I - microstructural characterization10.1016/j.msea.2018.09.027 ↗
23. Cold rolled tungsten (W) plates and foils: evolution of the tensile properties and their indication towards deformation mechanisms10.1016/j.ijrmhm.2017.09.007 ↗
24. A single leg bending test for interfacial fracture toughness determination10.1007/BF00034525 ↗
25. Femtosecond laser-induced periodic surface structures10.2351/1.4712658 ↗
26. Tensile behaviour of micro-sized copper wires studied using a novel fibre tensile module10.3139/146.101690 ↗
27. An analytical crack-tip element for layered elastic structures10.1115/1.2895931 ↗
28. II - on the problem of crack extension in brittle solids under general loading
29. On the crack extension in plates under plane loading and transverse shear10.1115/1.3656897 ↗
30. Fracture toughness of polycrystalline tungsten under mode I and mixed mode I/II loading10.1016/S0921-5093(99)00252-X ↗
31. The low temperature brittle fracture behaviour of steel in mixed modes I and II10.1016/0013-7944(91)90076-D ↗
32. R. C. Shah, Fracture under combined modes in 4340 steel, fracture analysis: Proceedings of the 1973 National Symposium on Fracture Mechanics, Part IIdoi:10.1520/STP33131S.10.1520/STP33131S ↗
33. Anderson · 1994
34. Fracture mechanics of micro samples: fundamental considerations10.1016/j.matdes.2018.09.004 ↗
35. A study into the crack propagation resistance of pure tungsten10.1016/j.engfracmech.2012.07.021 ↗
36. Statistical approach to roughness-induced shielding effects10.1111/j.1460-2695.2004.00734.x ↗
37. Local and equivalent stress intensity factors for tortuous cracks under remote mode II loading10.1016/j.tafmec.2019.01.030 ↗
38. Stress intensity factors for rough cracks loaded in mode II10.4028/www.scientific.net/SSP.258.310 ↗
39. Characterization of the fracture toughness of micro-sized tungsten single crystal notched specimens10.1080/14786435.2012.658449 ↗