Electrical resistivity monitoring of a SiC/[Si-B-C] composite under oxidizing environments
Source abstract
Abstract
Abstract The introduction of Ceramic Matrix Composites parts in civil aeronautics requires a thorough understanding of their evolution under the oxidizing environments present within the engines. In this respect, a SiCf/PyC/[Si-B-C]m material has been tested in fatigue at 450 °C and 100 MPa (which is a typical stress during take-off) under two types of environmental conditions: ambient air, and moist air with an imposed water pressure of 10 kPa. Static fatigue and cyclic fatigue at a frequency of 1 Hz were both performed with these two conditions. As expected, the additional presence of moisture contributes to increase the degradation of the mechanical properties of the material, leading to shorter lifetimes and higher increases in electrical resistivity. It is shown that the pyrocarbon interphases are the main electrical conductors in this material: the electrical resistance can therefore be an accurate indicator of the damage state of these interphases, which are sensitive to the oxidizing environment. The global resistance increase presents two distinct phases of evolution in the four tests performed, with a transition around 35–40% of the time to failure. A model is proposed to account for this global resistance change, which proves to be in good agreement with experimental results. Moreover, the evolution of the electrical resistivity during the interposed unload-reload cycles can give key information about the state of the fiber/matrix interfaces which are critical for mechanical properties. Finally, electrical resistance monitoring seems to provide information on the damage state of the material complementary to acoustic emission results, allowing an unprecedented assessment of the evolution of the interphases state during ageing under oxidizing environments.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Smart Materials for Construction · Advanced ceramic materials synthesis · High voltage insulation and dielectric phenomena
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (30)
Show source-provided references
1. Design, preparation and properties of non-oxide CMCs for application in engines and nuclear reactors: an overview10.1016/S0266-3538(03)00230-6 ↗
2. Design, fabrication, and application of thermostructural composites like C/C, C/SiC, and SiC/SiC composites10.1002/adem.200290001 ↗
3. Engine test and post engine test characterization of self-sealing ceramic matrix composites for nozzle applications in gas turbine engines
4. Composites in aerospace industry10.4028/www.scientific.net/AST.50.153 ↗
5. Ceramic matrix composites to make breakthroughs in aircraft engine performance
6. Advances in self-healing ceramic matrix composites
7. Oxidation-resistant carbon-fiber-reinforced ceramic-matrix composites10.1016/S0266-3538(98)00146-8 ↗
8. Fracture mechanisms for SiC fibers and SiC/SiC composites under stress-rupture conditions at high temperatures
9. Oxidation of carbon fibers and films in ceramic matrix composites: a weak link process10.1016/0008-6223(95)00034-B ↗
10. Modelling the effect of oxidation on the creep behavior of fibre-reinforced ceramic matrix composites10.1016/S1359-6454(03)00189-7 ↗
11. Stress-dependent matrix cracking in 2D woven SiC-fiber reinforced melt-infiltrated SiC matrix composites10.1016/j.compscitech.2003.10.022 ↗
12. Analysis of acoustic emission energy release during static fatigue tests at intermediate temperatures on ceramic matrix composites: towards rupture time prediction10.1016/j.compscitech.2012.03.011 ↗
13. Analysis of damage mechanisms and associated acoustic emission in two SiC/[Si–B–C] composites exhibiting different tensile behaviours. Part I: damage patterns and acoustic emission activity10.1016/j.compscitech.2007.12.001 ↗
14. Load and failure analyses of CFRP laminates by means of electrical resistivity measurements10.1016/0266-3538(89)90016-X ↗
15. Damage detection of carbon fiber reinforced polymer composites via electrical resistance measurement10.1016/j.compositesb.2010.08.005 ↗
16. Resistivities of conductive composites10.1063/1.352350 ↗
17. Influence of micro-cracking on the composite resistivity of engineered cementitious composites10.1016/j.cemconres.2014.01.002 ↗
18. Electrical resistance measurement for in situ monitoring of fatigue of carbon fabric composites10.1016/j.ijfatigue.2009.02.044 ↗
19. On the fatigue life prediction of CFRP laminates using the Electrical Resistance Change method10.1016/j.compscitech.2011.01.003 ↗
20. Evaluation of dispersion and damage sensing of carbon fiber polypropylene (PP)-polyamide (PA) composites using 2 dimensional electrical resistance mapping10.1016/j.compositesa.2016.08.009 ↗
21. Monitoring damage accumulation in CMCs using electrical resistivity10.1016/j.scriptamat.2008.04.033 ↗
22. Monitoring interlaminar crack growth in ceramic matrix composites using electrical resistance10.1016/j.scriptamat.2014.10.034 ↗
23. Electrical resistance as a Nondestructive Evaluation Technique For SiC/SiC CMC under creep-rupture loading10.1111/j.1744-7402.2010.02587.x ↗
24. Electrical resistance and acoustic emission during fatigue testing of pristine and high velocity impact SiC/SiC composites at room and elevated temperature
25. Monitoring damage evolution of SiC/[Si-B-C] composites using electrical resistivity: crack density-based electromechanical modeling10.1016/j.actamat.2016.11.036 ↗
26. High-temperature fatigue behavior of SiC-coated carbon/carbon composites in oxidizing atmospheres10.1016/j.jeurceramsoc.2008.06.014 ↗
27. Modeling of simultaneous oxidation and volatilization phenomena along a crack in a self-healing multi-constituent material10.1007/s11085-016-9708-y ↗
28. The role of interfaces in fiber-reinforced brittle matrix composites10.1016/0266-3538(91)90010-M ↗
29. Modal acoustic emission of damage accumulation in a woven SiC/SiC composite10.1016/S0266-3538(98)00121-3 ↗
30. Bertran · 2013