journal article·2024-01Open access

Synthesis and characterization of (Al,Si)3(Zr,Ti)-D022/D023 intermetallics: Understanding the stability of silicon substitution

Juan-Ricardo Castillo-Sánchez, Georges Salloum-Abou-Jaoude, Aïmen E. Gheribi, Paul Lafaye, Kentaro Oishi, Jean-Philippe Masse, Etienne Bousser, Gilles L’Espérance, Jean-Philippe Harvey

Acta Materialia· Volume 262

Abstract

(Al,Si) 3(Zr,Ti)-D0 22/D0 23 are phases that may form in aerospace and automotive aluminium alloys. The substitution of Zr/Ti in these solid solutions is widely reported in the literature; however, it remains relatively unexplored for Si. In this work, in situ precipitation of (Al,Si) 3(Zr,Ti)-D0 22/D0 23 intermetallics was performed using Al-Si-Zr-Ti alloys. The precipitation, sedimentation and concentration of numerous intermetallic particles were accomplished by filtrating the residual molten aluminium using a temperature/pressure-controlled vessel adapted with a PoDFA filter. A combination of SEM, TEM, XRD and EMP analysis allowed the identification of (Al,Si) 3(Zr,Ti)-D0 22/D0 23 intermetallics concentrated within α -FCC matrices of non-Si-doped (sample S2) and Si-doped (samples S4 and S6) alloys. EDS analysis confirmed that Zr and Ti substitute each other in the D0 22 and D0 23 phases, whereas Si substitutes in Al sites. Acceptance of Si inside the D0 23 phase was not expected according to FTlite (FactSage) and TCAL7 (Thermo-Calc) databases. Additionally, Si was found to enhance the formation of (Al,Si) 3(Zr,Ti)-D0 22 intermetallics with high Zr-content, contrary to FactSage 7.3 predictions. TEM results showed intermetallic/FCC crystal coherency for samples S2 and S6, implying that these intermetallics acted as nucleation sites for the Al-phase due to their small lattice mismatch. Furthermore, Si site occupancy was calculated for both (Al,Si) 3Ti-D0 22 and (Al,Si) 3Zr-D0 23 phases via DFT, showing that sites 2 b and 4 e are the most favorable for Si occupation, respectively. Finally, a thermodynamic model is derived to describe Si substitution upon solidification. Experimental and numerical examinations indicate that Si substitution preferentially occurs in the D0 22 intermetallics compared to the D0 23 phase.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Intermetallics and Advanced Alloy Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (75)

Show source-provided references
1. Influence of ultrasonic melt treatment on the formation of primary intermetallics and related grain refinement in aluminum alloys10.1007/s10853-011-5463-2 ↗
2. On the mechanism of grain refinement in Al–Zr–Ti alloys10.1016/j.jallcom.2010.09.046 ↗
3. TiAlSi intermetallic formation and its impact on the casting processing in Al–Si alloys10.1016/j.jmatprotec.2010.06.009 ↗
4. Microstructure control in ingots of aluminum alloys with an emphasis on grain refinement
5. Grain refinement of aluminum casting alloys10.1007/BF03355416 ↗
6. Effects and mechanisms of grain refinement in aluminium alloys10.1007/BF02708630 ↗
7. Effects of solutes on grain refinement of selected wrought aluminium alloys10.1179/mst.1997.13.8.650 ↗
8. The influence of Inter-cooling and electromagnetic stirring above liquidus on the formation of primary Al3Zr and grain refinement in an Al-0.2% Zr alloy10.3390/ma12010022 ↗
9. A review on grain refinement of aluminum alloys: Progresses, challenges and prospects10.1007/s40195-017-0565-8 ↗
10. Grain refinement of aluminium alloys by inoculation10.1002/adem.200390013 ↗
11. Grain refinement of aluminium and its alloys by heterogeneous nucleation and alloying10.1179/095066001225001049 ↗
12. Understanding mechanisms of grain refinement of aluminium alloys by inoculation10.1179/026708304225022359 ↗
13. Mechanism of grain refinement in aluminum alloys10.1007/BF03397424 ↗
14. A new insight into heterogeneous nucleation mechanism of Al by non-stoichiometric TiCx10.1016/j.actamat.2022.117977 ↗
15. Effect of high-intensity ultrasonic irradiation on the modification of solidification microstructure in a Si-rich hypoeutectic Al–Si alloy10.1016/j.matchemphys.2010.09.035 ↗
16. The grain refinement mechanism of cast aluminium by zirconium10.1016/j.actamat.2013.05.044 ↗
17. Grain refinement of commercially pure aluminum with addition of Ti and Zr elements based on crystallography orientation
18. Effect of ultrasonic processing on a direct chill cast AA6082 aluminium alloy
19. Mechanical analysis of toughness degradation due to premature fracture of course inclusions in wrought aluminium alloys10.1016/S0921-5093(99)00658-9 ↗
20. New studies of nucleation mechanisms in aluminium alloys: Implications for grain refinement practice10.1179/mst.1998.14.5.394 ↗
21. Polmear · 2005
22. Emerging trends in aluminum recycling: Reasons and responses
23. Microstructure and Properties of a Novel Al-Mg-Si Alloy AA 608610.3390/met11020368 ↗
24. Growth related metastable phase selection in a 6xxx series wrought Al alloy10.1016/S0921-5093(00)01545-8 ↗
25. Assessment of different techniques for quantification of α-Al (FeMn) Si and β-AlFeSi intermetallics in AA 6xxx alloys10.1016/S1044-5803(03)00036-6 ↗
26. Electron microscope studies of Al-Fe-Si intermetallics in an Al-11 Pct Si alloy10.1007/s11661-006-0141-8 ↗
27. Enhancing mechanical properties of twin-roll cast Al–Mg–Si–Fe alloys by regulating Fe-bearing phases and macro-segregation10.1016/j.msea.2021.142256 ↗
28. Structure and mechanical behavior of in situ developed Mg2Si phase in magnesium and aluminum alloys–a review10.1039/D0RA02744H ↗
29. Theoretical and experimental study of relaxations in Al3Ti and Al3Zr ordered phases10.1103/PhysRevLett.74.4955 ↗
30. Criteria of grain refinement induced by ultrasonic melt treatment of aluminum alloys containing Zr and Ti10.1007/s11661-010-0232-4 ↗
31. Influences of nickel and vanadium impurities on microstructure of aluminum alloys10.1007/s11837-013-0572-9 ↗
32. Lattice matching of D023 and D022 phases in Al-6at.%(Ti,V,Zr) systems10.1016/S0921-5093(96)10857-1 ↗
33. First principle calculations of structural, electronic and thermodynamic properties of Al3(TixV1−x) alloy in D022 and L12 structures10.1016/j.solidstatesciences.2012.11.003 ↗
34. Crystal chemistry and thermodynamic modelling of the Al13(Fe,TM)4 solid solutions (TM=Co, Cr, Ni, Pt)10.1016/j.jallcom.2022.165779 ↗
35. A comprehensive study on the thermodynamics of the Al13Fe4 solid solution in the Al-Fe-Mn ternary system10.1016/j.jallcom.2023.169054 ↗
36. Impact of aluminum alloys and microstructures on engineering propertiesreview
37. Processing and precipitation strengthening of 6xxx series aluminium alloys: A review10.22271/27078221.2020.v1.i1a.10 ↗
38. The improvement of mechanical properties of friction-stir-welded A356 Al alloy10.1016/S0921-5093(03)00053-4 ↗
39. FactSage thermochemical software and databases10.1016/S0364-5916(02)00035-4 ↗
40. The compound energy formalism10.1016/S0925-8388(00)01481-X ↗
41. A new Zr-rich intermetallic phase in an Al-14Si-3Cu-4.5 Ni casting alloy with trace additions of Zr10.1016/j.intermet.2019.106667 ↗
42. Investigation of silicon sublattice substitution within (Al,Si)3Zr intermetallics via DFT simulations10.1088/1757-899X/1281/1/012055 ↗
43. Strukturbestimmung an einigen Phasen in den Systemen: Zr-Al-Si und Hf-Al-Si{ZrAl3(Si); ZrSi(Al), Hf(Si,Al); Zr3Si2; Hf3Si2}10.1007/BF00914988 ↗
44. Effects of Si and Ge addition on the Al3Zr precipitates in an Al–0.6 mass.% Zr alloy
45. Intermetallic compound formation in the Zr–Al–Si ternary system10.1016/S1044-5803(02)00343-1 ↗
46. Structure of anodized Al–Zr sputter deposited coatings and effect on optical appearance10.1016/j.apsusc.2014.09.037 ↗
47. Efficient iterative schemes for ab initio total-energy calculations using a plane-wave basis set10.1103/PhysRevB.54.11169 ↗
48. From ultrasoft pseudopotentials to the projector augmented-wave method10.1103/PhysRevB.59.1758 ↗
49. Generalized gradient approximation made simple10.1103/PhysRevLett.77.3865 ↗
50. III.–Investigations of the specific heat of solid bodies
51. Lafaye · 2017
52. Experimental study, first-principles calculation and thermodynamic modelling of the Cr–Fe–Nb–Sn–Zr quinary system for application as cladding materials in nuclear reactors10.1016/j.jnucmat.2020.152692 ↗
53. The Rietveld method10.1088/0031-8949/89/9/098002 ↗
54. First-principles calculations of binary Al compounds: Enthalpies of formation and elastic properties10.1016/j.calphad.2011.09.009 ↗
55. The influence of Zr alloying on the structure and properties of Al3Ti10.1016/S0966-9795(02)00234-0 ↗
56. Preparation and structure of Al3Ti10.3891/acta.chem.scand.40a-0157 ↗
57. On the transferability of classical pairwise additive atomistic force field to the description of unary and multi-component systems: Applications to the solidification of Al-based alloys10.1039/D2CP02746A ↗
58. Substitution behavior of Si in Al3Ti (D022): a first-principles study
59. Ultrasound assisted in-situ casting technique for synthesizing small-sized blocky Al3Ti particles reinforced A356 matrix composites with improved mechanical properties10.1016/j.jallcom.2018.02.010 ↗
60. Stability and elastic properties of L12-(Al,Cu)3(Ti,Zr) phases: Ab initio calculations and experiments10.1016/j.intermet.2006.03.003 ↗
61. FP-LAPW investigation of structural, electronic, and thermodynamic properties of Al3V and Al3Ti compounds10.1016/j.physb.2010.06.053 ↗
62. First-principles calculations of binary Al compounds: Enthalpies of formation and elastic properties10.1016/j.calphad.2011.09.009 ↗
63. Structural stability, mechanical properties and stacking fault energies of TiAl3 alloyed with Zn, Cu, Ag: First-principles study10.1016/j.jallcom.2016.01.106 ↗
64. An ab initio study on stacking and stability of TiAl3 phases10.1016/j.commatsci.2018.07.011 ↗
65. Theoretical investigations on structural, elastic, thermodynamic and electronic properties of Al3Ti and Al3V compounds in L12 structure under high pressure10.1088/2053-1591/aafec0 ↗
66. Exploration of D022-Type Al3TM (TM=Sc, Ti, V, Zr, Nb, Hf, Ta): Elastic anisotropy, electronic structures, work function and experimental design10.3390/ma14092206 ↗
67. Ab initio calculation of the formation energies of L12, D022, D023 and one dimensional long period structures in TiAl3 compound10.1016/S0966-9795(02)00054-7 ↗
68. Stability, elastic properties and electronic structures of the stable Zr–Al intermetallic compounds: A first-principles investigation10.1016/j.jallcom.2013.12.079 ↗
69. First-principles study of phase stability and solubility in Al-(Cu,Zr) alloys10.1080/00150193.2018.1392130 ↗
70. Generality of the 18-n rule: Intermetallic structural chemistry explained through isolobal analogies to transition metal complexes10.1021/acs.inorgchem.5b02016 ↗
71. An orthorhombic D022-like precursor to Al8Mo3 in the Al–Mo–Ti system10.1016/j.jallcom.2020.153807 ↗
72. First-principles phase stability calculations of pseudobinary alloys of (Al,Zn)3Ti with L12, D022, and D023 structures10.1007/s11669-006-9007-4 ↗
73. Ternary intermetallics in aluminiumrefractory metal-X systems (X= V, Cr, Mn, Fe, Co, Ni, Cu, Zn)10.1179/095066090790324037 ↗
74. Continuous chemical analysis of molten aluminum
75. Analysis of dissolved titanium concentration and phase transformation in molten Al–Ti alloy using laser-induced breakdown spectroscopy10.1016/j.sab.2022.106387 ↗