Selective oxidation-induced strengthening of Zr/Nb nanoscale multilayers
Source abstract
Abstract
The paper presents a new approach, based on controlled oxidation of nanoscale metallic multilayers, to produce strong and hard oxide/metal nanocomposite coatings with high strength and good thermal stability. The approach is demonstrated by performing long term annealing on sputtered Zr/Nb nanoscale metallic multilayers and investigating the evolution of their microstructure and mechanical properties by combining analytical transmission electron microscopy, nano-mechanical tests and finite element models. As-deposited multilayers were annealed at 350 C in air for times ranging between 1 - 336 hours. The elastic modulus increased by approx. 20% and the hardness by approx. 42% after 15 hours of annealing. Longer annealing times did not lead to changes in hardness, although the elastic modulus increased up to 35% after 336 hrs. The hcp Zr layers were rapidly transformed into monoclinic ZrO2 (in the first 15 hours), while the Nb layers were progressively oxidised, from top surface down towards the substrate, to form an amorphous oxide phase at a much lower rate. The sequential oxidation of Zr and Nb layers was key for the oxidation to take place without rupture of the multi-layered structure and without coating spallation, as the plastic deformation of the metallic Nb layers allowed for the partial relieve of the residual stresses developed as a result of the volumetric expansion of the Zr layers upon oxidation. Moreover, the development of residual stresses induced further changes in mechanical properties in relation to the annealing time, as revealed by finite element simulations.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal and Thin Film Mechanics · High-Temperature Coating Behaviors · Boron and Carbon Nanomaterials Research
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (29)
Show source-provided references
1. Length-scale-dependent deformation mechanisms in incoherent metallic multilayered composites10.1016/j.actamat.2005.06.025 ↗
2. The microstructure and mechanical behavior of Mg/Ti multilayers as a function of individual layer thickness10.1016/j.actamat.2013.10.032 ↗
3. Strain rate sensitivity of nanolayered Cu/X (X=Cr,Zr) micropillars: heterophase interfaces/nanotwin boundaries effects10.1016/j.msea.2014.06.025 ↗
4. Microstructure and strengthening mechanisms in Cu/Fe multilayers10.1016/j.actamat.2012.08.005 ↗
5. Deformability of ultrahigh strength 5 nm Cu/Nb nanolayered composites10.1063/1.2938921 ↗
6. A Length-scale-dependent mechanical behaviour of Zr/Nb multilayers as a function of individual layer thickness10.1016/j.msea.2015.02.071 ↗
7. Phase stability of bcc Zr in Nb/Zr thin film multilayers10.1016/S1359-6454(03)00380-X ↗
8. Proximity effect in Nb/Zr multilayers with variable Nb/Zr ratio10.1016/S0038-1098(03)00444-7 ↗
9. The effects of decreasing layer thickness on the high temperature mechanical behavior of Cu/Nb nanoscale multilayers10.1016/j.tsf.2006.01.036 ↗
10. Optimum high temperature strength of two-dimensional nanocomposites10.1063/1.4828757 ↗
11. Thermal stability of Cu–Nb nanolamellar composites fabricated via accumulative roll bonding10.1080/14786435.2012.731527 ↗
12. High-strength and thermally stable bulk nanolayered composites due to twin-induced interfaces10.1038/ncomms2651 ↗
13. Thermal stability of self-supported nanolayered Cu/Nb films10.1080/14786430310001659480 ↗
14. High-temperature mechanical behavior/microstructure correlation of Cu/Nb nanoscale multilayers10.1016/j.msea.2007.08.089 ↗
15. Zirconia layer formed by high temperature oxidation of pure zirconium: stress generated at the zirconium/zirconia interface10.1007/s11085-012-9348-9 ↗
16. A study of the stresses generated in zirconia films during the oxidation of zirconium alloys10.1007/BF00614620 ↗
17. The oxidation of metals at high temperatures
18. Modelling of the mechanical behavior of the metal–oxide system during Zr alloy oxidation10.1016/S0022-3115(98)00045-2 ↗
19. The Effect of Stress on the Low-temperature Oxidation of Niobium10.31274/rtd-180817-1932 ↗
20. Measuring substrate-independent modulus of thin films10.1557/jmr.2011.8 ↗
21. Piezospectroscopic study of residual stresses in Al2O3-ZrO2 directionally solidified eutectics10.1111/j.1151-2916.2000.tb01626.x ↗
22. The properties of RF sputtered Zirconium Oxide thin films at different plasma gas ratio10.5012/bkcs.2010.31.02.397 ↗
23. Influence of sputtering pressure on the structure and properties of ZrO2 films prepared by rf reactive sputtering10.1016/S0169-4332(00)00888-6 ↗
24. Elasticity module and hardness of niobium and tantalum anode oxide films
25. Oxidation of Zr and related phases in Zr-Nb alloys: an electron microscopy investigation10.1016/S0022-3115(99)00153-1 ↗
26. Exponent for Hall–Petch behaviour of ultra-hard multilayers10.1080/14786430500080353 ↗
27. Hibbit · 2011
28. Tabor · 2000
29. An improved technique for determining hardness and elastic modulus using load and displacement-sensing indentation systems10.1557/JMR.1992.1564 ↗